Inglis IFR8200 User manual

240-VOLT
ELECTRIC DRYER
Use & Care Guide
For assistance, installation or service, call: 1-800-807-6777
or visit our website at...www.inglis.ca
SÉCHEUSE ÉLECTRIQUE
240 VOLTS
Guide d’utilisation
et d’entretien
Pour assistance, installation ou service, composez le 1-800-807-6777
ou visitez notre site web à www.inglis.ca
Table of Contents/Table des matières .................. 2
8577217

2
TABLE OF CONTENTS
DRYER SAFETY..............................................................................3
INSTALLATION REQUIREMENTS................................................4
Tools and Parts ............................................................................4
Options.........................................................................................4
Location Requirements................................................................4
Electrical Requirements ...............................................................6
Venting Requirements..................................................................6
INSTALLATION INSTRUCTIONS..................................................8
Plan Vent System.........................................................................8
Install Vent System.......................................................................9
Connect Vent................................................................................9
Level Dryer ...................................................................................9
Complete Installation .................................................................10
DRYER USE ..................................................................................11
Starting Your Dryer.....................................................................11
Stopping and Restarting............................................................11
Changing Cycles and Temperatures .........................................11
Controls......................................................................................12
Drying, Cycle and Temperature Tips .........................................12
Cycles.........................................................................................13
DRYER CARE ...............................................................................14
Cleaning the Dryer Location ......................................................14
Cleaning the Lint Screen............................................................14
Cleaning the Dryer Interior .........................................................14
Cleaning the Control Panel ........................................................15
Removing Accumulated Lint......................................................15
Vacation and Moving Care.........................................................15
TROUBLESHOOTING ..................................................................15
ASSISTANCE OR SERVICE.........................................................17
WARRANTY ..................................................................................18
TABLE DES MATIÈRES
SÉCURITÉ DE LA SÉCHEUSE ....................................................19
EXIGENCES D’INSTALLATION...................................................20
Outillage et pièces......................................................................20
Options .......................................................................................20
Emplacement d’installation .......................................................20
Spécifications électriques ..........................................................22
Exigences concernant l'évacuation ...........................................23
INSTRUCTIONS D’INSTALLATION.............................................24
Planification du système d’évacuation ......................................24
Installation du conduit d’évacuation ..........................................25
Conduit d'évacuation .................................................................25
Mise àniveau de la sécheuse ....................................................26
Achever l'installation ..................................................................26
UTILISATION DE LA SÉCHEUSE................................................27
Mise en marche de la sécheuse ................................................27
Arrêt et remise en marche..........................................................27
Modification des programmes et températures ........................27
Commandes...............................................................................28
Conseils pour le séchage, les programmes et la température..29
Programmes...............................................................................29
ENTRETIEN DE LA SÉCHEUSE.................................................30
Nettoyage de l'emplacement de la sécheuse ...........................30
Nettoyage du filtre àcharpie......................................................30
Nettoyage de l'intérieur de la sécheuse.....................................31
Nettoyage du panneau de commande......................................31
Comment enlever la charpie accumulée ...................................31
Précautions àprendre pour les vacances et avant
un déménagement .....................................................................31
DÉPANNAGE.................................................................................32
ASSISTANCE OU SERVICE.........................................................34
GARANTIE.....................................................................................35

3
DRYER SAFETY
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
WARNING:
■ Read all instructions before using the dryer.
■ Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch fire.
■ Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
■ Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
■ Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
■ Do not reach into the dryer if the drum is moving.
■ Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
■ Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
■ Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
■ Clean lint screen before or after each load.
■ Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
SAVE THESE INSTRUCTIONS
■ The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
■ Do not install or store the dryer where it will be exposed
to the weather.
■ Do not tamper with controls.
■ See installation instructions for grounding requirements.

4
INSTALLATION REQUIREMENTS
Tools and Parts
Tools needed
Gather the required tools and parts before starting installation.
Read and follow the safety instructions provided with any tools
listed here.
Parts supplied
Remove parts package from the dryer drum. Check that all parts
listed are included.
Parts needed
Check local codes, existing electrical supply and venting, and
see “Venting Requirements”and “Electrical Requirements”
before purchasing parts.
Mobile home installations require metal exhaust system
hardware. For ordering information, please refer to the
“Assistance or Service”section of this manual. You may also
contact the dealer from whom you purchased your dryer.
Options
Pedestal
You may order a pedestal separately for this dryer. This pedestal
will add about 12" (30.48 cm) to the height of your unit for a total
height of approximately 45" (114.3 cm).
To order, call the dealer from whom you purchased your dryer or
refer to the “Assistance or Service”section of this manual. Ask
for Model Number LAB0050PQ.
Stack Kit
Are you planning to stack your washer and dryer? To do so you
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or
refer to the “Assistance or Service”section of this manual. Ask
for Part Number 8182452.
Location Requirements
You will need
■A location that allows for proper exhaust installation. See
“Venting Requirements.”
■A separate 30-amp circuit.
■Flat-blade screwdriver
■Adjustable wrench
■T20 TORX®† screwdriver
■Caulking gun and
compound (for installing
new exhaust vent)
■Tin snips (new vent
installations)
■Wood block
■Level
■Vent clamps
Coupling
†®TORX is a registered trademark of Textron Innovations Inc.
Optional pedestal
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.

