InFocus INF5520 User manual

Regulatory model: INF5520
HDDQ1008010
HHDDQ1008010x



Declaration of Conformity
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon 97223-8368 USA
We declare under our sole responsibility that this tablet conforms to the following directives and norms:
•EMC Directive 2004/108/EC:
oEN 55022
oEN 55024
oEN 61000-3-2
oEN 61000-3-3
•Low Voltage Directive 2006/95/EC
•Safety: IEC 60950-1:2005
Trademarks
Apple, Mac and Facetime are trademarks or registered trademarks of Apple, Inc. Microsoft, Windows, PowerPoint, Excel and Word
are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of
Adobe Systems Incorporated. Vidtel is a trademark of Vidtel, Inc. InFocus, In Focus, INFOCUS (stylized) and Mondopad are either
registered trademarks or trademarks of InFocus Corporation in the United States and other countries. All other trademarks are the
property of their respective owners. Any other trademarks, service marks, personal names or product names are assumed to be the
property of their respective owners and are used only for reference. There is no implied sponsorship, affiliation, certification,
approval or endorsement if we use one of these terms.
FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of the equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense. Changes or modifications not expressly approved by InFocus Corporation may void
authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation.
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to
take adequate measures. The typical use is in a conference room, meeting room or auditorium.
Canada
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
INFORMATION FOR RADIO FREQUENCY DEVICES ONLY:
This device complies with part 15 of the FCC Rules / RSS-210. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation.
INFORMATIONS POUR LES DISPOSITIFS À RADIO FRÉQUENCE UNIQUEMENT :
Cet appareil est conforme à l’article 15 des réglementations de la FCC / CNR-210. Le fonctionnement est subordonné aux deux
conditions suivantes : (1) ce appareil ne doit pas provoquer d’interférences nuisibles, et (2) ce appareil doit accepter toute
interférence reçue, y compris des interférences qui peuvent provoquer un fonctionnemnent non désiré.
INFORMATION FOR OPTICAL POINTING DEVICES ONLY:
This product has been tested to comply with International Standard IEC 60825-1: (1993), incld. Amd. 2(2001). This product uses
LEDs that are inherently Class 1.
INFORMATION POUR LES DISPOSITIFS DE POINTAGE OPTIQUE SEULEMENT :
Ce produit a été testé pour se conformer à la norme IEC 60825-1 : (1993), y comp. Amd. 2 (2001). Ce produit utilize des DEL qui
sont, par nature, de classe 1.

Dongle Label: RG-0918
IC : 8150A-RG0918
CMIIT ID:2009DJ2362
CFT: RCPINRG11-0903
FCC ID: E8HRG-0918
Waste Electrical and Electronie Equipment-WEEE
NOTE: This product is covered electrical and electronic equipment under the European Union’s Waste from
Electrical and Electronic Equipment (“WEEE”) Directive (2002/96/EC). The WEEE Directive requires that covered
equipment be collected and managed separately from typical household waste in all EU member states. Please
follow the guidance of your local environmental authority or ask the shop where you purchased the product for
collection or recycling options.
Energy Star
As an ENERGY STAR Partner, InFocus Corporation has determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
ENERGY STAR®is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy
aimed at saving money and protecting the environment through energy efficient products and practices.
We are proud to offer our customers products with an ENERGY STAR compliant design. This product has been designed and
tested to conform to the ENERGY STAR program requirement for computers at the time of manufacture.
By using ENERGY STAR compliant products and taking advantage of the power management features of your computer, you
reduce the consumption of electricity. Reduced electrical consumption contributes to potential financial saving, a cleaner
environment, and the reduction of greenhouse gas emissions. For more information about ENERGY STAR, go to:
http://www.energystar.gov. We encourage you to make efficient use of energy an integral part of your daily operations. To help in
this endeavor, we have preset the following power-management features to take effect when your computer has been inactive for a
specified duration:
ENERGY STAR power-management features
Microsoft Windows 7
•Turns off the display: After 15 minutes
•Puts the computer to sleep: After 30 minutes
To awaken your computer from a display sleep mode, press any key on your keyboard. If the system has entered a deep-sleep
mode, please press the power button to wake up the system. For more information about these settings, refer to your Windows Help
and Support information system.
Agency Approvals
UL, cUL
Other specific Country Approvals may apply. Please see product certification label.
This document applies to regulatory model: INF5520
Input ratings: AC 100-240V, 7.5A, 50-60Hz
InFocus reserves the right to alter product offerings and specifications at any time without notice.

