InSinkErator Model SS-200 User manual

Part No. 13954 Rev.A
FOODSERVICE DISPOSER
Installation Manual
www.insinkerator.com/foodservice
Please be certain that the person who installs or uses this appliance carefully reads
and understands the Safety Instructions contained in this manual.
The Danger signal indicates an immediately hazardous situation which, if not
avoided, will result in death or serious injury.
The Warning signal alerts you to potential hazards or unsafe practices which,
if not avoided, could result in severe personal injury or death.
The Caution signal alerts you to hazards of unsafe practices which, if not avoided,
may result in minor personal injury or property damage.

2
Table of Contents
Introduction
Introduction .................................................................................... 3
Clean the Drain Line ....................................................................... 3
Typical Installation .......................................................................... 3
Required Tools/Materials ................................................................ 3
Installing the Disposer
Disposer Mounting ......................................................................... 4
Mounting Adaptors ........................................................................ 4
Standard InSinkErator Mountings
#5 Mounting Assembly .................................................................. 5
#6, 7, and Sink Bowl Mounting Assemblies ................................... 6
Special InSinkErator Mountings ................................................................. 6
Plumbing Connections
Drain Line Connections .................................................................. 7
Water Supply Connections ............................................................ 7
Routing Water Flow ......................................................................... 7
Standard Motor Connection Wiring Diagrams .......................................... 8
Electrical Connections
Electrical Connections ................................................................... 9
Disposer Controls ........................................................................... 9
Operating Instructions
Operating the Disposer ................................................................ 10
Grinding Tips ................................................................................ 10
Troubleshooting .......................................................................................... 11
Warranty
FOODSERVICE DISPOSER LIMITED WARRANTY
The InSinkErator® Foodservice Disposers are warranted against defects in material and workmanship for one year
from the date of installation. The warranty includes parts and labor, provided the service is performed by an
InSinkErator Factory Authorized Service Center. This warranty does not apply if failure is due to: faulty or improper
electrical installation, faulty or improper plumbing installation, product abuse or misuse, accidental damage, grinding
elements jammed by foreign objects, clogged drain lines, or an improperly sized unit (as specified by InSinkErator).
InSinkErator Foodservice disposer accessories are included in this warranty only if they are included in the original
disposer purchase package.

Introduction
3
INTRODUCTION
The InSinkErator Foodservice food waste disposer is
UL® and CSA® Listed when installed in conjunction with
InSinkErator mounting adaptors and controls (see Figure
1 for typical installation).
See Table 1 (page 4) for the approved disposer/
mounting adaptor combinations. See Table 3 (page 9)
for the approved disposer/control combinations.
Important – These installation instructions are for
the benefit of the installing contractor. InSinkErator
and/or InSinkErator Factory Authorized Service
Centers do not make original installations. For technical
information not covered in these instructions,
contact the supplier, an InSinkErator Field Sales
Representative, or InSinkErator Foodservice Sales
and Service at 1-800-845-8345.
CLEAN THE DRAIN LINE
With a drain line auger, clear away all hardened waste
material in the horizontal drain pipe running from the
drain trap to the main waste line.
TYPICAL INSTALLATION
A typical Foodservice disposer installation incorporates
the following connections (see Figures 1 and/or 9):
• Water shut off valve
• Syphon breaker
• Solenoid valve
• Start/stop switch (Control Center)
• Sink or trough
• Flow control valve
REQUIRED TOOLS/MATERIALS
The following items are needed to install the disposer:
• Screwdriver
• Adjustable wrench
• Pipe wrench
• Wire nuts
• 7/16" nut driver
The following items may be needed to install
the disposer:
• Plumbing putty
• Hacksaw
• Drain auger
Figure 1. Typical Installation

