Instron 2710-11 Series User manual

Instron Series 2710-11x Screw Action Grips
Reference Manual - Equipment M16-16348-EN Revision C
The difference is measurable
®

Electromagnetic Compatibility
Where applicable, this equipment is designed to comply with International Electromagnetic Com-
patibility (EMC) standards.
To ensure reproduction of this EMC performance, connect this equipment to a low impedance
ground connection. Typical suitable connections are a ground spike or the steel frame of a building.
Proprietary Rights Notice
This document and the information that it contains are the property of Illinois Tool Works Inc.
(ITW). Rights to duplicate or otherwise copy this document and rights to disclose the document and
the information that it contains to others and the right to use the information contained therein may
be acquired only by written permission signed by a duly authorized officer of ITW.
Trademarks
Instron® is a registered trademark of Illinois Tool Works Inc. (ITW). Other names, logos, icons and
marks identifying Instron products and services referenced herein are trademarks of ITW and may
not be used without the prior written permission of ITW.
Other product and company names listed are trademarks or trade names of their respective
companies.
Copyright © 2011 Illinois Tool Works Inc. All rights reserved. All of the specifications
shown in this document are subject to change without notice.
Worldwide Headquarters
Instron
825 University Avenue
Norwood, MA 02062-2643
United States of America
European Headquarters
Instron
Coronation Road
High Wycombe, Bucks HP12 3SY
United Kingdom
Industrial Products Group
Instron
900 Liberty Street
Grove City, PA 16127
United States of America

iii
Preliminary Pages
Product Support: www.instron.com
General Safety Precautions
Materials testing systems are potentially hazardous.
Materials testing involves inherent hazards from high forces, rapid motions, and
stored energy. You must be aware of all moving and operating components in the
testing system that are potentially hazardous, particularly force actuators or a
moving crosshead.
Carefully read all relevant manuals and observe all Warnings and Cautions. The
term Warning is used where a hazard may lead to injury or death. The term Caution
is used where a hazard may lead to damage to equipment or to loss of data.
Instron products, to the best of its knowledge, comply with various national and
international safety standards, in as much as they apply to materials and structural
testing. We certify that our products comply with all relevant EU directives (CE
mark).
Because of the wide range of applications with which our instruments are used, and
over which we have no control, additional protection devices and operating
procedures may be necessary due to specific accident prevention regulations, safety
regulations, further EEA directives or locally valid regulations. The extent of our
delivery regarding protective devices is defined in your initial sales quotation. We
are thus free of liability in this respect.
At your request, we will gladly provide advice and quotations for additional safety
devices such as protective shielding, warning signs or methods of restricting access
to the equipment.
The following pages detail various general warnings that you must heed at all times
while using materials testing equipment. You will find more specific Warnings and
Cautions in the text whenever a potential hazard exists.
Your best safety precautions are to gain a thorough understanding of the equipment
by reading your instruction manuals and to always use good judgement.
It is our strong recommendation that you should carry out your own product safety
risk assessment.

Preliminary Pages
iv M16-16348-EN
Warnings
Flying Debris Hazard - Make sure that test specimens are installed correctly
in grips or fixtures in order to eliminate stresses that can cause breakage of
grip jaws or fixture components.
Incorrect installation of test specimens creates stresses in grip jaws or fixture
components that can result in breakage of these components. The high energies
involved can cause the broken parts to be projected forcefully some distance from
the test area. Install specimens in the center of the grip jaws in line with the load
path. Insert specimens into the jaws by at least the amount recommended in your
grip documentation. This amount can vary between 66% to 100% insertion depth;
refer to supplied instructions for your specific grips. Use any centering and
alignment devices provided.
High/Low Temperature Hazard - Wear protective clothing when handling
equipment at extremes of temperature.
Materials testing is often carried out at non-ambient temperatures using ovens,
furnaces or cryogenic chambers. Extreme temperature means an operating
temperature exceeding 60 °C (140 °F) or below 0 °C (32 °F). You must use
protective clothing, such as gloves, when handling equipment at these temperatures.
Display a warning notice concerning low or high temperature operation whenever
temperature control equipment is in use. You should note that the hazard from
extreme temperature can extend beyond the immediate area of the test.
Crush Hazard - Take care when installing or removing a specimen, assembly,
structure, or load string component.
Installation or removal of a specimen, assembly, structure, or load string component
involves working inside the hazard area between the grips or fixtures. When
working in this area, ensure that other personnel cannot operate any of the system
controls. Keep clear of the jaws of a grip or fixture at all times. Keep clear of the
hazard area between the grips or fixtures during actuator or crosshead movement.
Ensure that all actuator or crosshead movements necessary for installation or
removal are slow and, where possible, at a low force setting.

