iNFinuvo Hovo 710 User manual

PUSH
MODEL NO.:Hovo 710
®
®

Product Features
Product Parts
Product Illustration
Product Operations and User Interface Icons
Battery Installation and Storage
Charging Dock Station and Battery Charging Methods
Product Operations By Remote Control Unit
Schedule Cleaning Time
Virtual Blocker Operations

Only a certified technician can disassemble and/or repair the product.
non-authorized
Do not use product near any flammables.
Do not clean while product is charging.
Do not over bend or put large weight on the power cord.
This product is for indoor use and clean dry surface floor only.
Before using, remove damageable objects (glass, textiles, papers, etc.)
that can get caught in the cleaner's brush or vacuum intake.
Before charging battery,
To avoid injury; inform all people in the house that the unit is doing cleaning.
Use this product in temperatures between 0°C and 40°C (32°F and 104°F).
Remove battery from unit before recycling
Disconnect AC adapter before removing the battery.
The battery should be properly disposed.
NOTE: Do not allow children to operate this product unless they are
supervised by an adult
Follow these precautions to reduce the risk of injury or damage.
Save this user manual.
Read this user manual thoroughly and carefully before using this product.
Before using this product, please read the following safety
instructions and follow all normal safety precautions.
make sure to (1) connect AC adapter to cleaner or charging base first;
(2) then plug the adapter to the wall outlet next sequence to avoid sparks.
or scraping the unit.

P r o d u c t F e a t u r e s
1. Voice message guidance and touch screen operations
2. Self-adjustable carriage of suction assembly and/or sweeping assembly so
they will be closer to the ground to do better cleaning.
3. Patented ONE FIT ALL brush system with both soft bristle and
rubber base to do good cleaning both on hard surface floor
and carpet floor. The entangled hairs on brush blades can be
easily cleaned and brush blades are replaceable.
4. Two-way 6”long wide high wattage UV lamp which kills up to 99% of
bacteria both on floor and in dustbin.
5. Pre-filter and High-Efficiency Particle Absorption (HEPA) filter removes over
99% of airborne particles including mold, dust, and dust mites.
6. Two-way virtual blocker can create one or two invisible barriers that
cleaner will not cross.
7. Reduce motor noise level manually (MUTE) or via lighting sensor.
8. Interchangeable sweeping assembly (for carpet cleaning) and suction only
assembly (for hard surface floor cleaning).

P r o d u c t F e a t u r e s
9. Dustbin full condition alarm warning
10. Dark area cleaning mode – Cleaner will clean under bed or sofa area
for about 5 minutes.
11. Garbage/Dirt detection – Cleaner will increase suction power to clean
the area.

05
PUSH
cleaner * 1 set Charging dock
station * 1pcs Remote controller * 1pcs
Power adapter * 1pcs Trailing bar * 1pcs Mop * 2pcs
Suction inlet * 1pcs Side brush * 2pcs extra HEPA filter * 1pcs extra
P r o d u c t P a r t s
Main Unit and Accessories
PUSH
MODEL NO.:Hovo 710

PUSH
P r o d u c t I l l u s t r a t i o n
bin
out
Manual charging port
Front wheel

07
SPOT
AUTO
DOCK
UV
UV
1234
5 6 7
UV
SPOT AUTO DOCK
Note: Remove the small items or obstacles in the house before cleaning, especially the
power cord and other objects that may be easily; if the battery is low during
cleaning, the cleaner stops cleaning and beeps five times,
AUTO Automatic cleaning button:
Press this button to start automatic cleaning; if the battery is low during cleaning, it will
look for charging dock station automatically;
During the cleaning process, touch any button on the panel to stop cleaning.
SPOT Spot cleaning button
Press this button, the cleaner automatically enters a range about 1m and cleans this area
in spiral mode;
During the cleaning process, touch any button on the panel to stop cleaning.
DOCK Charging button
Press this button, and the cleaner will search for
SCHEDULE
Press the SCHEDULE button on the remote control, the “ ” icon turns on, and the
cleaner enters current week, hour/minute and time week, hour/minute settings (see
Remote control schedule setting on page 11).
UV
When the “ ” icon is on, the UV lamp of the machine tarts working; when
the icon is off, the UV lamp is
Note: When the cleaner is powered on in the first time, the system turns on UV lamp by default.
Product Operations and User Interface Icons
P r o d u c t O p e r a t i o n s a n d U s e r I n t e r f a c e I c o n s
then search for charging station
and recharge battery.
it will clean the area for about 2-3 minutes and stop.
charging station to recharge battery automatically.
is on and s
turned off.
get tangled