Contents
Declaration of Conformity ..................................................................................................................................... 1
Contents ................................................................................................................................................................ 3
Safety Considerations ............................................................................................................................................ 4
What’s Included..................................................................................................................................................... 6
Setup ..................................................................................................................................................................... 7
Attaching the Sound Bar ...........................................................................................................................................7
Installing the Feet......................................................................................................................................................9
Attaching the HD Video Conferencing Camera .......................................................................................................10
Setting up the Wireless Mouse and Keyboard.........................................................................................................11
Connecting to Other Devices ...................................................................................................................................12
Connecting AC Power ..............................................................................................................................................13
Turning Mondopad™ On/Off...................................................................................................................................14
Accessing the Installer’s Guide............................................................................................................................. 14
Limited Warranty................................................................................................................................................. 15

Page 4 Safety Considerations
Safety Considerations
•This tablet is very heavy and should be moved and installed by at least two individuals. Do not attempt to move or install
the tablet yourself, otherwise injury and/or damage may occur.
•When moving the tablet, always hold the tablet firmly using the side and bottom bezels. Do not hold the top bezel.
•When moving the INF5520 carton, do not tilt or invert the carton. Always keep it in an upright orientation.
•Disconnect all accessories and cables before moving the tablet.
•If the tablet is installed against the wall, maintain a distance of at least 1.98” (5cm) between the tablet and the wall to
provide adequate ventilation.
•Refer to this guide for proper startup and shutdown procedures.
•Follow all warnings and cautions in this manual and on the tablet.
•Locate the tablet at least 4' (1.2m) away from heating and cooling vents.
•Do not block ventilation openings. Locate the tablet in a well-ventilated area without obstructions to intake or exhaust
vents.
•Do not install or use the tablet or sound bar near any heat sources such as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce heat.
•Do not place the tablet in direct sunlight, humid, greasy or dusty places or in places where the tablet may come into
contact with rain, smoke or steam.
•The tablet should not be used with the power cord near water, for instance, near a bathtub, washbowl, kitchen sink or
swimming pool, etc.
•Do not use any components of the tablet, including the sound bar, near water. Warning: To reduce the risk of fire or
electric shock, do not expose this equipment or any component of this equipment to rain or moisture.
•Do not drop the tablet.
•Do not spill liquid on the tablet. Spilled liquid may damage the tablet.
•WARNING: This apparatus must be securely attached to the floor/wall per installation instructions. Tipping, shaking, or
rocking the machine may cause injury or death.
•The disconnect device shall remain readily operable.
•No naked flame source, such as lighted candles, should be placed on the apparatus.
•Use the power cord provided. Connect the power cord to a receptacle with a protective safety (earth) ground terminal. A
surge-protected power strip is recommended. Do not overload wall outlets.
•It is recommended that the Class 1 tablet be grounded.
•Do not install the tablet in places subject to mechanical vibration.
•Do not place the tablet on an unstable surface, which could result in serious personal injuries and tablet damage. When
mounting the tablet to a stand, be sure to following the manufacturer’s instructions. Use only the mounting hardware
recommended by the manufacturer.
•When disconnecting the power cord, hold the plug, not the cord.
•Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point
where they exit from the tablet.
•Unplug the tablet if you are not going to use it for an extensive period of time.
•Unplug the tablet if you need to clean it with the included microfiber cleaning cloth. The screen may be wiped with the
cleaning cloth when the power is off. Never use alcohol, solvents or ammonia-based liquids on this product.
•Wash hands after handling the cables supplied with this product.