5
■A grounded electrical outlet located within 2 ft (61 cm) of
either side of the dryer. See “Electrical Requirements.”
■A sturdy floor to support the dryer weight (dryer and load) of
115 lbs (52 kg). The combined weight of a companion
appliance should also be considered.
■A level floor with a maximum slope of 1" (2.5 cm) under entire
dryer.
Do not operate your dryer at temperatures below 45ºF (7ºC). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. Drying times can be extended.
The dryer must not be installed or stored in an area where it will
be exposed to water and/or weather.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
Installation Clearances
The location must be large enough to allow the dryer door to
open fully.
Dryer Dimensions
*Most installations require a minimum 5½" (14.0 cm) clearance
behind the dryer for the exhaust vent with elbows. See “Venting
Requirements.”
Minimum installation spacing for recessed area and closet
installation
The following dimensions shown are for the minimum spacing
allowed when the dryer is to be operated with, or without, the
Stack Kit. To purchase a Stack Kit, see “Assistance or Service.”
■Additional spacing should be considered for ease of
installation and servicing.
■Additional clearances might be required for wall, door and
floor moldings.
■Spacing of 1" (2.5 cm) on all sides of the dryer is
recommended to reduce noise transfer.
■For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
■Companion appliance spacing should also be considered.
Recessed or closet installation - Dryer only
Recessed or closet installation - Stacked with stack kit
(Accessory)
Mobile Home - Additional Location Requirements
This dryer is suitable for mobile home installations.
The installation must conform to the Manufactured Home
Construction and Safety Standard CAN/CSA-Z240 MH.
Mobile home installations require:
■Metal exhaust system hardware, which is available for
purchase from your dealer.
■Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
33 ¼"
(84.45 cm)
23 ³⁄₈ "
(59.37 cm)
39"
(99.1 cm) 23 ¼"
(60.3 cm)
*
A. Side view - closet or confined area
B. Recessed area
C. Closet door with vents
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
B
A
3"
(7.6cm)
14"
(35.6cm)
18"(45.7cm)
1"
(2.5 cm) 1"
(2.5 cm)
48 in.2
(310 cm2)
24 in.2
(155 cm2)
3"
(7.6 cm)
3"
(7.6 cm)
C
1" (2.5 cm)
DRYER
WASHER
(30.5 cm)
12"
1" (2.5 cm)
1" (2.5 cm)
ABC
1" (2.5 cm)
48 in.2
(310 cm2)
24 in.2
(155 cm2)
3"
(7.6 cm)
3"
(7.6 cm)
3" (7.6 cm)

6
Electrical Requirements
It is your responsibility
■To contact a qualified electrical installer.
■To be sure that the electrical connection is adequate and in
conformance with the Canadian Electrical Code, C22.1-latest
edition and all local codes. A copy of the above codes
standard may be obtained from: Canadian Standards
Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3
CANADA.
■To supply the required 4 wire, single phase, 120/240 volt,
60 Hz., AC only electrical supply on a separate 30-amp
circuit, fused on both sides of the line. A time-delay fuse or
circuit breaker is recommended. Connect to an individual
branch circuit.
■This dryer is equipped with a CSA International Certified
Power Cord intended to be plugged into a standard 14-30R
wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure
wall receptacle is within reach of dryer’s final location.
4-wire receptacle 14-30R
If using a replacement power supply cord, it is recommended
that you use Power Supply Cord Replacement Part Number
3393639.
For further information, please reference the service
numbers located in the “Assistance or Service”section of this
manual.
Venting Requirements
WARNING: To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, or a concealed space of a building.
If using an existing vent system
■Clean lint from the entire length of the system and make sure
exhaust hood is not plugged with lint.
■Replace any plastic or metal foil vent with rigid or flexible
heavy metal vent.
■Review Vent system chart. Modify existing vent system if
necessary to achieve the best drying performance.
WARNING
Electrical Shock Hazard
Plug into a grounded 4 prong outlet.
Failure to do so can result in death or electrical shock.
For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction
or breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current. This
dryer is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative or
personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with the
dryer: if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
WARNING
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.

