INSTEON 2867-222 User manual
Alert Module
Owner’s Manual
Alert Module
Owner’s Manual
Contents
Getting Started
Insteon Alert Module 4
Device Overview
Buttons
Installation
Alert Types 5
Triggering Alert Module from an Insteon Device 6
Local Programming
About Local Programming 8
Local Programming Flow Chart 9
Factory Reset
Factory Reset 11
Appendix
Specications 13
Troubleshooting 15
Certications and Warnings 16
Product Warranty 17
3
Everything you need to quickly get up and running.
Getting Started
Everything you need to quickly get up and running.
Getting Started
4
Installation
ButtonsDevice Overview
Insteon Alert Module
Set Button
Alert Speaker
Status LED
Armed
Disarmed
Plug Alert Module into an unswitched wall outlet.
Set Button
See sections on Local Programming
for set button functions
5
Instant Chime
Two short beeps will sound
the moment Alert Module is
triggered
Instant Loud Ringing
Loud ringing will sound the
moment Alert Module is triggered.
The loud ringing will persist for
30 seconds unless stopped by
disarming Alert Module.
Alert Types
Alert Module features two types of audible alerts. Choose the
suitable alert when creating a Scene using tap-tap linking.
6
Your Insteon device will
now trigger Alert Module
Triggering Alert Module from an Insteon Device
1On Alert Module, tap the set
button until you hear the desired
alert tone.
2On your Insteon device, press and
hold the set button until its LED
begins blinking.
3On Alert Module, press and hold
the set button until you hear a
double-beep.
4Test Alert Module by triggering
your sensor or turning on your
Insteon device.
7
Use the local programming to link Insteon devices together with the set button.
Local Programming
Use local programming to link Insteon devices together with the set button.
Local Programming
8
About Local Programming
Local Programming Features
Linking Mode Readies the module for linking to another Insteon device. As linking is directional, the rst
device placed into linking mode will become the controller in the controller/responder
relationship. The second device will become the responder. The device automatically exits
linking mode after a link has been made with another Insteon device or four minutes have
elapsed without linking.
Multi-Linking
Mode
Readies the module for linking to multiple Insteon devices. The module will remain in linking
mode for 4 minutes or until the module’s set button is tapped. This mode is very usefully for
manually creating scenes.
Unlinking
Mode
Allows the removal of links from the Insteon device. The device will automatically exit
unlinking mode after a link has been removed from another Insteon device or four minutes
have elapsed without linking.
Multi-
Unlinking
Mode
Allows the removal of multiple links from the Insteon device. The device will stay in unlinking
mode for 4 minutes or until the device’s set button is tapped.
To move right, press and
hold the set button
To move down, tap the set
button
Status LED blinks green
Status LED double-blinks
green
Status LED blinks red
Status LED double-blinks
red
The Local Programming Flowchart is a visual
representation of the device’s settings. Many
device features can be congured using this
diagram. Some devices have more options
than others but the Local Programming
Flowchart presents even the most
complicated devices with a straightforward,
navigable path.
If using the Insteon Hub or any other central
controller, it is strongly advised that you
not use Local Programming. Your central
controller can manage the device properties
and links for you.
NavigationLocal Programming
Using a Central Controller
NEW
X
9
Arm & Disarm
Instant Loud
Ringing
Instant Chime
Instant Loud
Ringing
TapTap Tap TapTap Tap
Press
Press
Press
Press
Unlinking
Mode
Multi-
Unlinking
Mode
Select
Linking Mode
Multi-Linking
Mode
Select
Press
Tap
Tap
PressPress
TapTap
ExitExit
ExitExit
Local Programming Flow Chart
Press
Exit
10
A factory reset will erase all links stored in the device’s database as well as
any customized properties.
Factory Reset
A factory reset will erase all links stored in the device’s database as well as
any customized properties.
Factory Reset
11
Your Alert Module has been
restored to factory settings.
Factory Reset
1Unplug Alert Module from its
power outlet 2Simultaneously press and hold the
set button while reconnecting Alert
Module to power
3Continue holding the set button
until Alert Module stops beeping 4When the reset is complete, Alert
Module will double-beep
12
Everything else you might need to know about your Insteon product.
Appendix
Everything else you might need to know about your Insteon product.