Safety Considerations Page 5
•The tablet remote control, mouse and keyboard use batteries. Make sure the batteries’ polarity (+/-) is aligned correctly.
Dispose of used batteries in accordance with local disposal laws.
•Only use properly rated wall and stand mounting hardware that meet this product’s specifications and follow the
manufacturer installation instructions. The warranty does not cover any damage caused by use of improperly rated
mounting hardware or from improper installation.
•Refer all service to qualified service personnel. Do not remove the cover or back. Servicing your own tablet can be
dangerous to you and will void the warranty.
•Only use replacement parts specified by InFocus. Unauthorized substitutions may result in fire, electrical shock or injury
and may void the warranty.
•When mounting the tablet to a wall, metric 8 (12mm) screws must be used. In addition, the mounting interface should
comply with the UL1678 standard in North America. The mounting means should be strong enough to bear the weight of
the monitor (approximately 114.2 lbs/51.8 kg without the stand).
•Follow these instructions to help ensure image quality over the life of the tablet. Failure to follow these instructions may
affect the warranty.
•Hg – Lamp contains mercury. Manage in accordance with local disposal
laws. See www.lamprecycle.org.
•Lithium Battery (in PC Box) Caution: There is a risk of explosion if the battery is replaced by an incorrect type. The
battery should only be replaced with an identical or equivalent type of battery as recommended by the manufacturer.
Dispose of used batteries in accordance with local disposal laws.

Page 6 What’s Included
What’s Included
Camera
Remote control
(batteries not included)
1920 x 1080 Mondopad™
collaboration tablet
Thumb screws
(set of four)
Security tool
USB cable, 3M
(Type A to B)
Cleaning cloth
Power cord
Documentation
VGA cable, 4M
Feet
(set of two)
Sound bar
Thumb screws
(set of four)
Mounting brackets
(2 small and 1 large)
Power cords
(varies per country)
Feet spacers
(set of two)
M6 Screws
(set of six)
These items are
shipped in a
separate box
These items are
shipped in a
separate box
Wireless Keyboard & Mouse*
(batteries not included)
Stylus**
*Not included for all countries. For setup purposes, a keyboard and mouse are recommended. For additional
accessory options, such as stands, carts and wall mounts, see the InFocus website (www.infocus.com/store) or your
local dealer.** The stylus was added as a standard accessory to INF5520 serial number BJEE14900912 and later.

Setup Page 7
NOTE: If you are not attaching the sound bar, proceed to the next section, “Installing the Feet” on page 9.
Setup
Attaching the Sound Bar
1. Carefully place your tablet face-down on a clean, cushioned surface with the top edge hanging off
of the cushioned surface by 4-5” (10-13cm). Do NOT place the INF5520 on its back.
2. Attach the two small rectangular brackets to the sound bar with the provided screws as shown
below.
3. Remove four screws from the back of Mondopad as shown below.

Page 8 Setup
4. Align the rectangular brackets with the screw holes on the tablet and using the screws from Step
3, secure the sound bar against the bottom edge of the tablet.
5. Connect one end of the AC power cord to the AC In jack on the back of the sound bar.
6. Connect the other end of the AC power cord to the AC Out jack on the Bottom Connector Panel
of the tablet.
7. Plug the sound bar’s audio cable into the Audio Out (RCA R/L) jack on the Side Connector Panel
located on the back of the tablet.
8. Turn the power switch ON.
9. Route the power cord and audio cable through the large bracket and align the bracket against the
back side of the tablet and sound bar.
10. Fasten the bracket securely to the tablet and sound bar with the four remaining screws.
Power Switch

Setup Page 9
Installing the Feet
1. If you have not already done so, carefully place your tablet face-down on a clean, cushioned
surface with the top edge hanging off of the cushioned surface by 4-5” (10-13cm). Do NOT place
the INF5520 on its back.
2. Remove the tablet feet slot covers with a Philips screwdriver. Discard or save for future use.
3. Slide the feet into the slots provided (the longer side of the feet point toward the front of the
tablet), then secure the legs to the tablet with the provided screws.
4. Using the handles on the back of the tablet, lift the tablet upright.
Secure the legs here when the
sound bar is not being attached.
(The spacers are not used.)
Use the included spacers and
secure the legs here, when
attaching the sound bar.
Front View