7
If this is a new vent system
Vent material
■Use a heavy metal vent. Do not use plastic or metal foil vent.
■4" (10.2 cm) heavy metal exhaust vent and clamps must be
used.
Rigid metal vent
■For best drying performance, rigid metal vents are
recommended.
■Rigid metal vent is recommended to avoid crushing and
kinking.
Flexible metal vent
■Flexible metal vents are acceptable only if accessible for
cleaning.
■Flexible metal vent must be fully extended and supported
when the dryer is in its final position.
■Remove excess flexible metal vent to avoid sagging and
kinking that may result in reduced airflow and poor
performance.
■Do not install flexible metal vent in enclosed walls, ceilings or
floors.
Elbows
45°elbows provide better airflow than 90°elbows.
Clamps
■Use clamps to seal all joints.
■Exhaust vent must not be connected or secured with screws
or other fastening devices that extend into the interior of the
duct. Do not use duct tape.
Exhaust
Recommended hood styles are shown here.
The angled hood style (shown here) is acceptable.
■An exhaust hood should cap the vent to keep rodents and
insects from entering the home.
■Exhaust hood must be at least 12" (30.5 cm) from the ground
or any object that may be in the path of the exhaust (such as
flowers, rocks or bushes, snow line, etc.).
■Do not use an exhaust hood with a magnetic latch.
4" (10.2 cm) heavy metal exhaust vent
Good Better
Clamp
4"
10.2 cm A. Louvered hood style
B. Box hood style
4"
(10.2 cm)
4"
(10.2 cm)
B
A
4"
(10.2 cm)
2½"
(6.4 cm)
Improper venting can cause moisture and lint to collect
indoors, which may result in:
Moisture damage to woodwork, furniture, paint,
Housecleaning problems and health problems.
wallpaper, carpets, etc.

8
INSTALLATION INSTRUCTIONS
Plan Vent System
Choose your exhaust installation type
Recommended exhaust installations
Typical installations vent the dryer from the rear of the dryer.
Alternate installations for close clearances
Venting systems come in many varieties. Select the type best for
your installation. A close-clearance installation is shown below.
Refer to the manufacturer’s instructions.
Over-the-top Installation Kit Part Number 4396028 for close
clearance alternate installation is available for purchase. For
ordering information see “Assistance or Service.”
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.
Determine vent path
■Select the route that will provide the straightest and most
direct path outdoors.
■Plan the installation to use the fewest number of elbows and
turns.
■When using elbows or making turns, allow as much room as
possible.
■Bend vent gradually to avoid kinking.
■Use the fewest 90°turns possible.
A. Exhaust hood
B. Flexible metal vent or rigid metal vent
C. Elbow
WARNING
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
A
B
C
Over-the-top installation (also available with one offset elbow)

9
Determine vent length and elbows needed for best
drying performance
■Use the Vent system chart below to determine type of vent
material and hood combinations acceptable to use.
NOTE: Do not use vent runs longer than those specified in
the Vent system chart. Exhaust systems longer than those
specified will:
■Shorten the life of the dryer.
■Reduce performance, resulting in longer drying times and
increased energy usage.
The Vent system chart provides venting requirements that will
help to achieve the best drying performance.
Vent system chart
Install Vent System
1. Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
2. Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.
3. Run vent to dryer location. Use the straightest path possible.
See “Determine vent path.”Avoid 90ºturns. Use clamps to
seal all joints. Do not use duct tape, screws or other fastening
devices that extend into the interior of the vent to secure
vent.
Connect Vent
1. To protect the floor, use a large, flat piece of cardboard from
the dryer carton. Place cardboard under the entire bottom of
the dryer.
2. Slide the dryer on the cardboard until it is close to its final
location. Leave enough room to connect the exhaust vent.
3. Using the coupling supplied with the dryer, connect the
exhaust vent to the coupling and secure with a 4" (10.2 cm)
vent clamp. See Illustration below.
If connecting to existing vent, make sure the vent is clean.
4. Turn the coupling and exhaust vent assembly
counterclockwise in the exhaust hole on the back of the
dryer.
5. Make sure the exhaust vent is placed inside the exhaust hood
and then secured to the exhaust hood with a 4" (10.2 cm)
vent clamp.
6. Move dryer into its final location. Do not crush or kink vent.
Level Dryer
Check the levelness of the dryer. Check levelness first
side to side, then front to back.
If the dryer is not level, prop up the dryer using a wood block.
Use a wrench to adjust the legs up or down and check again for
levelness.
Number of
90ºturns
or elbows
Type of vent Box or
louvered
hoods
Angled
hoods
0 Rigid metal
Flexible metal 90 ft (27.4 m) 64 ft (19.5 m) 80 ft (24.4 m) 58 ft (17.7 m)
1 Rigid metal
Flexible metal 80 ft (24.4 m) 58 ft (17.7 m) 70 ft (21.3 m) 52 ft (15.8 m)
2 Rigid metal
Flexible metal 70 ft (21.3 m) 50 ft (15.2 m) 60 ft (18.3 m) 42 ft (12.8 m)
WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
A. Coupling
B. Vent clamp
C. Vent coupler
D. Vent clamp
E. Rigid or flexible metal vent
ABCDE