Installing the Disposer
4
Figure 2. Distance from Table Top to Mounting Flange
MOUNTING ADAPTORS
There are two adaptor categories for mounting InSinkErator disposers: Standard & Special Mountings.
Table 1 displays the approved disposer/mounting adaptor combinations.
PROPERTY DAMAGE
To avoid excess vibration, InSinkErator
recommends a minimum countertop thickness
of 16 gage stainless steel.
PERSONAL INJURY
• For safe operation, install the disposer in
compliance with the minimum distance illustrated
in Figure 2.
• Disposer must be properly installed to prevent
serious injury from moving shredder part.
Adaptor SS-50 SS-75 SS-100 SS-125 SS-150 SS-200 SS-300 SS-500 SS-750 SS-1000
12" Sink
15" Sink
18" Sink
No. 5
No. 5 short
No. 6
No. 7
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
O
X
X
X
X
X
O
O
X
X
X
X
X
O
O
X
X
X
X
X
O
O
X
X
SPECIAL STANDARD
Outward
Flange
Inward
Flange
Straight
Flange
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 1. Foodservice Disposer/Mounting Adaptor Combinations X= Approved
O= Not Allowed
(will void warranty)
DISPOSER MOUNTING
7-3/8"
(187.33 mm)
7-3/4"
(196.85 mm)
2-3/4"
(69.85 mm)
18-7/16"
(468.31 mm)
2"
(50.80 mm)
24-1/4"
TO
32-1/2"
(615.95 mm
TO
825.50 mm)
(WITH
OPTIONAL
LEGS
INSTALLED)
24-4/5"
TO
33-4/5"
(629.92 mm
TO
858.92 mm)
(WITH
OPTIONAL
LEGS
INSTALLED)
23-3/4"
TO
31-1/8"
(603.25 mm
TO
790.58 mm)
6-13/16"
(173.04 mm)
6-13/16"
(173.04 mm)
4-7/8"
(123.83 mm)
6-3/8"
(161.93 mm)
1-1/2"
(38.10 mm)
3-3/8"
(85.73 mm)
6-1/2"
(165.10 mm)
7-11/16"
(195.26 mm)
17"
(431.80 mm)
8-3/4"
(222.25 mm)
8-3/4"
(222.25 mm)
7-1/8"
(180.98 mm)
13"
(330.20 mm)
3"
(76.20 mm)
SS-50 to SS-125 SS-150 to SS-200 SS-300 to SS-1000
6-5/8"
(168.28 mm)
6-1/2"
(165.10 mm)
6-5/8"
(168.28 mm)
6-1/2"
(165.10 mm)
6-5/8"
(168.28 mm)

5
Standard InSinkErator Mountings
#5 MOUNTING ASSEMBLY
Follow these instructions to install a #5 sink flange to a
standard 3-1/2 to 4 inch sink opening.
1. Unscrew the three backup screws (6) until they are
flush with the upper mounting flange (5) surface. Pry
the retainer ring (7) free from the strainer flange (2)
with a screwdriver and separate all mounting
assembly parts (2-7).
2. Form a 3/4" thick ring of top grade oil base putty
around the sink opening (use a non-hardening putty).
Insert the strainer flange (2) into the sink opening and
press firmly in place. Clean away any excess putty.
3. From underneath the sink, place the strainer flange
gasket (3), back up flange (4) - flat side up, and upper
mounting flange (5) over the strainer flange and hold
them up to the sink. Snap the retainer ring (7) into the
groove on the strainer flange to hold the mounting
parts in place.
4. Tighten the three backup screws evenly until the
backup flange draws snugly against the underside
of the sink and the strainer flange is held securely
in place.
5. Place the body flange (9 - lugs upward) over the lip of
the mounting flange (10) and fit the mounting
gasket (8) onto the lip.
6. Place the mounting gasket (11) on the disposer body
flange. Secure the mounting flange (10) to the
disposer body flange with six screws (12) provided.
7. Raise the disposer to the upper mounting flange (5)
so the body flange (9) is positioned with the lugs to
the right of the screws.
8. While supporting the disposer, turn the body flange
(9) to the right until all three lugs are engaged in the
mounting flange (5). Swivel the disposer to align the
discharge outlet with the drain tap. The disposer can
be turned 360 degrees.
9. Align the disposer to the plumbing connection and
insert the service wrench into the left side of a lug
and continue to turn the body flange to the right
(approximately one quarter turn) until it locks onto the
notches on the upper mounting flange.
NOTE: Special mounting instructions are included in the
#5 Short Mounting Kit.
Figure 3. #5 Mounting Assembly
(1) Stopper
(2) Strainer Flange
Sink*
(3) Strainer Flange Gasket
(4) Backup Flange
(5) Upper Mounting Flange
(6) Backup Screw
(7) Retaining Ring
(8) Mounting Ring
(9) Body Flange
(10) Mounting Flange
(11) Mounting Gasket
Disposer Body Flange*
(12) 1/4" Screw
* Not included as part of #5 mounting