Page 10 Setup
For additional accessory options, such as stands, carts and wall mounts, see the InFocus website
(www.infocus.com/store) or your local dealer.
Attaching the HD Video Conferencing Camera
1. Remove the plastic film from the camera lens.
2. Align the camera bracket with the screw holes on the top edge of the backside of the tablet and
then secure the camera to the tablet with the two provided thumb screws.
3. Plug the USB cable into an available USB slot on the back of the tablet.
4. Manually tilt and pan the camera (+/- 40°) as desired.
WARNINGS:
•This tablet is very heavy and should be moved by at least two individuals.
•Three screw holes have been included in each leg to allow you to adjust the height of the
tablet. Regardless of the height, you must use two of the screw holes in each leg. Failure to do
so may result in the screw begin sheared off and the leg collapsing.
•When mounting the tablet to a wall, metric 8 (12mm) screws must be used. In addition, the
mounting interface should comply with the UL1678 standard in North America. The mounting
means should be strong enough to bear the weight of the monitor (approximately 114.2
lbs/51.8 kg without the stand).

Setup Page 11
Setting up the Wireless Mouse and Keyboard
Note: The wireless mouse and keyboard is not included as a standard accessory for some countries. For
initial setup and/or configuration, it may be easier to use a mouse and keyboard. Any standard wired or
wireless mouse or keyboard connected through the Mondopad USB ports is supported by Mondopad.
Wireless Mouse
1. Turn the mouse over and remove the battery cover.
2. Remove the USB dongle from its holder in the battery compartment
of the mouse.
3. Plug it into a free USB-A port on the Bezel Connector Panel of the
tablet. You may be asked to go online to find the necessary drivers. If
you are warned that the drivers have not been tested for compatibility,
click Continue installation to finish.
4. Insert two (2) AAA batteries (not included) into the mouse by aligning the +
and – end of the batteries as indicated and sliding them in place.
5. Replace the cover and switch the mouse on using the slide switch
next to the battery bay.
Wireless Keyboard
1. Turn the keyboard over and open the battery cover.
2. Insert two (2) AAA batteries (not included) into the keyboard, by aligning the + and – ends of the
batteries and sliding them in place.
3. Replace the cover.
4. Press the CONNECT button and hold it for one second to allow the keyboard to bind with the
dongle.

Page 12 Setup
Connecting to Other Devices
A full range of digital and analog video inputs and audio source devices can be connected to the
connection panels on the back and side of Mondopad™, if desired. Available jacks include: HDMI®(2),
VGA, Component (RCA), S-Video, Composite, RS232, Audio in RCA (1 – R/L), Audio in 3.5mm (1), Audio
Out (1 – R/L), RJ45 (2), USB-B (1) and USB-A (6).
Bottom Connector Panel
Side Connector
Panel
Bezel Connector
Panel

Setup Page 13
Bezel Connector Panel
Side Connector Panel
Bottom Connector Panel
Connecting AC Power
1. Connect one end of the AC power cord to the AC In jack on the back of the tablet.
2. Connect the other end of the AC power cord to an AC outlet.
3. Press the power switch on the Bottom Connector Panel ON. (The LED on the front of the
Mondopad™ tablet displays red.)
NOTES:
•Your tablet should only be operated from the power source indicated on the label.
•Always unplug the AC power cord from the power outlet when you are not using your tablet
for an extended period of time.
Power button USB-A jacks USB-B jack
Audio In (L/R)
RS232
RJ45
USB-A
Audio Out (L/R)
(for Sound Bar)
Keypad
Antennas
Power LED
Audio In (3.5mm)
Power switch
HDMI®
VGA
Component
(YPbPr)
AC Power In
AC Power Out
S-video
Composite
PC Reset
button

Page 14 Accessing the Installer’s Guide
Turning Mondopad™ On/Off
1. Verify that the power cord is connected to a power outlet and that the power switch on the Bottom
Connector Panel is ON.
2. Press the Power button located on either:
a. the remote
b. the right side of the tablet
c. or the back of the tablet on the PC box.
The front LED turns green.
3. Press the Power button again to put the tablet into Standby. The front LED turns red. You can
also put your tablet to sleep using the keyboard. The front LED turns orange.
Notes:
•If the tablet becomes locked and does not respond to normal power down procedures, the tablet
can be powered down by pressing and holding the PC box Power button (located on the back of
the tablet) for 7-8 seconds.
Accessing the Installer’s Guide
To complete the setup of this product and the Mondopad Collaboration software, please download the
Installer’s Guide located at www.infocus.com/INF5520docs.
NOTE: Mondopad documentation is available in multiple languages. To download, go to
www.infocus.com/INF5520docs.