10
Complete Installation
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check the dryer’s final location. Be sure the vent is not
crushed or kinked.
5. Check that the dryer is level. See “Level Dryer.”
6. Plug into a grounded 4 prong outlet.
7. Remove the clear protective film on the front edge and any
tape remaining on the dryer.
8. Read “Dryer Use.”
9. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
10. Set the dryer on a full heat cycle (not an air cycle) for
20 minutes and start the dryer.
If the dryer will not start, check the following:
■Controls are set in a running or “On”position.
■Start button has been pushed firmly.
■Dryer is plugged into a grounded outlet.
■Electrical supply is connected.
■Household fuse is intact and tight, or circuit breaker has
not tripped.
■Dryer door is closed.
11. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat. If you feel heat, cancel cycle and
close the door.
If you do not feel heat, turn off the dryer and check the
following:
■There may be 2 household fuses or circuit breakers for the
dryer. Check to make sure both fuses are intact and tight, or
that both circuit breakers have not tripped. If there is still no
heat, contact a qualified technician.
NOTE: You may notice a burning odor when the dryer is first
heated. This odor is common when the heating element is first
used. The odor will go away.
WARNING
Electrical Shock Hazard
Plug into a grounded 4 prong outlet.
Failure to do so can result in death or electrical shock.

11
DRYER USE
Starting Your Dryer
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
Before using your dryer, wipe the dryer drum with a damp cloth to
remove dust from storing and shipping.
IMPORTANT: For best performance, do not use fabric softener
sheets in this dryer. You may use liquid fabric softener in the
washer.
1. Clean the lint screen before each load. See “Cleaning the Lint
Screen.”
2. Load clothes loosely into the dryer and close the door. Do not
pack the dryer. Allow space for clothes to tumble freely.
3. Press the POWER button to turn the dryer on. The indicator
light will glow to indicate that the power is on.
4. Press the TEMPERATURE button to select the recommended
temperature setting for the type of load being dried. See
“Temperature Control.”
5. Turn the cycle knob to the recommended setting for the type
of load being dried. See “Drying, Cycle and Temperature
Tips.”
6. After a short beep sounds, press the START button.
Stopping and Restarting
To stop your dryer at any time
Turn the cycle knob to the STOP position or open the door.
To restart the dryer
1. Close the door.
2. Select a new cycle and temperature (if desired).
3. After the beep sounds, press the START button.
Changing Cycles and Temperatures
To change the cycle or temperature after pressing START
1. Open the dryer door.
2. Press the TEMPERATURE button to change the temperature
(if desired).
3. Turn the cycle knob to the new desired position.
4. After the beep sounds, press the START button.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in death,
explosion, or fire.
WARNING
Fire Hazard
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Do not dry items containing foam, rubber, or plastic in
this dryer.
Doing so can result in death or fire.