1234
5 6 7
2
P r o d u c t O p e r a t i o n s a n d U s e r I n t e r f a c e I c o n s
Battery Installation and Storage
Week day displays: 1 for Monday, 2 for Tuesday, 3 for Wednesday, 4 for Thursday,
5 for Friday, 6 for Saturday, 7 for Sunday
ging the cleaner battery, turn the power switch ON first!
Otherwise cleaner battery cannot be recharged and it will show E010 error code.
you empty and clean dustbin and brushes after each use.
er movement path is set by default and
changes to spiral spot cleaning mode automatically if very dirty area is detected.
s for about five minutes,then it will go back to AUTO mode
automatically.
Enter dark cleaning mode, you can either put the cleaner in the dark area or push
DARK button on remote control unit.
be used for an extended period of time, we recommend that you remove the
battery. For long-term storage, fully charge the battery first, then remove it, and store it in a cool,
dry place.

Charging Dock Station and Battery Charging Methods
A. Auto charging via charging dock station
5. Press DOCK on control panel or remote control, then cleaner will return to charging station
Plug AC adapter power cord to the manual charging socket on unit first, then plug AC adapter to
wall outlet next. Make sure to turn on cleaner power switch to recharge battery.It takes about
and against the wall. 2 meters in front
0.5 meters on both sides.
dock station for automatic battery charging.
charging.
and recharge battery.
B. Manual charging battery
wrap the DC power cord on the back of charging
dock station, and do not put the power cord on the ground.
Otherwise, it will affect the searching of charging dock station
3 hours to fully charge a low power battery.

AAA
AAA
10
PUSH
≤4m
Remote control buttons
Press“ ” and the cleaner will
Press“ ” to turn on/off the UV lamp on the bottom of the cleaner.
Press“ ” and the cleaner will enter energy saving mute cleaning mode.
Press“ ” and the cleaner will enter spiral/spot cleaning mode.
Press“ ” and the cleaner will enter sleep working mode (in sleep
mode, press and hold this button for 10 seconds to enter the working mode).
Press“ ” and the cleaner will enter time/schedule clean setting.
Press“ ” and the cleaner will enter dark cleaning mode.
Press“ ” to confirm (in standby mode, press this button to enter
-following cleaning mode).
Press“ ” and the cleaner will enter automatic cleaning mode.
Press“ ” and the cleaner will forward.
Press“ ” and the cleaner will backward.
Press“ ” and the cleaner will to the left.
Press“ ” and the cleaner will to the right.
Note: 1. using the remote controller, two AAA batteries first. (Fig. 2)
2. To control the cleaner with the remote controller, aim the remote controller at the sensor of the
cleaner within 4 (Fig. 3).
Fig. 1
Fig. 2 Fig. 3
P r o d u c t O p e r a t i o n s B y R e m o t e C o n t r o l U n i t
search charging dock station and recharge battery.
(reduce motors noise level).
or
ing
wall
move
move
move
move
Before install
meters or 13 feet
Press OK key to stop.
Press OK key to stop.
Press OK key to stop.
3. When battery power is low, the remote control’s effective distance will be shorter.
If your vacuum does not respond well to the remote, please replace remote batteries ASAP.