Limited Warranty Page 15
Limited Warranty
InFocus Limited Warranty For InFocus Branded Hardware Products Only
LIMITED WARRANTY.InFocus’s warranty obligations for the hardware products are limited to the terms set forth herein. InFocus
warrants the InFocus-branded hardware products against defects in materials and workmanship under normal use for a period
outlined in the Limited Warranty Periods section below from the date of retail purchase by the original end-user purchaser
(“Warranty Period”). The Warranty Period starts on the date of purchase. Your dated sales or delivery receipt, showing the date of
purchase of the product, is your proof of the purchase date. You may be required to provide proof of purchase and proof that the
product was purchased new as a condition of receiving warranty service. If a hardware defect arises and a valid claim is received
within the Warranty Period, at its option and to the extent permitted by law, InFocus will either (1) repair the hardware defect at no
charge, using new parts or refurbished parts that are equivalent to new in performance and reliability, (2) exchange the product with
a product that is new or refurbished that is equivalent to new in performance and reliability and is at least functionally equivalent to
the original product, or (3) refund the purchase price of the product. InFocus may request that you replace defective parts with
customer-installable new or refurbished parts that InFocus provides in fulfillment of its warranty obligation (“Customer Self Repair”).
A replacement product or part, including a Customer Self Repair part that has been installed in accordance with instructions
provided by InFocus, assumes the remaining warranty of the original product or ninety (90) days from the date of replacement or
repair, whichever provides longer coverage. When a product or part is exchanged, any replacement item becomes your property
and the replaced item becomes InFocus’s property. Parts provided by InFocus in fulfillment of its warranty obligation must be used
in products for which warranty service is claimed. When a refund is given, the product for which the refund is provided must be
returned to InFocus and becomes InFocus’s property. This is your exclusive remedy for defective products.
Limited Warranty Periods are as follows:
LCD Thin Tablet Device (including embedded PC), Camera, Remote, and Sound Bar Product Limited Warranty
Period: one (1) year from date of purchase.
Accessory Product Limited Warranty Period: ninety (90) days from date of purchase.
The Accessory Product Limited Warranty covers the accessory items only and excludes normal wear and tear.
Remanufactured Products and Software Products are exempt from the foregoing Limited Warranty. Please refer to the appropriate
Remanufactured Product Limited Warranty or Software Product Limited Warranty for applicable Warranty information.
EXCLUSIONS AND LIMITATIONS.This Limited Warranty applies only to the hardware products manufactured by or for InFocus,
and sold by InFocus, its worldwide subsidiaries, authorized resellers or country distributors, that can be identified by the “InFocus”
trademark, trade name, or logo affixed to it, and to required firmware. The Limited Warranty does not apply to any non-InFocus
hardware products or peripherals external to the InFocus-branded hardware products (including but not limited to external storage
subsystems, displays, printers, speakers or other peripherals), or to any software applications or programs, even if packaged or sold
with the InFocus hardware. Manufacturers, suppliers, or publishers of products, software or peripherals, other than InFocus, may
provide their own warranties to the end user purchaser, but InFocus, in so far as permitted by law, provides their products “AS IS”
without the InFocus Limited Warranty. Software distributed by InFocus with or without the InFocus brand name (including, but not
limited to system software) is not covered under this Limited Warranty. Refer to the licensing agreement accompanying the software
for details of your rights with respect to its use.
InFocus does not warrant that the operation of the products will be uninterrupted or error-free. InFocus is not responsible for
damage arising from failure to follow instructions relating to the products’ use.
INFOCUS IS NOT RESPONSIBLE FOR DAMAGE TO OR LOSS OF ANY PROGRAMS, DATA, OR REMOVABLE STORAGE
MEDIA. INFOCUS IS NOT RESPONSIBLE FOR THE RESTORATION OR REINSTALLATION OF ANY PROGRAMS OR DATA
OTHER THAN SOFTWARE INSTALLED BY INFOCUS WHEN THE PRODUCT IS MANUFACTURED.
To enable InFocus to provide the best possible support and service during the Limited Warranty Period, you will be required to:
Maintain a proper and adequate environment, and use the InFocus hardware products in accordance with the instructions
furnished.
Verify configurations, load most recent firmware, install software patches, run InFocus diagnostics and utilities, and
implement temporary procedures or workarounds provided by InFocus while InFocus works on permanent solutions.
Allow InFocus to keep resident on your systems or sites certain system and network diagnosis and maintenance tools to
facilitate the performance of warranty support (collectively referred to as “Proprietary Service Tools”); Proprietary Service
Tools are and remain the sole and exclusive property of InFocus.