12
Controls
The control panel is simple to understand and easy to operate.
The illustrations below define the knobs and buttons, and the
paragraphs define the purpose of each.
Power
This button switches the power to the machine on and off. The
indicator light will glow to indicate the power is on.
Indicator Light
This light indicates when the power is on or if a cycle has started.
Temperature
The Temperature Control button lets you select between a normal
and low drying temperature.
NOTE: Always refer to the care label on the garment to determine
whether it can be tumble dried.
Normal
The Normal temperature setting is for sturdy fabrics, such as
cotton, linen and denim. If the Temperature Control button is not
pressed in, the temperature setting is Normal.
Low
The Low setting is for synthetics, such as cotton/polyester blend,
rayon, acetate, washable silk or nylon. If the Temperature Control
button is pressed in, the temperature setting is Low.
Cycle Knob
Turn this knob to the recommended setting. Indicator light will
flash to indicate a cycle has been selected. See “Drying, Cycle
and Temperature Tips.”
Stop Position
Turn the cycle knob to the Stop position at any time.
Start Button
After you have selected a cycle and temperature, press this
button to start the cycle. Indicator light will glow to indicate the
cycle has started.
Drying, Cycle and Temperature Tips
Select the correct cycle and temperature for your load.
Your dryer tumbles the load without heat during the last few
minutes of all cycles to make the load easier to handle and to
reduce wrinkling. After the cool-down cycle ends, the light
flashes, and an end-of-cycle signal sounds to indicate the cycle
is complete.
Drying tips
■Follow care label directions when they are available.
■Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits and synthetic fabrics.
■Avoid drying heavy work clothes with lighter fabrics. This
could cause overdrying of lighter fabrics, leading to increased
shrinkage or wrinkling.
Cycle and temperature tips
■Dry most loads using an automatic cycle.
■Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions.

13
Cycles
Automatic Cycles
When you are using the Auto Moisture Sensing Cycle, two metal
strips (sensors) located on the dryer baffles determine the
dryness of the load. The metal strips help detect the amount of
moisture left in the clothes as they pass. When there is moisture
left in the clothes, the machine will continue to run. As clothes
begin to dry, the amount of water left in the clothes decreases,
and the timer advances through the remainder of the cycle. When
the selected dryness level is reached, the dryer goes into a cool
down period of up to 15 minutes.
Automatic cycles may be used for most loads. Automatic cycles
give the best drying results in the shortest time. Drying time
varies according to the type of fabric, size of the load and
dryness setting.
After drying a load, check the dryness.
■If the load is drier than you like, select a setting closer to Less
Dry the next time you dry a similar load.
■If a load is not as dry as you like, complete drying using a
Timed cycle. Select a setting closer to More Dry the next time
you dry a similar load.
See following table for recommended cycles and temperature
settings.
Timed Dry
Use this cycle to get up to 60 minutes of heated drying time or to
complete drying if items are still damp after the automatic cycle.
Timed Dry is also useful for:
■Heavyweight items and work clothes that require a long
drying time.
■Lightweight items, such as lingerie, blouses and knits that
require a short drying time.
See following table for recommended cycles and temperature
settings.
End of Cycle Signal
The dryer sounds a signal to let you know when the cycle is
complete. The signal is not adjustable and cannot be turned off.
The signal is helpful when you are drying permanent press,
synthetics, and other items that should be removed promptly at
the end of the cycle.
Anti-Wrinkle
Anti-Wrinkle helps avoid wrinkles that form when clothes are not
removed promptly at the end of a cycle. Anti-Wrinkle tumbles the
load every minute until the cycle knob is set to the Stop position
or the dryer door is opened.
During Anti-Wrinkle, the End of Cycle Signal will sound until the
cycle knob is set to the Stop position or the dryer door is opened.
Fabric Type Cycle Temperature
Setting
REGULAR
Heavy cottons and denims More Dry Normal
Cottons and linens Normal Normal
SYNTHETICS
White and colorfast
permanent press Normal Low
White and colorfast items
that require ironing Less Dry Low
Polyester/acrylic blends,
rayon, acetate Delicates Low
Washable silk and nylon Delicates Low
Fabric Type Time
(minutes) Temperature Setting
Heavy cottons and denims 60 Normal
Cottons and linens 40 Normal
White and colorfast
permanent press 40 Low
White and colorfast items
that require ironing 40 Low
Polyester/acrylic blends,
rayon, acetate 40 Low
Washable silk and nylon 40 Low

14
DRYER CARE
Cleaning the Dryer Location
Keep dryer area clear and free from items that would obstruct the
flow of combustion and ventilation air.
Cleaning the Lint Screen
Every load cleaning
The lint screen is located in the door opening of the dryer. Clean
the lint screen before each load. A screen blocked by lint can
increase drying time.
To clean
1. Open the door and pull the lint screen straight up.
2. Open lint screen.
3. Roll lint off the screen with your fingers. Do not rinse or wash
screen to remove lint. Wet lint is hard to remove.
4. Close lint screen. Push the lint screen firmly back into place
and close the door.
IMPORTANT:
■Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
As needed cleaning
Laundry detergent and fabric softener residue can build up on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off the screen.
Clean the lint screen with a nylon brush every 6 months, or more
frequently if it becomes clogged due to a residue buildup.
To wash
1. Roll lint off the screen with your fingers.
2. Wet both sides of the lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
4. Rinse with hot water.
5. Thoroughly dry lint screen with a clean towel. Replace in
dryer.
Cleaning the Dryer Interior
To clean dryer drum
1. Make a paste with powdered laundry detergent and very
warm water.
2. Apply paste to a soft cloth.
OR
Apply a liquid, nonflammable household cleaner to the
stained area and rub with a soft cloth until all excess dye is
removed.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.

