Innovative Technology ITUT-300 User manual

USER MANUAL
ITUT-300
USB TURNTABLE

1
Table of Contents
Important Safety Instructions---------- Page 2
Precautions---------------------------------Page 4
Before Use----------------------------------Page 5
Location of Parts--------------------------Page 6
Preparation for Use----------------------Page 6
How to Replace the Stylus-------------Page 7
Listening to a Record-------------------Page 8
Audacity Software Introduction-------Page 9
Audacity Installation--------------------Page 12
Configuring Audacity for Windows--Page 16
Audacity Control Buttons--------------Page 17
Audacity Preferences------------------Page 18
Preparing to Export and Save Files-Page 20
Export and Save Files------------------Page 23
Recording Operation Steps-----------Page 25
Dividing Tracks--------------------------Page 26
Configuring Audacity for Mac--------Page 30
Audacity Control Buttons--------------Page 31
Audacity Preferences------------------Page 32
Select the recording device-----------Page 33
To set the Smart Recording-----------Page 34
Export and Save Files------------------Page 35
Troubleshooting-------------------------Page 37
Specifications----------------------------Page 37

2
PART I: USB TURNTABLE
IMPORTANT SAFETY INSTRUCTIONS FOR AUDIO PRODUCTS-READ
THOROUGHLY
When using electrical products, basic precautions should always be followed including:
1. Read Instructions-All the safety and operating instructions should be read before the product
is operated.
2. Retain Instructions-The safety and operating instructions should be retained for future
reference.
3. Heed Instructions-All warnings on the product and in the operating instructions should be
adhered to.
4. Follow Instructions-All operating and user instructions should be followed.
5. Cleaning-Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments-Do not use attachments not recommended by the product manufacturer as they
may cause hazards.
7. Water and Moisture-Do not use this product near water-for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
8. Accessories-Do not place this product on an unstable surface. The product may fall, causing
serious injury to a child or adult and serious damage to the product. Use only with a stand,
bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of
the product should follow the manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer.
9. Transporting-This product should be moved with care to avoid
damage or injury.
10. Ventilation-Slots and openings in the cabinet are provided for
ventilation, to ensure reliable operation of the product and to protect it
from overheating. These openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed,
sofa, rug, or similar surface. This product should not be placed in a
built-in installation such as a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11. Power Sources-This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your home, consult your
product dealer or local power company. For products intended to operate from battery power, or
other sources, refer to the operation instructions.
12. Power-Cord Protection- Power-supply cords should be routed so that they are not likely to be
trapped in any way.

3
13. Lightning-For added protection for this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product due to lightning and
power-line surges.
14. Power Lines-An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
15. Overloading-Do not overloads wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
16. Object and Liquid Entry-Never push objects of any kind into this product through openings as
they may touch dangerous voltage points or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
17. Servicing-Do not attempt to service this product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
18. Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions, as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way, and the product exhibits a distinct
change in performance-this indicates a need for service.
19. Replacement Parts-When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check-Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating
condition.
21. Wall or Ceiling Mounting-The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. Heat-The product should be situated away from heat sources such as radiators, heat registers,
stoves or other products (including amplifiers) that produce heat.

4
Precautions
Safety Information
CAUTION:
1. In order to shut off the power of this product completely, unplug the power cord from the wall outlet.
Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as a
vacation.
2. Use of controls, adjustments and performance of procedures other than those specified herein
may result in hazardous radiation exposure.
3. If this product develops trouble, contact a qualified service center, and do not use the product in
defective state.
Safety Precautions
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION
RISKS OF ELECTRIC SHOCK- DO NOT OPEN!
To reduce the risk of electric shock, do not remove cover or back.
No user serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert user to the presence of non-insulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
(See markings on the back of the unit)
CAUTION:
To prevent electric shock, match wide blade of plug to wide slot, fully insert.

5
Instructions shall caution users that modifications not approved by the party responsible
for compliance could void user’s authority to operate the equipment.
The following or equivalent as appropriate:
“NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.”
Statement that the product complies with Part 15 (i.e. “This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.”
CALIFORNIA PROP 65 WARNING
"WARNING" This product contains a chemicals known to the State of California to cause
birth defects or other reproductive harm. For more information on these regulations and a
list of chemicals, log on the following website address :
http://www.oehha.ca.gov/prop65.html
Before Use
1. Choose unit installation location carefully. Avoid placing it in direct sunlight or close to a source of
heat. Also avoid locations subject to vibrations and excessive dust, cold or moisture. Keep away from
sources that hum, such as transformers or motors.
2. Do not open the cabinet as this might result in damage to the circuitry or electrical shock.If a
foreign object should get into the set, contact your dealer.
3. Be sure not to handle stylus (needle) with dirty fingers.
4. When removing the power plug from the wall outlet, always pull directly on the plug, never pull the
cord.
5. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Use a
clean, dry cloth.
6. In order to shut off the power to this product completely, unplug the power cord from the wall outlet.
Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as a
vacation.
7. Keep this manual in a safe place for future reference.

6
Location of parts
1. RCA Line
2. USB Socket
3. AC Line
4. PLAY/PAUSE Button
5. POWER Button
6. Balance Weight
7. Tone Arm
8. Security Tie
9. Tone Arm Holder
10. Stylus
11. Eject Button
12. Speed Control Button
13. Turntable
14. Rubber Mat
Preparation for Use
1. Connect the AC power cord to AC outlet.
2. Remove white protective needle cover by gently pulling towards front of unit.