Page 16 Limited Warranty
Additional Limitations:
Products external to the system processor (CPU) box, such as external storage subsystems, printers and other
peripherals, are covered by the applicable warranty for those products or options.
An effective repair does not necessarily require the replacement of a defective part. For example, cleaning the heads of a
floppy drive or updating revision levels of ROM BIOS on a PCA board are activities that in many instances deliver an
effective repair.
BIOS/Firmware upgrades are not covered under the Limited Warranty. Firmware that is an integral part of the option
hardware board is not automatically upgraded when new versions of firmware are released.
It is the responsibility of the customer to ensure that their software is compatible with the latest BIOS/firmware revision.
This Limited Warranty does not apply: (a) to consumable or expendable parts, such as batteries, or protective coatings
designed to diminish over time unless failure has occurred due to a defect in materials or workmanship; (b) to cartons,
carrying cases, shipping cases, external cabinets, accessories used in connection with the product; (c) to cosmetic
damage, including but not limited to scratches, dents, and broken plastic on ports; (d) to damage caused by use with non-
InFocus products; (e) to damage caused by accident, abuse, misuse, improper ventilation, smoke exposure,
contamination, improper or inadequate maintenance, cleaning or calibration, liquid contact, unusual physical or electrical
stress and/or power surges, virus infection, fire, earthquake, disaster, lightning or other external causes; (f) to damage
caused by operating the product outside the permitted or intended uses or usage parameters described by InFocus
(including burned monitor screens and incorrect input voltage); (g) to damage caused by service (including upgrades and
expansions) performed by anyone other than a representative of InFocus or an InFocus Authorized Service Provider
(“ASP”) or your own installation of customer-installable parts as instructed by InFocus; (h) to a product or part that has
been modified to alter functionality or capability without the written permission of InFocus (including use of an
unauthorized mount); (i) to defects caused by normal wear and tear or otherwise due to the normal aging of the product; (j)
to failure to follow maintenance procedures as outlined in the product user documentation including where a schedule is
specified for regular cleaning of certain parts (based on usage and environment); (k) to loss or damage in transit; or (l) if
the product is not used under normal operating conditions which are defined as use not in excess of 16 hours
continuously per day with a minimum 8 hour period of continuous rest in the powered off state; or (m) if any InFocus serial
number has been removed or defaced. In addition, LCD burn-in as a result of excessive display of static images on the
product is not covered under the terms of this Limited Warranty.
Important: Do not open the hardware products unless otherwise directed by InFocus for the purposes of a Customer Self
Repair (CSR). Opening the hardware products may cause damage that is not covered by this Limited Warranty. Only
InFocus or an ASP should perform service on the hardware products.
TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND
IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL, WRITTEN, STATUTORY, EXPRESS
OR IMPLIED. AS PERMITTED BY APPLICABLE LAW, INFOCUS SPECIFICALLY DISCLAIMS ANY AND ALL STATUTORY OR
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS. IF INFOCUS CANNOT LAWFULLY
DISCLAIM STATUTORY OR IMPLIED WARRANTIES THEN TO THE EXTENT PERMITTED BY LAW, ALL SUCH WARRANTIES
SHALL BE LIMITED IN DURATION TO THE DURATION OF THE EXPRESS WARRANTY AND TO THE REPAIR OR
REPLACEMENT SERVICE AS DETERMINED BY INFOCUS IN ITS SOLE DISCRETION. NO INFOCUS RESELLER, AGENT, OR
EMPLOYEE IS AUTHORIZED TO MAKE ANY MODIFICATION, EXTENSION, OR ADDITION TO THIS WARRANTY. IF ANY
TERM IS HELD TO BE ILLEGAL OR UNENFORCEABLE, THE LEGALITY OR ENFORCEABILITY OF THE REMAINING TERMS
SHALL NOT BE AFFECTED OR IMPAIRED.
EXCEPT AS PROVIDED IN THIS WARRANTY AND TO THE MAXIMUM EXTENT PERMITTED BY LAW, INFOCUS IS NOT
RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF
WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE;
LOSS OF REVENUE; LOSS OF ACTUAL OR ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS);
LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS; LOSS OF OPPORTUNITY; LOSS
OF GOODWILL; LOSS OF REPUTATION; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY
INDIRECT OR CONSEQUENTIAL LOSS OR DAMAGE HOWSOEVER CAUSED INCLUDING THE REPLACEMENT OF
EQUIPMENT AND PROPERTY, ANY COSTS OF RECOVERING, PROGRAMMING OR REPRODUCING ANY PROGRAM OR
DATA STORED IN OR USED WITH THE INFOCUS PRODUCT AND ANY FAILURE TO MAINTAIN THE CONFIDENTIALITY OF
DATA STORED ON THE PRODUCT. THE FOREGOING LIMITATION SHALL NOT APPLY TO DEATH OR PERSONAL INJURY
CLAIMS, OR ANY STATUTORY LIABILITY FOR INTENTIONAL AND GROSS NEGLIGENT ACTS AND/OR OMISSIONS.