15
3. Wipe drum thoroughly with a damp cloth.
4. Tumble a load of clean cloths or towels to dry drum.
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and will
not stain future loads of clothes. Dry unstable dye items inside-
out to avoid dye transfer.
Cleaning the Control Panel
To clean the control panel, use only a warm, damp cloth.
NOTE: Do not use abrasive cleaners or scouring pads on the
outer surfaces because they will scratch the finish and could
remove the writing on the control panel.
Some paper towels may also scratch the finish.
Removing Accumulated Lint
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
From the Exhaust Vent
Lint should be removed every 2 years, or more often, depending
on dryer usage.
Vacation and Moving Care
Vacation care
Operate your dryer only when you are at home. If you will be on
vacation or not using your dryer for an extended period of time,
you should:
1. Unplug dryer or disconnect power.
2. Clean lint screen. See “Cleaning the Lint Screen.”
Moving care
1. Unplug the power supply cord.
2. Make sure leveling legs are secure in dryer base.
3. Use masking tape to secure dryer door.
TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
Dryer Operation
Dryer will not run
■Has a household fuse blown, or has a circuit breaker
tripped?
There may be 2 fuses or circuit breakers for the dryer. Check
to make sure both fuses are intact and tight, or that both
circuit breakers have not tripped. Replace the fuse or reset
the circuit breaker. If the problem continues, call an
electrician.
■Is the correct power supply available?
Electric dryers require 240 volt power supply. Check with a
qualified electrician.
■Was a regular fuse used?
Use a time-delay fuse.
■Is the dryer door firmly closed?
■Was the Start button firmly pressed?
■Is the motor running but the drum isn’t turning?
The belt may be broken. Call for service.
■Is the indicator light glowing? Press the POWER button. If
the indicator light does not glow, call for service.
No heat
■Has a household fuse blown, or has a circuit breaker
tripped?
Electric dryers use 2 household fuses or circuit breakers. The
drum may be turning, but you may not have heat. Replace the
fuse or reset the circuit breaker. If the problem continues, call
an electrician.
Unusual sounds
■Has the dryer had a period of non-use?
If the dryer hasn’t been used for a while, there may be a
thumping sound during the first few minutes of operation.
■Is a coin, button, or paper clip caught between the drum
and front or rear of the dryer?
Check the front and rear edges of the drum for small objects.
Clean out pockets before laundering.
■Are the four legs installed, and is the dryer level front to
back and side to side?
The dryer may vibrate if not properly installed. See the
“Installation Instructions.”
■Is the clothing knotted or balled up?
When balled up, the load will bounce, causing the dryer to
vibrate. Separate the load items and restart the dryer.

16
Dryer Results
Clothes are not drying satisfactorily, drying times are too
long, or load is too hot
NOTE: The compact dryer operates at a lower wattage. Expect
longer drying times.
■Is the lint screen clogged with lint?
Lint screen should be cleaned before each load.
■Is the exhaust vent or outside exhaust hood clogged with
lint, restricting air movement?
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not
feel air movement, clean exhaust system of lint or replace
exhaust vent with heavy metal or flexible metal vent. See the
“Installation Instructions.”
■Is the exhaust vent the correct length?
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the
“Installation Instructions.”
■Is the exhaust vent diameter the correct size?
Use 4" (10.2 cm) diameter vent material.
■Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
■Is the dryer located in a closet?
Closet doors must have ventilation openings at the top and
bottom of the door. The rear of the dryer requires a minimum
of 5½" (14 cm) of airspace, and 1" (2.5 cm) is recommended
for the sides and front of the dryer. See the “Installation
Instructions.”
■Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
Cycle time too short
■Is the automatic cycle ending early?
The load may not be contacting the sensor strips. Level the
dryer.
Change the dryness level setting on Automatic Cycles.
Increasing or decreasing the dryness level will change the
amount of drying time in a cycle.
Lint on load
■Is the lint screen clogged?
Lint screen should be cleaned before each load.
Stains on load or drum
■Drum stains are caused by dyes in clothing (usually blue
jeans). This will not transfer to other clothing.
Loads are wrinkled
■Was the load removed from dryer at the end of the cycle?
■Was the dryer overloaded?
Dry smaller loads that can tumble freely.
Odors
■Have you recently been painting, staining or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
■Is the dryer being used for the first time?
The new electric heating element may have an odor. The odor
will be gone after the first cycle.
WARNING
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.

