INSPIRE Q Lynn User manual

2538-60(SPK) DINING TABLE
Table Top Table Leg Bolt
5/16" x 2-1/2"
Lock Washer
5/16"
Flat Washer
5/16"
Allen Key
1/4" x 2-3/8"
1pc 4pcs 8pcs 8pcs
8pcs 1pc
1
ASSEMBLY INSTRUCTION
This page lists all the contents included in
the box. Please take the time to identify the
hardware as well as the individual
components to this product. As you
unpack and prepare for assembly, place
the contents on a carpeted or padded area
to protect them from damage.

C
F
D
E
Attach the four Table Leg (B) to the Table Top (A) use Bolt (C), Lock Washer (D) and Flat
Washer (E) on four holes of the Table Top (A). Turn the Allen Key (F) in the Bolt (C). Hand
tighten only at this moment by using Allen Key (F).
Stand table up on an even surface and check that it is
balanced. If there is a slight wobble, apply downward
pressure in the corner where a leg is uneven. Keeping
pressure in that corner, tighten all bolts. If balanced,
apply downward pressure evenly in the center and
tighten all bolts. Do not over-tighten beyond hole depth.
B
A
2
Cleaning & Care:
Treat surface with care. Surface is resistant to scratches but is not scratch resistant. Clean
surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Hardware may loosen
over time. Periodically check that all connections are tight.
Take the Allen Key, and turn the bolts
until the legs are secure.
DO NOT TIGHTEN COMPLETELY.
Stop when you feel you are adding
force to tighten the bolt.
A
Phillips Head Screw Driver
Is Required But Not Included
Adjustable Shelf
Put Table Top (A) on smooth flat surface. Remove the four Adjustable Shelf with Phillips
Head Screw Driver (not Included).
A
B

2538S(SPK) SIDE CHAIR
Chair Back
This page lists all the contents included in
the box. Please take the time to identify
the hardware as well as the individual
components to this product. As you
unpack and prepare for assembly, place
the contents on a carpeted or padded area
to protect them from damage.
Seat With Cushion Front Leg Long Bolt
1/4" x 3"
Medium Bolt
1/4" x 2-1/2"
Short Bolt
1/4" x 1-1/2"
Lock Washer
5/16"
Flat Washer
5/16"
Allen Key
1/4" x 2-3/8"
1pc 1pc 2pcs 4pcs
4pcs 3pcs 11pcs 11pcs
1pc
ASSEMBLY INSTRUCTION
1

E
I
I
H
G
F
I
2
B
A
C
C
Put Chair Back (A) on smooth flat surface. Attach one Seat With Cushion (B) to the Chair
Back (A) use Long Bolt (D), Short Bolt (F), Lock Washer (G) and Flat Washer (H) on five
holes of the Chair Back (A). Turn the Allen Key (I) in the Long Bolt (D) and Short Bolt (F).
But not too tight.
Take the Allen Key, and turn the bolts
until the legs are secure.
DO NOT TIGHTEN COMPLETELY.
Stop when you feel you are adding
force to tighten the bolt.
Attach Front Leg (C) to the Seat With Cushion (B) use Medium Bolt (E), Lock Washer (G)
and Flat Washer (H) on both holes of the Seat With Cushion (B). Turn the Allen Key (I) in
the Medium Bolt (E). But not too tight.
Stand chair up on an even surface
and check that it is balanced. If
there is a slight wobble, apply
downward pressure in the corner
where a leg is uneven. Keeping
pressure in that corner, tighten all
bolts. If balanced, apply downward
pressure evenly in the center and
tighten all bolts. Do not over-tighten
beyond hole depth.
Cleaning & Care:
Treat surface with care. Surface is resistant to scratches but is not scratch resistant. Clean
surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Hardware may loosen
over time. Periodically check that all connections are tight.
B
Helpful Tip:
-Instead of applying downward pressure while
reaching under to tighten bolts, have someone
sit in the chair while you tighten the bolts.
C
B
B
A

2538-13(SPK) BENCH
This page lists all the contents included in
the box. Please take the time to identify
the hardware as well as the individual
components to this product. As you
unpack and prepare for assembly, place
the contents on a carpeted or padded
area to protect them from damage.
Bench Top Leg Nut
5/16" x 1/2"
Lock Washer
5/16"
Flat Washer
5/16"
Wrench
1/2" x 2-3/8"
1pc 4pcs 8pcs 8pcs
8pcs 1pc
1
ASSEMBLY INSTRUCTION

Put Bench Top (A) on smooth flat surface. Attach the four Leg (B) to the Bench Top (A)
use Nut (C), Lock Washer (D) and Flat Washer (E) on four holes of the Bench Top (A).
Turn the Wrench (F) in the Nut (C). Hand tighten only at this moment by using Wrench (F).
Take the Wrench, and turn the Nut
until the legs are secure.
DO NOT TIGHTEN COMPLETELY.
Stop when you feel you are adding
force to tighten the Nut.
Stand bench up on an even surface and check
that it is balanced. If there is a slight wobble, apply
downward pressure in the corner where a leg is
uneven. Keeping pressure in that corner, tighten all
nut. If balanced, apply downward pressure evenly
in the center and tighten all nut.
Do not over-tighten beyond hole depth.
A
B
E
D
C
F
2
Cleaning & Care:
Treat surface with care. Surface is resistant to scratches but is not scratch resistant. Clean
surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Hardware may loosen
over time. Periodically check that all connections are tight.
B
A