Limited Warranty Page 17
INFOCUS DISCLAIMS ANY REPRESENTATION THAT IT WILL BE ABLE TO REPAIR ANY PRODUCT UNDER THIS
WARRANTY OR MAKE A PRODUCT EXCHANGE WITHOUT RISK TO OR LOSS OF PROGRAMS OR DATA.
LIMITATION ON BRINGING ACTION: NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO
PURCHASE THE PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION
HAS ACCRUED. GOVERNING LAW: ANY ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO
PURCHASE THE PRODUCT IS GOVERNED BY THE LAWS OF THE STATE OF OREGON, U.S.A. MANDATORY ARBITRATION
– ANY ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT IS SUBJECT
TO MANDATORY ARBITRATION.
ADDITIONAL RIGHTS. FOR CUSTOMERS, WHO ARE COVERED BY CONSUMER PROTECTION LAWS OR REGULATIONS
IN THEIR COUNTRY OF PURCHASE OR, IF DIFFERENT, THEIR COUNTRY OF RESIDENCE, THE BENEFITS CONFERRED
BY THIS WARRANTY ARE IN ADDITION TO ALL RIGHTS AND REMEDIES PROVIDED BY SUCH CONSUMER PROTECTION
LAWS AND REGULATIONS. THIS WARRANTY DOES NOT EXCLUDE, LIMIT OR SUSPEND ANY RIGHTS OF CONSUMERS
ARISING OUT OF NONCONFORMITY WITH A SALES CONTRACT. SOME COUNTRIES, STATES AND PROVINCES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY OR CONDITION MAY LAST, SO THE LIMITATIONS OR EXCLUSIONS DESCRIBED
BELOW MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS THAT VARY BY COUNTRY, STATE OR PROVINCE. INFOCUS, THE WARRANTOR UNDER THIS LIMITED
WARRANTY, IS IDENTIFIED AT THE END OF THIS DOCUMENT.
EXTENDED WARRANTIES. InFocus extended product warranties are available for an additional charge. For further information on
InFocus extended product warranties, please contact InFocus or your product reseller.
OBTAINING WARRANTY SERVICE.Please access and review the online help resources located at www.infocus.com/support
before seeking warranty service. If the product is still not functioning properly after making use of these resources, please contact
InFocus Technical Support or, if applicable, an ASP using the information provided below. When contacting InFocus via telephone,
other charges may apply depending on your location. When calling, InFocus Technical Support or an ASP will help determine
whether your product requires service and, if it does, will inform you how InFocus will provide it. You must assist in diagnosing
issues with your product and follow InFocus’s warranty processes. InFocus may restrict service to the country where InFocus or its
Authorized Distributors originally sold the hardware product. InFocus will provide warranty service either (i) at an ASP location,
where service is performed at the location, or the ASP may send the product to an InFocus repair service location for service, (ii) by
sending you prepaid way bills (and if you no longer have the original packaging, InFocus may send you packaging material at your
cost) to enable you to ship the product to an InFocus repair service location, or (iii) by sending you customer-installable new or
refurbished replacement parts to enable you to conduct Customer Self Repair, or (iv) by exchanging the product for a new or
refurbished replacement.
Customer Self Repair
InFocus products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for greater flexibility
in performing defective parts replacement. If during the diagnosis period, InFocus identifies that the repair can be accomplished by
the use of a CSR part, InFocus will ship that part directly to you for replacement. There are two categories of CSR parts:
Parts for which customer self repair is mandatory. If you request InFocus to replace these parts, you will be charged for
the travel and labor costs of this service.
Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you
require that InFocus replace them for you, this may be done at no additional charge under the type of warranty service
designated for your product.
Based on availability and where geography permits, InFocus will attempt to ship CSR parts out the next business day. Customer
receipt will vary based upon the actual part, customer location and shipping method. Next day, same-day or four-hour delivery may
be offered at an additional charge where geography permits. If assistance is required, you can call the InFocus Technical Support
Center and a technician will help you over the phone. InFocus specifies in the materials shipped with a replacement CSR part
whether a defective part must be returned to InFocus. In cases where it is required to return the defective part to InFocus, you must
ship the defective part back to InFocus within a defined period of time, normally five (5) business days, and clearly display the