6
Standard InSinkErator Mountings
1. Place the mounting flange (1) over the existing collar
adaptor connection lip or sink bowl flange (this may
require some force).
2. Push the mounting flange up out of the way and fit
the groove in the mounting gasket (2) onto the
connection lip. Make sure the gasket is fully seated
on the flange.
3. Push the mounting flange down over the mounting
gasket, fitting the threaded mounting flange fasteners
into the recesses in the top of the mounting gasket.
#6, #7, & SINK BOWL MOUNTING ASSEMBLIES
4. From the bottom, insert two screws through opposite
sides of the flat gasket (3) and mounting flange, into
the threaded fasteners in the existing flange. The flat
gasket is used only in the #6 mounting assembly.
The screws should protrude about 1/4 inch below the
mounting gasket.
5. Position the disposer beneath the mounting gasket
and raise it to engage the two protruding screws in
the disposer body flange keyhole slots. Secure the
remaining screws and position the disposer correctly
for the plumbing connections. For SS150-SS1000
disposers, adjust the legs to support the disposer.
Figure 4. #6 Mounting Assembly Figure 5. #7 or Sink Bowl Mounting Assembly
Special InSinkErator Mountings
When installing an InSinkErator Foodservice disposer to a non-InSinkErator sink bowl, a special mounting adaptor kit
is required. The special mountings are described in the Mounting Adaptor Selection Guide (for more information, call
1-800-845-8345, or go to www.insinkerator.com). Figures 6-8 show examples of non-InSinkErator sinks. (Mounting
instructions are included in each special mounting adaptor kit.)
Figure 6. Outward Flange Figure 7. Inward Flange Figure 8. Straight Flange

7
PROPERTY DAMAGE
These plumbing instructions were written for an
experienced competent installer. If the installer
is not experienced in plumbing installation,
InSinkErator recommends that competent
professional assistance is sought. Damage to
the disposer or accessories as a result of
improper installation is not covered under
warranty. All installations must comply with local
plumbing codes.
Plumbing Connections
DRAIN LINE CONNECTIONS
To allow easy access to overload reset button, the
disposer plumbing should be connected with the
electrical control box facing the operator.
When connecting the drain line, place the "P-trap" as
close to the disposer outlet flange as possible. Do not
connect the drain line to a grease trap, interceptor, or
drum trap.
All horizontal runs should be as short as possible, with a
minimum fall of 1/4 inch per foot.
WATER SUPPLY CONNECTIONS
When connecting the disposer to the incoming water
supply, use as few elbows and tees as possible.
Connect to the cold water line only. All water line
fittings are 1/2" NPT except the sink bowl nozzles
(1/2" compression).
Install the flow control valve, water solenoid valve, and
the syphon breaker according to the direction of the
flow arrows marked on each valve body (see Figure 9).
NOTE: A syphon breaker must be installed above the
sink flood plane per local plumbing codes.
ROUTING WATER FLOW
• In a trough system, route all water flow to the end of
the trough to flush food waste.
• In a sink bowl system route all water through the
sink bowl.
• Table 2 provides Recommended Cold Water Flow and
Drain Line Diameter.
Disposer Standard
Flow Control
GPM (LPM)
Optional
Flow Control
GPM (LPM)
Drain
Line
Diameter
SS-50 3 (11) NA 1-1/2"
SS-75 3 (11) NA 1-1/2"
SS-100 5 (19) 3 (11) 1-1/2"
SS-125 5 (19) 3 (11) 2" NPT
SS-150 7 (26) 5 (19) 2" NPT
SS-200 7 (26) 5 (19) 2" NPT
SS-300 8 (30) 7 (26) 3" NPT
SS-500 8 (30) 7 (26) 3" NPT
SS-750 10 (38) NA 3" NPT
SS-1000 10 (38) NA 3" NPT
Table 2. Recommended Cold Water Flow
and Drain Line Diameter
Figure 9. Installation Diagram

8
Standard Motor Connection Wiring Diagrams
NOTE: The diagrams below show standard motor connection wiring for a manual switch operation. For alternate
controls, please refer to the control panel installation manual.
4 5 6
MOTOR LEAD WIRE#
L2
2
L1
7
31
L1 L2 L3
1
4 10 5 6 12
MOTOR LEAD WIRE#
11
7 2 8 3 9
2 3 4
MOTOR LEAD WIRE#
L1
7
L2
1
5 6
1
4 7 5 6 9
MOTOR LEAD WIRE#
L1 L2 L3
8
2 3 10 11 12
Figure 12. Incoming 208-230V Three Phase Line Power
Figure 10. Incoming 115V Single Phase Line Power Figure 11. Incoming 208-230V Single Phase Line Power
Figure 13. Incoming 460V Three Phase Line Power