v
Preliminary Pages
Product Support: www.instron.com
Explosion Hazard - Wear eye protection and use protective shields or screens
whenever any possibility exists of a hazard from the failure of a specimen,
assembly or structure under test.
Wear eye protection and use protective shields or screens whenever a risk of injury
to operators and observers exists from the failure of a test specimen, assembly or
structure, particularly where explosive disintegration may occur. Due to the wide
range of specimen materials, assemblies or structures that may be tested, any hazard
resulting from the failure of a test specimen, assembly or structure is entirely the
responsibility of the owner and the user of the equipment.
Warnings

Preliminary Pages
vi M16-16348-EN

vii
Preliminary Pages
Product Support: www.instron.com
Table of Contents
Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Grip Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Grip Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Gripping Train . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Jaw Faces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Specimen Centering Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Chapter 2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Grip Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Grip Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Compatible Jaw Faces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Chapter 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Installing onto a Load Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Installing and Removing Jaw Faces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Install Jaw Faces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Remove Jaw Faces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Installing the Specimen Centering Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Preload the Load String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
To preload the load string: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
To unload the load string: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Chapter 4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Installing a Specimen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Removing a Specimen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Preliminary Pages
viii M16-16348-EN
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Chapter 5 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
General Maintenance Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Maintenance Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Replacing the Bearing Washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Chapter 6 Illustrated Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Replaceable Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Assemblies and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

1-1
Chapter 1
Introduction
•Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
•Grip Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Description
Instron Series 2710-11x screw action grips are designed for static tensile testing only. For
grips with capacities of 1kN or greater, clamping is achieved by tightening the screw knobs
using a hex key or torque wrench to provide adequate clamping force. The lower capacity
grips (100N and 500N) should only be tightened by hand. The grips are available in the
following capacities:
The grip bodies for the 100N, 500N, 1kN, 2kN and 5kN grips are fabricated in aluminum.
The grip bodies for the 10kN grips are fabricated in steel and can be used at higher
temperatures (refer to “Grip Specifications” on page 2-1).
The grips can be equipped with a variety of interchangeable grip jaw faces in various sizes
and surface types. Refer to Table 2-3 on page 2-4 to find compatible jaw faces for your
specific grip model. Contact your Instron sales representative for assistance with selecting
jaw faces that are suitable for your testing requirements.
Catalog number Capacity
2710-111 100 N (22.5 lbf)
2710-112 500 N(112 lbf)
2710-113 1 kN(225 lbf)
2710-114 2 kN(450 lbf)
2710-115 5 kN(1124 lbf)
2710-116 10 kN(2248 lbf)

Chapter: Introduction
1-2 M16-16348-EN
Grip Components
Grip Body
The U-shaped grip body is designed to provide compliance in the gripping train. This
produces a follow-up action in the gripping train that compensates for any decay in
clamping force caused by the thinning of specimens during testing. The front of the body has
two mounting holes for attaching the optional specimen centering device.
Figure 1-1. Grip Components
Shoulder screw
Jaw holder
Adapter
Screw knob
Anti-rotation pin
Anti-rotation slot
Jaw face
Specimen centering
device (optional)
Lock nut
Grip body
Bearing washer

