inforce WML Series User manual

USER MANUAL:
WML SERIES
WML White
WML White/IR
WMLx White
WMLx White/IR
INFORCE-MIL.COM
MAINTENANCE
CLEANING INSTRUCTIONS
WML requires minimal maintenance from time-to-time.
1. Clean threads (1) of head and body with alcohol swab.
2. Clean contact surfaces (2) of head and body with alcohol swab.
3. Apply thin coat of silicon-based lubricant to rubber o-ring (3)
of head. DO NOT USE A PETROLEUM-BASED LUBRICANT.
If light becomes dirty from dust, sand, etc... tighten head fully,
rinse with water, and dry with a soft cloth.
(1)
(1)
(2)
(2) (3)
For warranty information please visit www.inforce-mil.com
Follow the cleaning procedures as set
forth in the manual of your rearm.
Always remove the INFORCE WML /
WMLx from the rearm when performing
maintenance, cleaning, or replacing the
battery. Do not operate the INFORCE
WML / WMLx around ammable/
combustible materials or in ammable
atmospheres involving evaporated
gasolines, or where paints, solvents, or
other ammable liquids are stored.
FIREARM & WML / WMLx SAFETY WARNING
Your INFORCE WML / WMLx is designed for use with destructive weapon
systems. Improper operation or misuse of the INFORCE WML / WMLx with
these weapons may lead to personal injury or death of the operator or others
within the weapon’s range. Safe rearms handling procedures must be
practiced at all times.
Before handling a weapon with the INFORCE WML / WMLx attached, read and
understand the entire contents of the weapon’s manual and the INFORCE
WML / WMLx instructions, especially the safety precautions and procedures
for safe rearms handling. Always practice safe rearms handling techniques.
Failure to comply with correct safety precautions and safe rearms handling
techniques may result in serious injury, damage to property, or death.
- Never point the rearm at anything or anyone that you don’t intend to shoot.
- Always keep your nger outside the trigger guard and o the trigger until
you are ready to re the weapon.
- Always verify that the chamber of the weapon is empty or “clear” before
attempting to mount or dismount the INFORCE WML.
USER INFORMATION

FUNCTIONS OPERATION
WML WHITE & WMLx WHITE
LIGHT OPERATION
Constant
With LED lever pointing forward in Position (A)
press button once to turn on constant white
light. Pressing button again or moving the lever
from Position (A) to Position (B) will turn the
light o.
In constant mode, momentary is also available.
Press and hold button for more than ½ second
to turn light on. Release pressure o button to
turn light o.
Momentary
With LED lever pointing backward in Position (B)
press and hold button to turn light on. Release
pressure o button to turn light o.
Strobe
With the LED lever pointing forward in Position (A)
quickly press button twice to activate strobe.
Pressing button again or moving lever from
Position (A) to Position (B) will turn light o.
LOCKOUT SYSTEMS
DISABLING STROBE
BATTERY REPLACEMENT
WML WHITE/IR & WMLx WHITE/IR
LIGHT OPERATION
Constant (IR)
With LED lever pointing backward in Position (B)
press button once to turn on constant IR light.
Pressing button again or moving lever from
Position (B) to Position (A) will turn light o.
Momentary (IR)
With LED lever pointing backward in Position (B)
press and hold button to turn light on. Release
pressure o button to turn light o.
A
B
(white indicator visible)
There are two lockout methods to prevent
accidental discharge when carrying light.
1. Safety lever protects activation of button.
Li lever up 90˚to cover button.
2. Unscrew head ¼ rotation.
1. Unscrew head ¼ rotation to lockout position.
2. Press and hold button.
3. While holding button, tighten clockwise back into place.
Once tightened, release button and strobe will be disabled.
Repeat steps 1 - 3 to enable strobe.
1. Unscrew head to remove it from body.
2. Insert one battery (WML units), or two
batteries (WMLx units) into body. Positive
(+) side rst as shown in the gure below.
3. Screw head back into body.
MOUNTING WML & WMLx TO RAIL
1. Turn clamp screw
counterclockwise
until completely
loosened.
To dismount light, turn clamp screw counterclockwise until completely loosened.
Push clamp toward body and li o rail.
2. Push clamp toward
body and place onto
rail. Release pressure
o clamp once on rail.
3. Finger tighten screw
clockwise until
secured on rail.
DO NOT USE TOOLS.
Head (2)
Lockout Lever (1)
+
-
WARNING: Lithium batteries can explode or cause burns if
recharged, shorted, disassembled, exposed to water or high
temperatures of re. Follow battery manufacturer’s guidelines
for safe storage, use and disposal. If light has been submerged,
dry exterior of light prior to replacing batteries. Fresh and salt
water will damage internal electronics and batteries.
Do not use counterfeit or inferior quality batteries, as they
do not meet safety and performance standards and may
cause personal and property damage. Ensure safety and
performance by purchasing established brands, such as:
Duracell, Energizer, or Panasonic.