Page 18 Limited Warranty
Return Material Authorization (RMA#) on the outside of the shipping carton or a similar package affording an equal degree of
protection. The defective part must be returned with the associated documentation in the provided shipping material. Failure to
return the defective part may result in InFocus charging you for the replacement. With a Customer Self Repair, InFocus will pay all
shipping and part return costs and determine the courier/carrier to be used.
InFocus may utilize a doorstep swap process, which involves an InFocus delivery person delivering the replacement product or CSR
part to the Customer and picking up the defective product or part at the time of delivery for return to InFocus. Upon receipt of the
replacement product or part, the original product or part becomes the property of InFocus and you agree to follow instructions,
including arranging the return of original product or part to InFocus in a timely manner. When providing a product exchange or
Customer Self Repair (CSR) part requiring the return of the original product or part, InFocus may require a credit card authorization
as security for the retail price of the replacement product or part and applicable shipping costs. When returning product to InFocus,
a Return Material Authorization Number (RMA #) is required and must be clearly displayed on the outside of the shipping carton or a
similar package affording an equal degree of protection. Service options, parts availability and response times may vary according
to the country in which service is requested. Service options are subject to change at any time. You may be responsible for shipping
and handling charges if the product cannot be serviced in the country in which service is requested. If you seek service in a country
that is not the country of original purchase, you will comply with all applicable import and export laws and regulations and be
responsible for all custom duties, V.A.T. and other associated taxes and charges. Where international service is available, InFocus
may repair or exchange defective products and parts with comparable products and parts that comply with local standards. In
accordance with applicable law, InFocus may require that you furnish proof of purchase details and/or comply with registration
requirements before receiving warranty service. Resources with more details on this and other matters on obtaining warranty
service are described below.
PRIVACY.InFocus will maintain and use customer information in accordance with the InFocus Privacy Policy available at
www.Infocus.com/privacy and InFocus’s applicable legal obligations.
BACKUP. If your product is capable of storing software programs, data and other information, you should protect its contents
against possible operational failures. Before you deliver your product for warranty service it is your responsibility to keep a separate
backup copy of the contents, remove all personal information and data that you want to protect and disable any security passwords.
THE CONTENTS OF YOUR PRODUCT WILL BE DELETED AND THE STORAGE MEDIA REFORMATTED IN THE COURSE OF
WARRANTY SERVICE. Your product or a replacement product will be returned to you as your product was configured when
originally purchased, subject to applicable updates. InFocus may install system software updates as part of warranty service that will
prevent the hardware from reverting to an earlier version of the system software. Third party applications installed on the hardware
may not be compatible or work with the hardware as a result of the system software update. You will be responsible for reinstalling
all other software programs, data and passwords. Recovery and reinstallation of software programs and user data are not covered
under this Limited Warranty.
RESOURCES. Support and service information including Authorized Distributor and Authorized Service Provider locations is
available at: www.infocus.com/support.
InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, OR 97223-8368 USA
© 2011 InFocus Corp. All rights reserved. InFocus and the InFocus logo are trademarks of InFocus Corp., registered in the U.S. and
other countries.