InLife JW-6638 User manual

User Manual
Any problem or question about the product, please email via [e-mail] for help
I. Function
1. Led time display in 12H-24H format
2. White light and color light
3. Sunrise simulation wake up light
4. Sunset light
5. Touch mode
6. Wake up to natural sounds or FM radio
7. FM Radio and antenna built in
8. Power supply: DC 5V, 1 x CR2032 battery or USB cable
II. Diagram
III. Operation
1. Place the Wake-up Light 16-20in/40-50cm away from your head, for example on a bedside table.
2. Power
Connect with DC 5V power and insert 1xCR2032 battery. Note that the battery is for time backup only.
3. Setting the clock time
3.1 When you plug in the appliance for the first time or there has been a power failure, the hour indication starts to blink, you
can adjust hour/minute by press , and press to confirm hour/minute.
3.2 To adjust the time display, press button for 3 sec until the hour display starts to flash. Press to set the
hour/minute, and press to confirm hour/minute. The display will exit the setting mode if no buttons are pressed for
10 seconds.

3.3 When the time is set, press to switch between the 12H and 24H modes. In the 12H mode, AM or PM will
be displayed.
3.4 Press button to adjust the brightness of time display : Low - High - Off.
4. Light
4.1 Press button at first to turn on the light and press buttons to adjust the brightness from 1 to 10.
4.2 Pressing button for a second time to enter the color mode. Press to select color : Green, Red, Blue, Purple,
Orange and Indigo.
4.3 Pressing button for the third time, the light is off.
5. Setting the alarm wake-up time and sound
5.1 Press button to turn on/off the alarm. The alarm symbol will be appeared on the display when you turn on the alarm.
It will be disappeared when you turn off the alarm.
5.2 Press for 3 seconds to set the alarm, the hour indication starts to blink and you can adjust the alarm time by press
, and press to confirm hour/minute.
5.3 Wake-up sound
Press button to set the wake-up sound. Press to select the sound you want. Each sound(1-6) will play for 60
sec when selected. Sound 7 is the FM radio. Press button to confirm your choice.
If choosing 7 as alarm sound, there is no sound will be played and your last listened FM radio frequency will be as
wake-up sound(please sure you have listened the Radio), and then press to confirm the sound.
Press / to choose wake-up sound volume level, and there are 15 level can be chosen.
6. Sunrise light simulation
30 minutes before the alarm time, the light will come on and gradually increase in brightness. At the alarm time, the wake-up
sound or radio sound will play for 5 minutes.
While the sound is playing, you can:
Press or touch any button to stop the sound and light, except button.
Press button to stop the sound and light. 5 minutes later, the sound will start playing again and the light will come
on again.
Press button for 3 sec to turn off the light.
If the FM radio is playing at the alarm time, it will turn off and the wake-up sound will play. When the wake-up sound stops,
the radio will resume playing.

7. Sunset light simulation
7.1 Touch button to set the sunset light simulation. Pressing the button repeatedly, 15/30/60/OFF will display, and select the
sunset time your like. For example, if you choose 15(30, 60), the light will automatically turn off after 15(30, 60) minutes.
When the desired number is displayed, don’t press any button for 5 sec, and then the sunset time was set and normal
operation will resume.
7.2 During sunset simulation, the button will flash. Press button to cancel the sunset simulation and keep the current
brightness. Press the button for 3 sec to switch off the sunset light.
7.3 If FM radio is playing during sunset, the radio will be turn off together with the sunset light.
8. FM radio
8.1 Press the button to turn on/off the radio. Press the button for 3 sec to scan FM station automatically and available
FM station will be saved automatically. Press the button to select a FM station. Press the / button to set the radio
volume(00-15).
Ⅳ. Safety Guidelines
In the event that the unit malfunctions, unplug it for 3 seconds, then plug in again.
The battery is only used for setting backup.
Don’t immerse the light in water or any other liquid.
Don’t throw the light in a fire.
Don’t press more than one key at the same time.
For the button function to work properly, buttons should be pressed for at least 1 second.
Remove batteries if the unit is not used for extended periods.