Innova FIESTA 1001 User manual

REV. 03/05/2020 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
Sand
15 lbs
(not included)
Sand
Contents of Accessory box 1001-HRK
x2
x2
x4
SCREW BAG 140-0008
Opera #1016 Shell
x2
Fiesta #1001 Shell
x4
A
x8
1) Insert the four posts into the
step and secure them in place with
the bolts, washers, and nuts
provided.
2) Insert the deck supports over
the two rear posts. Do not secure.
3) Insert the handrails onto the
posts and secure them with the
screws provided.
x1
x8 x8 x8
(1 IN.)
(1 ¹⁄2 IN.)
(³⁄4 IN.)
x16 x12
AB C D E
Required tools (not included)
Phillips #2
Phillips #3
7/16 wrench
Phillips bit
FIESTA 1001
OPERA 1016
x8 x8 x8
A B C
D
Useful tip!
To ease the installation of
handrails and bolts, use a
Phillips screwdriver to line
up the holes.
FIESTA / OPERA WITH DECK
WARNING
Install the step on a flat surface.
Do not jump or dive from the step.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.

2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
REV. 03/05/2020 PN: PG:2
1 year on pool step.
1 year on hardware.
MANUFACTURER WARRANTY
B
1) Insert the four Step Cups into
the holes under the step.*
x4
B3) Twist the Step Cup to ensure that
the mushroom ring has entirely cleared
the wall thickness. If it has, the suction
cup should rotate freely.
Failing to install the Step Cup
TM
system will greatly reduce the steadiness of the step and will void the manufacturer warranty.
B2) With a flat screwdriver, compress the
Step Cup mushroom ring while pushing it
into the hole.
CAUTION
B1) Insert half of the Step Cup mushroom
ring in the hole, at a 45 degree angle.
C
D
x4
x12
1) Affix the two deck supports to
the deck with the screws
supplied.
2) Install the post covers on the
handrails.
* View step cups installation tips on YouTube:
https://www.youtube.com/watch?v=W5RH1VNxpu0
FIESTA / OPERA WITH DECK
Minimum 1”
CAUTION
Sand
15 LB
Align holes
1) Fill the ballast with
sand. The approximate
weight should
be 15 lbs.
2) Screw the lid in place and
align the cover ribs with the
holes in the ballast base. 3) Fasten the cover to the
ballast base with the four
screws provided.
4) Slowly submerge the step
into the pool. Make sure you do
not damage the pool liner
in the process.
5) Angle the whole step so that
it is entirely under water. Purge
all the air from under the steps.
6) Slide the two deck supports
to the height of the deck.
7) Drop the ballast in the step
hole.
To prevent pool liner puncture, keep a minimum 1" gap
between the pool liner and the rear underside of the step.
x4
D
3) Pull the deck supports
(already fixed to the deck)
upwards to create a spring
effect on the step.
4) Fasten the supports to the
two rear posts while
pushing the entire step
downwards.
D
D
E