17
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.”It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use factory specified parts. These parts will fit right and work
right because they are made with the same precision used to
build every new INGLIS®appliance.
To locate factory specified parts in your area, call
1-800-807-6777, or your nearest designated service center.
Our consultants provide assistance with:
■Features and specifications on our full line of appliances.
■Use and maintenance procedures.
■Accessory and repair parts sales.
■Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool Canada LP designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service anywhere in Canada.
For further assistance
If you need further assistance, you can write to Whirlpool Canada
LP with any questions or concerns at:
Customer Interaction Centre
Whirlpool Canada LP
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.

18
INGLIS
®
DRYER WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished
with the product, Whirlpool Canada LP will pay for factory specified parts and repair labor costs to correct defects in materials or
workmanship. Service must be provided by a Whirlpool Canada LP designated service company.
Whirlpool Canada LP will not pay for:
1. Service calls to correct the installation of your dryer, including venting. Heavy 4" (10.2 cm) metal exhaust vent must be used. Refer
to the venting section of this manual and the Installation Instructions.
2. Service calls to instruct you how to use your dryer, to replace household fuses or correct house wiring or reset circuit breakers, or to
replace owner accessible light bulbs.
3. Repairs when your dryer is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not
approved by Whirlpool Canada LP.
5. Replacement parts or repair labor costs for units operated outside Canada.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Travel or transportation expenses for customers who reside in remote areas.
WHIRLPOOL CANADA LP SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from province to province.
Outside Canada, this warranty does not apply. Contact your authorized Whirlpool Canada LP dealer to determine if another
warranty applies.
If you need service, first see “Troubleshooting.”Additional help can be found by checking “Assistance or Service,”or by calling
Whirlpool Canada LP at 1-800-807-6777.4/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your dryer to better
help you obtain assistance or service if you ever need it. You will
need to know your complete model number and serial number.
You can find this information on the model and serial number
label, located on your appliance as shown in “Parts and Features.”
Dealer name____________________________________________________
Address ________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________

19
SÉCURITÉDE LA SÉCHEUSE
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécuritévous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécuritéimportants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécuritéet de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécuritévous signale les dangers potentiels de décès et de blessures graves àvous
et àd’autres.
Tous les messages de sécuritésuivront le symbole d’alerte de sécuritéet le mot “DANGER”ou
“AVERTISSEMENT”. Ces mots signifient :
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
Pour réduire le risque d'incendie, de choc électrique ou de blessure lors de l'utilisation de
la sécheuse, il convient d'observer certaines précautions élémentaires dont les suivantes :
AVERTISSEMENT :
■Lire toutes les instructions avant d'utiliser la sécheuse.
■Ne pas placer des articles exposés aux huiles de cuisson
dans votre sécheuse. Les articles contaminés par des
huiles de cuisson peuvent contribuer àune réaction
chimique qui pourrait causer àla charge de s'enflammer.
■Ne pas faire sécher dans la machine des articles qui ont
déjàéténettoyés, lavés, imbibés, ou tachés d'essence,
de solvants pour nettoyage àsec, d'autres substances
inflammables, ou de substances explosives puisqu'elles
dégagent des vapeurs qui peuvent provoquer un
incendie ou une explosion.
■Ne pas permettre àdes enfants de jouer sur ou à
l'intérieur de la sécheuse. Une surveillance étroite est
nécessaire lorsque la sécheuse est utilisée près d'eux.
■Avant d'enlever la sécheuse du service ou la jeter, enlever
la porte du compartiment de séchage.
■
Ne pas mettre la main dans la sécheuse si le tambour est
en mouvement.
■Ne pas réparer ni remplacer une pièce de la sécheuse ou
essayer d'en faire l'entretien àmoins d'une recommandation
spécifique dans le guide d'utlilisation et d'entretien, ou
publiée dans les instructions de réparation par l'utilisateur
que vous comprenez et pouvez exécuter avec compétence.
CONSERVEZ CES INSTRUCTIONS
■
Ne pas installer ni entreposer la sécheuse oùelle sera
exposée aux intempéries.
■Ne pas jouer avec les commandes.
■Ne pas utiliser un produit assouplissant de tissu ou des
produits pour éliminer la statique àmoins qu'ils ne soient
recommandés par le fabricant du produit assouplissant de
tissu ou du produit.
■Ne pas utiliser la chaleur pour faire sécher des articles
fabriqués avec du caoutchouc mousse ou des matériaux
semblables.
■Nettoyer le filtre àcharpie avant et après chaque charge.
■Ne pas laisser la charpie, la poussière, ou la saleté
s'accumuler autour du système d'évacuation ou autour de
l'appareil.
■Un nettoyage périodique de l'intérieur de la sécheuse et du
conduit d'évacuation doit être effectuépar une personne
qualifiée.
■Voir les instructions d'installation pour les exigences de
liaison de l'appareil àla terre.