1-3
Description
Product Support: www.instron.com
Adapter
The 100N, 500N, 1kN and 2kN grips connect to the load frame by a type Om adapter with a
6mm (0.25in) clevis pin.
The 5kN and 10kN grips connect to the load frame by a type Dm adapter with a 13mm
(0.5in) clevis pin.
Gripping Train
The gripping train consists of the screw knob, bearing washer, shoulder screw and jaw
holder. The screw knob provides the clamping force when tightened. The shoulder screw
connects the screw knob to the jaw holder and facilitates retraction of the jaw holder when
loosening the screw knob. Graduated markings are engraved on the jaw holder to aid in
centering specimens. An anti-rotation pin engages the slot in the jaw holder to prevent its
rotation when tightening or loosening the screw knobs. The bearing washer, which is
sandwiched between the jaw holder and the screw knob, minimizes friction between the
screw knob and the jaw holder.
Jaw Faces
The 2710-11x series screw action grips feature a new jaw face attachment mechanism that
greatly simplifies the task of changing jaw faces. Refer to “Installing and Removing Jaw
Faces” on page 3-2.
Specimen Centering Device
The optional specimen centering device is a small metal clamp with two thumbscrews that
attach to the front of the grip body. A knurled thumbscrew secures the specimen stop. The
specimen stop is a thin L-shaped arm, which extends outward across the jaw faces. The
extension of the specimen stop adjusts to accommodate different specimen widths.
The specimen stop lets you set the forward-to-back position of a specimen in the grips. The
forward-to-back position of same-sized specimens in the grips can then be repeated to
ensure consistent results.

Chapter: Introduction
1-4 M16-16348-EN

2-1
Chapter 2
Specifications
•Grip Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
•Grip Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
•Compatible Jaw Faces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Grip Specifications
Table 2-1. Grip Specifications
2710-111 2710-112 2710-113 2710-114 2710-115 2710-116
Load capacity 100 N
(22.5 lbf)
500 N
(112 lbf)
1 kN
(225 lbf)
2 kN
(450 lbf)
5 kN
(1124 lbf)
10 kN
(2248 lbf)
Test Application Tensile
Mechanical
connection
(upper and lower)
Type Om
6 mm (0.24 in)
clevis pin
Type Dm
12.7 mm (0.5 in)
clevis pin
Maximum
specimen
thickness
Varies according to jaw face, refer to Tab l e 2-3 on page 2-4
Maximum torque
that can be
applied to the
screw knobs
0.4 Nm
(hand-
tighten only)
2 Nm
(hand-
tighten only)
8 Nm
(5.9 lbft)
16 Nm
(11.8 lbft)
40 Nm
(29.5 lbft)
80 Nm
(59.0 lbft)
Grip body
material
Aluminum Steel
Temperature
range
-70°C to +125°C (-94°F to +257°F) -70°C to
+200°C (-
94°F to
+392°F)
Weight (each
grip, excluding
jaw faces)
0.45 kg
(1.0 lb)
0.55 kg
(1.2 lb)
1.15 kg
(2.54 lb)
1.15 kg
(2.54 lb)
2.68 kg
(5.91 lb)
4.91 kg
(10.82 lb)

Chapter: Specifications
2-2 M16-16348-EN
Grip Dimensions
Table 2-2. Grip Dimensions - mm (in)
Dimension - mm (in)
Label on
Figure 2-1 2710-111 2710-112
2710-113
and 2710-
114
2710-115
and 2710-
116
Effective height A 94 (3.68) 98.6 (3.86) 116.5 (4.59) 155.5 (6.12)
Maximum overall width (with
jaw face fully retracted)
B 173 (6.81) 196 (7.71) 225 (8.86)
Throat depth C 37.5 (1.48) 42.5 (1.67) 55.0 (2.17)
Throat depth D 12.5 (0.49) 17.5 (0.69) 25.0 (0.98)
Depth E 25 (0.98) 35.0 (1.38) 50.0 (1.97)
Hex socket size (across
flats)
F n/a 10 12
Maximum jaw face opening
with serrated faces (basic
opening)a
G 35 (1.42) 36 (1.42) 44 (1.73)
a. Opening depends on the type of jaw face used. Refer to Table 2-3 on page 2-4 for maximum specimen thicknesses.

