Innovative THE PROTECTOR User manual
PLEASE READ ALL OF THE INSTRUCTIONS BEFORE
USING THE MOISTURE METER.
This instrument can be used to measure the amount of water in
the wood, building material, and measure the environment
temperature.
FEATURES:
·Display: LCD display with green color backlight.
·Measurement range: Wood: 6 to 60%
Building material: 1.5 to 33%
Temperature: 0 to 50°C ( 32 to 122°F )
·Resolution: Wood and Building material: 0.1%
Temperature: 0 .1°C ( 0.1°F)
·Accuracy: Wood and Building material: ± 2%
Temperature: ± 2°C ( ± 4°F )
·8 calibration scales(A, B, C, D, E, F, G, H), based on different
types of wood materials.
·Hold function to freeze the measurement.
·Low battery indication(< 2.2V).
·Automatic Power-Off in 3 minutes without operation.
·Operated Power: 2xLR03 AAA 1.5V batteries.
·Working current: <35mA@3.0V
·Operating Environment: Temperature: 0 - 40°C
Relative Humidity < 85%RH
INSTALLING BATTERY:
1. Remove the battery compartment cover.
2. Insert the batteries with the correct polarity.
3. Reattach the battery compartment cover.
REMOVING PROTECTIVE CAP:
To remove the protective cap, press the “ ” position and
push the cap as the illustration below to open the cap.
OPERATION INSTRUCTION:
1.Press the “ ” button to turn on the instrument, press and
hold the “ ” button for about 3 seconds to turn off the
instrument.
2.Selecting desired Measurement Mode:
a. After turn on the instrument, press the “ ” button to
select desired measurement mode.
The two measurement modes are as follows:
Wood moisture measurement mode (“WOOD” displays),
building material moisture measurement mode (“BLDG”
displays).
Wood moisture measurement mode has 8 calibration scales(A,
B, C, D, E, F, G, H), based on different types of wood materials.
Check the Calibration Tables first, and then press the “ ”
button to switch to the matched calibration scale.
b. After the desired measurement mode is selected, you can
start measurement.
c.Temperature measurement mode displays in Celsius
temperature
measurement mode ( “°C” displays) or Fahrenheit temperature
measurement mode ( “°F” displays).
Press “ ” button to switch between °C and °F.
3.Performing Measurement
a. For temperature measurement, the display shows the present
environment temperature directly.
b. Before taking the first measurement check that the instrument
is functioning correctly.
For this you will need to use the Test Aid.
On the Test Aid there are two measurement holes as picture.
Switch to Wood moisture measurement mode (“WOOD”
displays) and choose A scale.
Insert the measuring pins into the measurement holes, the
measuring value on the display will show between 16.6% to
20.6%.
The instrument is workable when measured value was in the
error range.
c.To perform moisture measurement, press both pins into the
wood or material to be measured, read the value on the display.
d. Measured value will appear on the LCD, and Red, Yellow,
Green LED color light indicate the moisture condition level at
the same time.
Wood: Green: Low moisture (< 12%);
Yellow: Mid moisture (12% - 15.9%);
Red: High moisture (16%-60%).
Building material: Green: Low moisture (< 17%);
Yellow: Mid moisture (17% - 19.9%);
Red: High moisture (20%-33%)
4. Freeze the measurement
Press the “ ” button to saved measured value, the “HOLD”
will show on the screen. By pressing the “ ” or “ ” or
“” button, the measuring mode will get reactivated.
5. Automatic Power-Off feature
If you don’t operate the instrument (or the reading does not
change) about 3 minutes, the instrument will be turned off
automatically.
6.When the symbol “ ” appears, it indicates the batteries
are low and should be replaced.
MAINTENANCE:
The moisture meter has been designed to be a low maintenance
instrument.
However, in order to maintain its performance, you must always
follow these simple directions:
• AVOID exposing the instrument to shock, continuous vibration,
or extreme hot or cold temperatures.
• ALWAYS attach the protective cap when not in use.
• ALWAYS keep the instrument free of dust and liquids.
• Check the battery regularly to avoid deterioration.
• ALWAYS remove the battery when storing the instrument.
• DO NOT attempt to change any part of the unit.
• DO NOT disassemble the instrument. This will void the
warranty.
• Store the instrument in a dry location.
• After measurement, clean the probes and the case using a
clean cloth.
LCD Moisture Meter
TH PROT CT R
by R
R
THEPROTECTOR LIMITED PRODUCT WARRANTY
Please take the time to read through our Standard Terms and Conditions of the THEPROTECTOR Limited
Product Warranty.
How Long Does The Coverage Last?
This warranty applies only the device. The product warranty becomes eective from the date of purchase
by the purchaser. Coverage terminates if you sell or otherwise transfer the product. The repair of your
product under warranty will not extend the period of the warranty. Each part has its own warranty. Please
check the warranty list before you place an order.
How Do You Get Service?
Products are to be returned to THEPROTECTOR Tech Support Center under your express account. Address:
10725 Capital St. Oak Park. MI +1 248-542-1831
What is Covered?
Normal wear and tear.We will repair or replace your product if your product is found, within the warranty
period, to be defective due to defective materials or workmanship existing at the time of purchase. If any
part is no longer available or out of manufacture, THEPROTECTOR will replace it with a functionally-equiva-
lent replacement part.
What is Not Covered?
THEPROTECTOR shall NOT be liable for costs of repair or replacement of a product incurred as a result of:
1. Accidental damage, faults caused by negligent use or care, neglect, careless operation or handling of
the product which is not in accordance with the THEPROTECTOR Instruction Manuals.
2. Use of the parts not assembled or installed in accordance with the instructions of THEPROTECTOR.
3. Use of parts or accessories other than those produced or recommended by THEPROTECTOR.
4. External sources such as transit damage or weather.
5. Repairs or alterations carried out by parties other than THEPROTECTOR or its authorized agents.
6. Serial numbers defaced or missing.
THEPROTECTOR warrants the mechanical and electronic components of all THEPROTECTOR series to be
free of defects in material and workmanship if used under normal operating conditions for a period from
the original date of purchase. If the product shows any defects within this period and that defect is not due
to user error or improper use THEPROTECTOR shall, at its discretion, either replace or repair the product
using suitable new or refurbished parts. In case THEPROTECTOR decides to replace the entire product, this
limited warranty shall apply to the replacement product for the remaining initial warranty period.
THEPROTECTOR DISCLAIMS ANY AND ALL LIABILITY, INCLUDING ANY EXPRESS OR IMPLIED WARRANTIES, WHETHER ORAL OR WRITTEN, FOR SUCH
THIRD PARTY HARDWARE. THE CUSTOMER ACKNOWLEDGES THAT THEPROTECTOR HAS MADE ITS BEST EFFORTS TO MATCH ITS PRODUCTS TO WORK
WITH THIRD PARTY HARDWARE OR THE ABILITY TO CONNECT TO AND CONTROL THIRD PARTY HARDWARE FOR THE CUSTOMER’S INTENDED PURPOSE.
THEPROTECTOR ADDITONALY AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILTY FOR CHANGES, ADDITIONS OR UPDATES IN ANY WAY TO A THIRD
PARTY MANUFACTURES PRODUCTS.
Moisture Meter LCD
Innovative Tool and Design, Inc.
10725 Capital St Oak Park MI 48237 USA
www.shoptheprotector.com