20
EXIGENCES D’INSTALLATION
Outillage et pièces
Outillage requis
Rassembler les outils et pièces nécessaires avant de commencer
l’installation. Lire et suivre les instructions fournies avec les outils
indiqués ici.
Pièces fournies
Retirer le sachet de pièces du tambour de la sécheuse. Vérifier
que toutes les pièces de la liste sont présentes.
Pièces nécessaires
Consulter les codes locaux, vérifier l'alimentation électrique et le
circuit d'évacuation existants, et consulter les sections
“Spécifications électriques”et “Exigences concernant
l'évacuation”avant d'acheter des pièces.
Les installations en maison mobile nécessitent du matériel pour
système d’évacuation en métal. Pour des informations sur la
commande, veuillez vous référer àla section “Assistance ou
service”de ce manuel. Vous pouvez également contacter le
marchand chez qui vous avez achetévotre sécheuse.
Options
Piédestal
Vous pouvez commander un piédestal séparément pour cette
sécheuse. Ce piédestal ajoutera environ 12" (30,48 cm) àla
hauteur de l'appareil pour une hauteur totale d'environ
45" (114,3 cm).
Pour commander, téléphoner au marchand chez qui la sécheuse
a étéachetée ou se référer àla section “Assistance ou service”
de ce manuel. Demander le modèle n°LAB0050PQ.
Ensemble de superposition
Prévoyez-vous de superposer votre laveuse et votre sécheuse?
Pour ce faire, vous devrez acheter un ensemble de superposition.
Pour commander, téléphoner au marchand chez qui la laveuse a
étéachetée ou se référer àla section “Assistance ou service”de
ce manuel. Demander la pièce n°8182452.
Emplacement d’installation
Il vous faudra
■Un emplacement qui permet l’installation d’un système
d’évacuation approprié. Voir “Exigences concernant
l’évacuation”.
■Un circuit distinct de 30 ampères.
■Une prise électrique avec liaison àla terre située àmoins de
2pi(61cm)del’un des côtés de la sécheuse. Voir
“Spécifications électriques”.
■Un plancher robuste capable de soutenir le poids total de la
sécheuse (sécheuse et chargement) de 115 lb (52 kg). Il faut
aussi prendre en compte le poids combinéd'un appareil
ménager voisin.
■Un plancher de niveau ayant une pente maximale de
1" (2,5 cm) sous l’ensemble de la sécheuse.
Ne pas faire fonctionner la sécheuse àdes températures
inférieures à45ºF (7ºC). Àdes températures inférieures, la
sécheuse risque de ne plus s’arrêter àla fin d’un programme
automatique. Ceci risque de prolonger les durées de séchage.
La sécheuse ne doit pas être installée ou remisée dans un endroit
oùelle sera exposée àl'eau et/ou aux intempéries.
Vérifier les règlements locaux. Certains codes limitent ou
n’autorisent pas l’installation des sécheuses dans un garage, un
placard, une maison mobile ou une chambre àcoucher.
Communiquer avec l’inspecteur des bâtiments local.
■Tournevis àlame plate
■Cléàmolette
■Tournevis T20 TORX®†
■Pistolet àcalfeutrage et
composéde calfeutrage
(pour l'installation d'un
nouveau conduit
d'évacuation)
■Cisaille de ferblantier
(nouvelles installations
d'évacuation)
■Bloc de bois
■Niveau
■Clapets d’évacuation
Raccord
Piédestal facultatif
†®TORX est une marque déposée de Textron Innovations Inc.
Risque d'explosion
Garder les matières et les vapeurs inflammables, telle
que l’essence, loin de la sécheuse.
Placer la sécheuse au moins 46 cm (18 po) au-dessus
du plancher pour une installation dans un garage.
Le non-respect de ces instructions peut causer
un décès, une explosion ou un incendie.
AVERTISSEMENT