2-3
Grip Dimensions
Product Support: www.instron.com
Figure 2-1. Grip Dimensions

Chapter: Specifications
2-4 M16-16348-EN
Compatible Jaw Faces
Table 2-3. Compatible Jaw Faces for 1kN, 2kN, 5kN and 10kN Grips
Catalog
No.
Surface Width -
mm (in)
Height -
mm (in)
Maximum Specimen Thickness
- mm (in)
2710-113 and
2710-114
2710-115 and
2710-116
2702-300 Rubber 25 (1.0) 25 (1.0) 34 (1.34) 44 (1.73)
2702-301 Rubber 25 (1.0) 38 (1.5) 34 (1.34) 44 (1.73)
2702-302 Rubber 25 (1.0) 51 (2.0) 34 (1.34) 44 (1.73)
2702-303 Rubber 38 (1.5) 13 (0.5) 34 (1.34) 44 (1.73)
2702-304 Rubber 38 (1.5) 25 (1.0) 34 (1.34) 44 (1.73)
2702-305 Rubber 38 (1.5) 51 (2.0) 34 (1.34) 44 (1.73)
2702-306 Rubber 51 (2.0) 25 (1.0) 34 (1.34) 44 (1.73)
2702-307 Rubber 51 (2.0) 38 (1.5) 34 (1.34) 44 (1.73)
2702-308 Rubber 51 (2.0) 51 (2.0) 34 (1.34) 44 (1.73)
2702-309 Rubber 76 (3.0) 25 (1.0) 34 (1.34) 44 (1.73)
2702-310 Rubber 76 (3.0) 51 (2.0) 29 (1.41) 39 (1.54)
2702-311 Rubber 152 (6.0) 51 (2.0) 29 (1.41) 39 (1.54)
2702-315 Serrated 25 (1.0) 25 (1.0) 36 (1.42) 46 (1.81)
2702-316 Serrated 25 (1.0) 38 (1.5) 36 (1.42) 46 (1.81)
2702-357 Serrated 25 (1.0) 51 (2.0) 31 (1.22) 41 (1.61)
2702-318 Serrated 38 (1.5) 13 (0.5) 36 (1.42) 46 (1.81)
2702-319 Serrated 38 (1.5) 25 (1.0) 36 (1.42) 46 (1.81)
2702-320 Serrated 38 (1.5) 51 (2.0) 36 (1.42) 46 (1.81)
2702-321 Serrated 51 (2.0) 25 (1.0) 36 (1.42) 46 (1.81)
2702-322 Serrated 51 (2.0) 38 (1.5) 36 (1.42) 46 (1.81)
2702-323 Serrated 51 (2.0) 51 (2.0) 36 (1.42) 46 (1.81)

2-5
Grip Dimensions
Product Support: www.instron.com
2702-324 Serrated 76 (3.0) 25 (1.0) 36 (1.42) 46 (1.81)
2702-325 Serrated 76 (3.0) 51 (2.0) 31 (1.22) 41 (1.61)
2702-326 Serrated 152 (6.0) 51 (2.0) 31 (1.22) 41 (1.61)
2702-330 Smooth 25 (1.0) 25 (1.0) 36 (1.42) 46 (1.81)
2702-331 Smooth 25 (1.0) 38 (1.5) 36 (1.42) 46 (1.81)
2702-332 Smooth 25 (1.0) 51 (2.0) 36 (1.42) 46 (1.81)
2702-333 Smooth 38 (1.5) 13 (0.5) 36 (1.42) 46 (1.81)
2702-334 Smooth 38 (1.5) 25 (1.0) 36 (1.42) 46 (1.81)
2702-335 Smooth 38 (1.5) 51 (2.0) 36 (1.42) 46 (1.81)
2702-336 Smooth 51 (2.0) 25 (1.0) 36 (1.42) 46 (1.81)
2702-337 Smooth 51 (2.0) 38 (1.5) 36 (1.42) 46 (1.81)
2702-338 Smooth 51 (2.0) 51 (2.0) 36 (1.42) 46 (1.81)
2702-339 Smooth 76 (3.0) 25 (1.0) 36 (1.42) 46 (1.81)
2702-340 Smooth 76 (3.0) 51 (2.0) 31 (1.22) 41 (1.61)
2702-341 Smooth 152 (6.0) 51 (2.0) 31 (1.22) 41 (1.61)
2702-345 Brake Lining
(HFC)
25 (1.0) 38 (1.5) 33 (1.30) 43 (1.69)
2702-346 Brake Lining
(HFC)
38 (1.5) 25 (1.0) 33 (1.30) 43 (1.69)
2702-347 Brake Lining
(HFC)
51 (2.0) 38 (1.5) 33 (1.30) 43 (1.69)
2702-350 Line 25 (1.0) n/a 36 (1.42) 46 (1.81)
2702-351 Line 76 (3.0) n/a 14 (0.55) 24 (0.94)
Table 2-3. Compatible Jaw Faces for 1kN, 2kN, 5kN and 10kN Grips
Catalog
No.
Surface Width -
mm (in)
Height -
mm (in)
Maximum Specimen Thickness
- mm (in)
2710-113 and
2710-114
2710-115 and
2710-116