9
ELECTRICAL SHOCK
• Turn off the electrical supply to the disposer before
servicing. Test the circuit with a voltmeter or circuit
tester to ensure the power is off.
• Installation must conform to all local
electrical codes.
• All control centers and disposers must
be grounded.
• A properly fused disposer control (with a marked
"off" position) that disconnects all ungrounded
supply conductors must be installed at the
electrical supply source.
PROPERTY DAMAGE
• Disposers shipped from the factory are not wired
for a specific voltage. Refer to the motor
connection wiring diagram in the terminal box for
voltage instructions.
• Ensure the disposer motor voltage and phase
match that of the electrical supply.
• The disposer motor wiring connection is shown in
the disposer terminal box.
Electrical Connections
ELECTRICAL CONNECTIONS
To connect the disposer to the electricity:
1. Remove the screw in the center of the disposer
terminal box.
2. Pull the terminal box out of the stainless steel
trim shell.
3. Connect an electrical conduit connector to the hole in
the bottom of the exposed wiring compartment.
4. Connect the ground wire to the ground screw.
5. Connect the incoming wires to the motor leads. Make
sure the wiring connections are the same as those on
the electrical connection diagrams (see page 8).
6. Reinstall the terminal box cover on the trim shell.
7. Test the disposer to ensure the cutting elements
revolve and the water flows automatically. Make sure
the disposer is securely mounted and does not leak
from any of the connections.
ELECTRICAL SHOCK
Be careful not to pinch or damage the electrical
wires when installing the terminal box.
PERSONAL INJURY/PROPERTY DAMAGE
If the electrical installer is not experienced in
electrical installation, we recommend seeking
competent professional assistance. Disposer or
accessory damage due to improper installation is
not covered under warranty. All installations must
comply with local electrical codes.
NOTES:
• Pressure switches may be connected across the
line at 5 horsepower or less. Large horsepower
motors require connection in the pilot circuit of a
magnetic starter.
• The magnetic and manual starters supplied by
InSinkErator do not require heaters to complete the
circuit. InSinkErator disposers are equipped with
overload protectors.
• A time delay may only be used with a water
solenoid valve.

10
Operating Instructions
OPERATING THE DISPOSER
1. Make sure there are no foreign objects in the
disposer grind chamber. Do not pre-load the
disposer with food waste prior to starting.
2. Push the start button on the control switch. The
disposer will run and water will flow into the disposer.
3. Feed food waste into the disposer in a steady,
continuous flow.
4. When all food waste is flushed away, push the stop
button on the control switch.
NOTE: The Manual Reversing Switch uses three-
button operation (FWD/STOP/REV) to manually change
disposer grind direction. The disposer will rotate in the
direction of the button pushed. DO NOT restart disposer
until the rotating shredder has come to a stop.
GRINDING TIPS
• Ensure that a steady stream of cold water runs into
the disposer while it is operating (see Table 2 for the
recommended cold water flow).
• Do not overload the disposer or turn it off with food
waste inside the grind chamber. Run the disposer and
water for three minutes after the final load to flush
away all food waste.
PROPERTY DAMAGE
Do not pre-load food waste into disposer before
turning on. Pre-loading disposer with food waste
can cause excessive strain and may loosen
disposer mounting components, resulting in
disposer separating from sink or trough.
FIRE HAZARD
To minimize the possibility of fire, do not store
flammable items near the disposer. Do not use
or store gasoline or other flammable liquids near
the disposer.
PERSONAL INJURY
• Food waste disposers are designed to grind
and dispose of normal food waste. Inserting
materials or items other than food waste into
the disposer could cause personal injury and/or
disposer damage.
• To reduce the risk of injury from materials that may
be expelled from the disposer grind chamber,
ensure that the disposer baffle is properly installed.
• To prevent the ejection of food waste and to keep
foreign materials out of the grind chamber, replace
the splash baffle when it becomes worn.
• Do not put any of the following items into the
disposer: clam or oyster shells, drain cleaner, glass,
china, plastic wrap, large bones, metal objects,
explosive materials, extremely hot water, grease,
oil, or syrup.
• Turn the power off before attempting to clear a jam,
remove an object, or press the reset button.
• Do not insert your fingers into the disposer. Use
long-handled tongs or pliers to remove objects
from the disposer.
• Loosen any jams with the dejamming bar.
• Be certain that all persons who will operate the
disposer read the safety and operating instructions
prior to operating the disposer.
• To prevent accidents, ensure that the disposer is
turned off before your leave the area.
ELECTRICAL SHOCK
• Disconnect the electrical supply before servicing
the disposer.
• Ensure the disposer and controls are
properly grounded.