7
3. Screwed the balance weight on the tone arm through the center, please refer to below instruction.
If the sound is distortion, please turning the balance weight clockwise or counterclockwise.
4. Put the rubber mat on the turntable.
5. Release TONE ARM REST by gently pushing hold-down clip to the right. This will unlock tone arm
from its arm rest. Re-lock the hold-down clip when moving the unit to another location.
How to Replace the Turntable Stylus (Needle)
Removing old stylus
1. Set a screwdriver at the tip of the stylus and push
down in the direction “A”.
2. Remove the stylus by pulling it forward and down.
Installing a new stylus
1. Hold the tip of the stylus and insert the other edge
by pressing in the direction “B”.
2. Push up in the direction “C” until it locks at the tip.

8
**Note: For information regarding stores that carry replacement needles for your ITUT-300 unit, please
contact us by sending an email to: [email protected] or call toll-free 1-877-483-2497.
Listening to a Record
1. Connect the AC power cord to AC outlet.
2. Plug the 2 ends of the LINE OUT Cable into the auxiliary input (Aux) on your TV, home
entertainment receiver or other music systems. Be sure that the red RCA Cable is inserted into the
red jack and the white RCA Cable is inserted into the white jack.
3. Press the POWER button on the unit. Also turn the power on the unit that you connected with this
turntable.
4. Put a record onto the turntable.When playing a 45rpm record, remember to use the adapter
packed in the polybag along with the manual.
5. Select player speed (33-1/3, 45 OR 78 rpm) according to the record you are playing.
6. Remove the tone arm-rest holder, lift the que-lever and move the tone arm gently to the desired
position over the record. Lower the que-lever slowly and record will start to play.
7. Adjust the volume on your auxiliary source to control the volume of the music.
8. Press the PLAY button to continue playing.
9. When the music playing is finished and tone-arm reaches the end of the record, the tone-arm will
return back to the arm-rest automatically. Or you can press the eject button when playing the record
and the tone arm will lift up from the record and automatically return to the arm-rest.
10. Remember to unplug the plug when not playing the unit for extended periods of time.

9
PART II: Audacity Software
The provided CD disc contains the following software:
(1)audacity-src-1.2.6--------- For source codes
(2)Audacity_for_MAC---------For Macintosh
(3)Audacity_for_WIN---------For Windows
(4)AUTORUN.INF
(5)The GNU General Public License.html
The software is compatible with Window 98, 2000, ME, XP, VISTA and Macintosh.
Audacity Installation and USB Connection
Connect the USB cable to the turntable and into your computer. Connect the AC cord of turntable.
Press Power button to turn on the turntable.
1. Please insert the Audacity software disk that comes with your unit. Go to My Computer and double
click the CD ROM Drive.

10
2. There are five folder in the Audacity disk. Select Audacity_for_WIN for Windows system, and
select Audacity_for_MAC for Macintosh system.
3. Double click the Audacity_for_WIN for Windows system, and double click the audacity-win-1.2.6
to install the audacity software.

11
4. Double click the Audacity_for_MAC for Macintosh system. There are three folders will appear as
below. If your computer is Mac OS X system (Intel CPU), please enter the Intel folder to install the
audacity software; If your computer is Mac OS 9 system, please enter the Mac OS 9 folder to install
the audacity software; If your computer is Mac OS X system (Power PC CPU), please enter the PPC
folder to install the audacity software.

12
Installing the Audacity Software
1. TheAudacity Setup Wizard will appear. Click on Next to install the software.
2. Click on “I accept the agreement” and click on Next.

13
3. Continue to click on the Next buttons.

14
4. Click on the Install button to start installation.

15
5. Click on Finish to complete installation.
6. You can now open the Audacity software and start recording your files.
(For additional information, visit the Audacity website at http://audacity.sourceforge.net)

16
Configuring Audacity for Microsoft Windows
Audacity Interface
Audacity Interface---Settings and controls.

17
Audacity Control Buttons
Using the attribute controls button at the top of the screen to go to beginning, Play, Record, Pause,
Stop and End. Use the File, Edit, View, Project, Generate, Effect and Analyze menus to Save, Export,
and edit the music.
1. Click the ( ) button to skip to start;
2. Adjust the output volume.
3. Click the ( ) button to play;
4. Click the ( ) button to record;
5. Click the ( ) button to pause the recording;
6. Click the ( ) button to stop the recording;
7. Adjust the input volume.
8. Click the ( ) button to skip to end;

18
Audacity Preferences
Click the “Edit” on the Audacity interface, select “Preferences”.
zThe screen will open up Audacity Preferences. You can see the AudioI/O, Quality, File
Formats, Spectrograms, Directories, Interface, Keyboard and Mouse in the Audacity
preference interface.

19
Select the recording device: microphone (USB Audio CODEC)
zClick the “Audio I/O” at the Audacity Preferences interface.
zClick the “Device” and select “microphone (USB Audio CODEC)”.
zClick the “Channels” and select 2 (stereo).
zClick the “OK”.
zNote: If you couldn't find the " microphone (USB Audio CODEC) " from the Device list, close
the Audacity Software and re-open then try again.
4. Adjust the output and input volume.
NOTE: Because of the variation of different operation system, the input volume control may not work
on some individual Windows versions. Windows Vista is recommended to ensure the input volume
control working properly.