Chapter: Specifications
2-6 M16-16348-EN
2702-352 Wave 51 (2.0) 51 (2.0) 22.5 (0.67) 32.5 (1.28)
2702-353 Wave 76 (3.0) 51 (2.0) n/a 5.0 (0.20)
2702-354 Vee-serrated 3 - 6.5
(0.12 -
0.25)
25 (1.0) 6.5 (0.25) 6.5 (0.25)
2702-355 Vee-serrated 6 - 18.5
(0.24 -
0.73)
25 (1.0) 18.5 (0.73) 18.5 (0.73)
Table 2-3. Compatible Jaw Faces for 1kN, 2kN, 5kN and 10kN Grips
Catalog
No.
Surface Width -
mm (in)
Height -
mm (in)
Maximum Specimen Thickness
- mm (in)
2710-113 and
2710-114
2710-115 and
2710-116
Table 2-4. Compatible Jaw Faces for 100N and 500N Grips
Catalog
No.
Surface Width - mm
(in)
Height - mm
(in)
Maximum Specimen
Thickness
- mm (in)
2702-360 Rubber 10 (0.4) 10 (0.4) 34 (1.34)
2702-361 Rubber 12 (0.5) 25 (1.0 34 (1.34)
2702-362 Rubber 25 (1.0) 25 (1.0 34 (1.34)
2702-363 Rubber 50 (2.0) 25 (1.0 34 (1.34)
2702-364 Rubber 100 (4.0) 25 (1.0 34 (1.34)
2702-365 Serrated 10 (0.4) 10 (0.4) 35 (1.38)
2702-366 Serrated 12 (0.5) 25 (1.0 35 (1.38)
2702-367 Serrated 25 (1.0 25 (1.0 35 (1.38)
2702-368 Serrated 50 (2.0) 25 (1.0 35 (1.38)
2702-369 Serrated 100 (4.0) 25 (1.0 35 (1.38)
2702-370 Smooth 10 (0.4) 10 (0.4) 35 (1.38)
2702-371 Smooth 12 (0.5) 25 (1.0 35 (1.38)

2-7
Grip Dimensions
Product Support: www.instron.com
2702-372 Smooth 25 (1.0 25 (1.0 35 (1.38)
2702-373 Smooth 50 (2.0) 25 (1.0 35 (1.38)
2702-374 Smooth 100 (4.0) 25 (1.0 35 (1.38)
2702-375 Brake Lining
(HFC)
25 (1.0 25 (1.0 34 (1.34)
2702-376 Brake Lining
(HFC)
50 (2.0) 25 (1.0 34 (1.34)
2702-377 Line Contact 25 (1.0 n/a 35 (1.38)
Table 2-4. Compatible Jaw Faces for 100N and 500N Grips
Catalog
No.
Surface Width - mm
(in)
Height - mm
(in)
Maximum Specimen
Thickness
- mm (in)

Chapter: Specifications
2-8 M16-16348-EN