Appendix
13
Specications
General
Available Colors White
Brand: Insteon
FCC ID SBP29922
Industry Canada 5202A-29922
Manufacturer Product No.: 2867-222
Patent No.: Protected under US and Foreign Patents (see www.insteon.com/
patents)
UPC: 813922015652
Warranty: 2 years, limited
Operation
Audio Alert Beeper
Setup Memory Non-volatile EEPROM
Status LED Red/Green LED
Insteon Features
Insteon Device Category 0x07
Insteon Device Subcategory 0x1A
Insteon ID 1
Insteon Links 400
Insteon Messages Repeated Yes
Insteon Minimum Receive Level 10 mV
Insteon Minimum Transmit Level 3.2 Vpp into 5 Ohms
Insteon Powerline Device Yes
Insteon Powerline Frequency 131.65 KHz
Insteon RF Device Yes
Maximum Controlled Scenes 1
Maximum Scene Memberships 400
Multi-Link Support Yes
14
Multi-Unlink Support Yes
RF Beacon Yes
Radio Frequency 915.0 MHz
Radio Frequency Range 150 feet
Scene Commands Supported as
Controller
Fast-On Fast-O
Scene Commands Supported as
Responder
On O
Software Congurable Yes
Mechanical
Dimensions 3.2” H x 2.05” W x 1.05” D
81.2mm H x 53mm W x 26.6mm D
Enclosure Material UV stabilized plastic
Mounting Ungrounded, polarized electrical outlet, NEMA 1-15
Operating Environment Indoors
Operating Humidity Range 0-85% relative humidity, non-condensing
Operating Temperature Range 32º to 104º F
0º to 40º C
Set Button Yes
Storage Temperature Range -4º to 158º F
-20º to 70º C
Weight 3.3 oz
Electrical
Pass-through Outlet No
Power Consumption <0.75 Watts
Supply Voltage 120 Volts AC ± 10%, 60 Hertz, single phase
Surge Resistance Surges over 1,000 volts
16
Certications and Warnings
Read and understand these instructions before installing and retain them for future reference.
This product is not designed or approved for use on powerlines other than 120VAC, 50Hz or 60Hz, single
phase. Attempting to use this product on unapproved powerlines may have hazardous consequences.
• Use only indoors or in outdoor rated box
• This product may feel warm during operation. The amount of heat generated is within approved limits and
poses no hazards. To minimize heat buildup, ensure the area surrounding this product is as clear of clutter
as possible.
• Each Insteon product is assigned a unique Insteon I.D., which is printed on the product’s label.
• To reduce the risk of overheating and possible damage to other equipment, do not use this product to
control loads in excess of the specied maximum(s) or, install in locations with electricity specications
which are outside of the product’s specications. If this device supports dimming, please note that dimming
an inductive load, such as a fan or transformer, could cause damage to the dimmer, the load bearing
device, or both. If the manufacturer of the load device does not recommend dimming, use a non-dimming
Insteon device. USER ASSUMES ALL RISKS ASSOCIATED WITH DIMMING AN INDUCTIVE LOAD.
This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorise aux deux conditions suivantes: (1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est
susceptible d’en compromettre le fonctionnement.
CAUTION - To reduce the risk of overheating and possible damage to other equipment do not install to control
a receptacle, a motor-operated appliance, a uorescent lighting xture, or a transformer-supplied appliance.
Gradateurs commandant une lampe a lament de tungstene – an de reduire le risqué de surchaue et la
possibilite d’endommagement a d’autres materiels, ne pas installer pour commader une prise, un appareil a
moteur, une lampe uorescente ou un appareil alimente par un transformateur.
17
Product Warranty
Limited Warranty
Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date
of purchase, this product will be free from defects in material and workmanship and will perform in substantial
conformity to the description of the product in this Owner’s Manual. This warranty shall not apply to defects or
errors caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the
product does not perform as warranted above during the warranty period, Seller will either repair it, replace it,
or refund the purchase price, at its option, upon receipt of the product at the address below, postage prepaid,
with proof of the date of purchase and an explanation of the defect or error. The repair, replacement, or refund
that is provided for above shall be the full extent of Seller’s liability with respect to this product. For repair or
replacement during the warranty period, call 866-243-8022 with the Model # and Revision # of the device to
receive an RMA# and send the product, along with all other required materials to:
Insteon
ATTN: Receiving
16542 Millikan Ave.
Irvine, CA 92606-5027
Limitations
The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or
implied, including any warranty or merchantability or tness for a particular purpose. Any implied warranty,
including any warranty of merchantability or tness for a particular purpose, which may not be disclaimed
or supplanted as provided above shall be limited to the two-year of the express warranty above. No other
representation or claim of any nature by any person shall be binding upon Seller or modify the terms of the
above warranty and disclaimer.
Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical
tampering. For optimal use, manually verify the device state. Any home automation device should be viewed as
a convenience, but not as a sole method for controlling your home.
In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from
possession or use of this device, including without limitation damage to property and, to the extent permitted by
law, personal injury, even if Seller knew or should have known of the possibility of such damages. Some states
do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of damages, in
which case the above limitations and/or exclusions may not apply to you. You may also have other legal rights
that may vary from state to state.
Protected under U.S. and foreign patents (see www.insteon.com/patents)
© Copyright 2015 Insteon
Rev 11.20.15
Table of contents
Other INSTEON Security System manuals