S c h e d u l e C l e a n i n g T i m e
Day of The Week and Time Setting
Day of The Week Setting:
day of the week setting;
to select day of the week and it will be steady;
to cancel day of the week selection and it flashes;
day of the week and enter current Hour/Minute setting;
Hour and Minutes Setting:
day of the week, press
Cleaning Time Setting
Day of the Week:
steady; press the “ ”button to cancel
Day of week selection and it flashes;
You can read current setting value by press “OK”after enter schedule Day of the week setting or
cleaning time setting.

12
AA
AA
Side IR window
Front IR window
0
1 2
3
1.Front
0 Power switch.
2.Side
3.Front, side
2m
2m
Turn button Can : turn off power of virtual blocker, switch among front, side, front/side.
Turn to 0 position, the power supply of the virtual blocker will be cut off.
Turn to position 1, the power supply of the virtual blocker is turned on; the machine is in
front working mode , and the control range of the virtual blocker is within 2meters;
Turn to position 2, the power supply of the virtual blocker is turned on; the blocker is in
side working mode, and the control range of the virtual blocker is within 2meters;
Turn to position 3, the power supply of the virtual blocker is turned on; th is in
dual working mode (front side) , and the control range of the virtual blocker is within 2meters;
Introduction of virtual blocker
Side indicator Front indicator
Fig.1 Fig.2
01 2 3
Side switch
Fig.3
1. Before using it, open the bottom battery compartment cover on of virtual blocker, and insert two AA
batteries properly according to the instructions (Fig. 3).
Note: Incorrect battery polarity installation may result in operation failure or damage of the virtual blocker,
and may
cause other unex pected occurrence.
2. The battery life time depends on working modes and frequent of usage. In order to save
battery power, please select appropriate virtual blocker working mode to reduce the transmission
power; when the virtual blocker is not in use, turn the power off .
3. The virtual blocker is virtual blocker.
4. During use, ensure that the virtual blocker and the vacuum cleaner are placed
on the same
(Fig. 4).
5. In actual use, the effective distance of virtual blocker depends on the
environment, movement of the cleaner and remaining battery power.
6. The virtual blocker should be at least 50cm from the cleaner, otherwise it
will cause interference.
7. Do not aim the IR emission window/hole at people’s eyes!
Fig. 4
V i r t u a l B l o c k e r O p e r a t i o n s
How to Operate Virtual Blocker
level, and there is no obstruction between the virtual
blocker and the cleaner
e blocker
+
often placed near stairs, by the door, or at any places that requires a

bin cover.(Fig.1)
bin cover,and pour out the dirt and other rubbish (Fig.3,4 & 5).
and pre-filter
Pre-filter

TT

Drive shaft
Fig. 1
Fig. 4
rubber
cap
Fig. 3
Fig. 2

action on solution column below to eliminate
hairs or debris entangled
on wheels Clear the hairs or debris on the left
and right wheels
Hairs or debris wrapped on left
and right side brushes Clear hairs or dirt on the left and right side brushes
hairs wrapped on roller brush Clear hairs or debris
on the roller brush
bumper sensors
failure bumper sensors are blocked
Hovo 710
solution
customer service of your local distributor.
Unit dimension 13.5”diameter 3.5”height
700ml
Dustbin capacity
Empty dustbin,clean dirt on
sensor tip and suction inlet

Hovo 710
05X105 mm
Hovo 710
Hovo 710
Dimension
Dimension
Dimension
. 2 AAA batteries (not included)
. 2 AA batteries (not included)
Hovo 710
40X70X95 mm
Dimension
AC adapter
Output
100-240V 50/60Hz 0.8A
24VDC 1.0A

Metapo Inc.
http://www.infinuvo.com
http://www.metapo.com
For technical support and manufacturer warranty: http://support.metapo.com
Warranty services coverage only valid if you buy products from our authorized resellers.