iNFinuvo Hovo mini User manual

Find us at: www.infinuvo.com

Use the original battery. 5V USB cable and AC charger should
be plugged to wall outlet for vacuum battery charging. DO
NOT use the computer USB port to charge the vacuum battery.
Otherwise it can damage the product.
Stop using the product if you noticed the unit is defective.
Email [e-mail] for further assistance.
Do not expose the product to any liquids. The product is not
waterproof.
Do not use vacuum close to stairs without blocker to avoid
vacuum from falling.
Do not drag the product by is charging cable. Folding or
placing heavy objects on the USB cable may damage the
cable.
Do not leave product near a fire or any flammable, explosive,
or corrosive material.
Body or clothes contact with the vacuum suction can lead to
personal injury.
1.6 Warranty
3.1 Battery installation
3.2 Install and remove side brushes
4. Product operation
5.2 Product cleaning
5.3 Dust bin cleaning
5.3.1 Dust bin removal
5.4 Sensor cleaning

Do not handle the
product by its
front bumper. Pick
up the product by
its main body with
your hands.
Take out the
battery if you do
not plan on using
the vacuum for a
while.
Charge the vacuum
for 8 hours if it is
your first time
using it or if you
have not used it in
a while.
Only use a 5V USB
cable. Using other
cables that are
not 5V can cause
short circuit the
product or cause
fire.
Adult supervision is required if a child
is using the vacuum.
Packaging can suffocate children, do
not let them play with it.
Only use the battery that came with
the vacuum.
Separate the battery from the
vacuum when you throw the
product away.
Visit www.infinuvo.com if you need
a battery replacement or email
[email protected]
If you get in contact with battery
liquid, wipe it away with a dry cloth
immediately.
Rechargeable batteries should be
recycled according to US federal
guidelines.
This product should be used only on hard surface floor as shown below NOT carpet floor.
Do not use vacuum close to stairs without blocker to
avoid vacuum from falling.
Do not use product to vacuum printer toners. This can
cause a fire.
Do not use product to vacuum sharp objects like glass or
nails. This can damage the product.
1.6 Warranty
Visit www.infinuvo.com
Register your product now to activate your warranty
Get technical support
Request warranty service (only valid if you buy products from authorized
resellers)
Find answers on frequently asked questions (FAQ)
Learn maintenance tips
Video demos
How to buy accessories
Attentions
This product is
for indoor
use only
Protect the product
from water, oil or
other liquid
Collect the wires on
the floor before
cleaning
Move away all fragile
things before
cleaning

USB cable
Battery is pre-installed in the robot.
Top view
Front bumper
Dust bin
USB charging port
Bottom view
Side brush (R) Side brush (L)
Battery compartment
Note:
USB
cable

3.1 Battery Installation
a. Unscrew battery compartment cover
b. Connector wires (red, white and black) should match battery wires colors.
Connect battery with black color connector which only allow wires insertion
correctly and make sure connector is locked
c. Put battery inside compartment with wires under battery and put back
compartment cover with screw.
3.2 Install and remove side brushes
Make sure L mark side brush is installed on the L side and R mark side brush is
installed on the R side.
a. Side brush installation
b. Side brush removal
4. Product operation
Note:
4.1.1. Operational instructions:
Before operation, please clean large debris on the floor, especially wires
scattered on the floor, which may entangle the brushes.
a. Auto mode
Press the START button once, a beep sound will be heard, the robot starts to
work with the blue indicator on after 3 seconds.
b. Low clearance dark area mode
Press the START button twice within 3 seconds, the robot starts to work with
blue indicator flashing, use this mode to clean under bed, sofa and other
furnitures dark area.
Side brush is removable. Hold 2 bristles of side brush and pull
it out gently.

4.1.2. Product running mode
a. Auto mode
Robot won't stop cleaning until the
battery runs out. It will move around
walls, barriers and stairs automatically.
Once low clearance dark area is detected,
the robot will clean it for 5 minutes
with high cleaning efficiency. Working
path is as shown in the picture 1.
b. Low clearance dark area mode
In low clearance dark area mode, the
robot will clean continuously for 15
minutes and move around walls, barriers
and stairs automatically. Working path
is as shown in the picture 2.
If the robot is lifted up while it is cleaning, the robot's wheel will stop
immediately, and the vacuum motor will stop after 3 seconds.
Press the button during the working process, the robot's wheel will stop
immediately, and the vacuum motor will stop after 3 seconds.
Low clearance dark area mode
Indicator flashes once
with one beep
with one beep
with one beep
with one beep
with one beep
with one beep
with one beep
with one beep dust bin
If the robot is working in low clearance dark area, it will leave low clearance
dark area immediately once it detects the low battery status.
After the robot runs out of power, the red indicator will flash. The robot will
beep every 10 seconds for 10 minutes in order help the user locate the robot.
If the robot stops working, press and hold the button for 5 seconds to turn off
the robot.
Blue indicator stays on
Once the robot is
stay on.

5.1 Daily Storage
If you plan on not using your vacuum for a while,
make sure the battery is fully charged and remove it
from the vacuum and store it in a cool and dry
environment.
5.2 Product cleaning
5.3 Dust bin cleaning
5.3.1 Dust bin removal
dust bin
dust bin
dust bin
dust bin
dust bin
5.4 Sensor cleaning
We recommend cleaning the sensor
after each use. Use a cotton cloth to
wipe the sensors clean. Also clean the
front wheel and side brushes to
prevent it from getting stuck.
Dust bin can be cleaned with water.
Note:
Note:
dust bin

Robot only moves
backwards
Please contact [e-mail] if problem does not resolve.
Note:
Note:
dust bin 35ML
Infinuvo reserves the right to make any technical or design changes to the product
as a result of continuous product improvement.
Check whether battery has sufficient power.
Fully charge robot battery if necessary.
Input current
Avoid using the robot under strong light
Avoid using the robot on dark color floor
If so, please clean it.
Clean the ground detectors on the bottom of
the vacuum.
Check the indicator status listed on page 10