Inta i-sport SP9206CP User manual

i-sport Shower Panel
SP9206CP & SP9207CP
Installation and Maintenance Instructions
In this procedure document we have endeavoured to make the
information as accurate as possible.
We cannot accept any responsibility should it be found that in
any respect the information is inaccurate or incomplete or
becomes so as a result of further developments or otherwise.
Intatec Ltd
Airfield Industrial Estate
Hixon
Staffordshire
ST18 0PF
Tel: [phone]
Fax: [phone]
email: sales@ ntatec.co.uk
web: www. ntatec.co.uk
© Intatec Ltd. 2014
www.divapor.com

© Intatec Ltd 2014 1
Introduct on
This installation guide has been produced for the SP9206CP i-sport compact shower panel.
These instructions cover the installation, operation and maintenance. Please read the enclosed
instructions before commencing the installation of this product, please note;
We recommend that the nstallat on of any Inta product s carr ed out
by an approved nstaller.
The installation must be carried out strictly in accordance with the Water Supply (Water Fitting)
Regulations 1999 and any local authority regulations.
If in doubt, we would recommend that you contact either your local water authority, the
secretary of the Water Regulations Committee at WRc on Tel: [phone] or Institute of
Plumbing on Tel: [phone].
All products MUST be re-commissioned to suit site conditions to ensure optimum performance
levels of the product are obtained.
Safety
43˚C is the maximum mixed water temperature from a shower mixer. The maximum
temperature takes account of the allowable tolerances inherent in thermostatic shower mixers
and temperature losses.
It s not a safe bath ng temperature for adults or ch ldren.
The British Burns Association recommends 37 to 37.5˚C as a comfortable washing
temperature for children. In premises covered by the Care Standard Act 2000, the maximum
mixed water outlet temperature is 43˚C.
Products
i-sport shower panel with timed flow shower and shower head -
top connection SP9206CP
i-sport shower panel with timed flow shower and shower head -
back connection SP9207CP
www.divapor.com

© Intatec Ltd 2014 2
Components
Item Qty Component Item Qty Component
1 1 Shower panel 618 l/min flow limiter
2 1 Shower head cover 71½” filter washer
3 6 Screws and wall plugs 81
3/8” fibre washer*
4 1 Self tapping screw 92Screw cap
5 1 ½” back entry leg* 10 1 Blanking cap*
* (SP9207CP only)
Check Content
Before commencing remove all components from packaging and check each component with
the contents list.
Ensure all parts are present, before discarding any packaging. If any parts are missing, do not
attempt to install your Inta compact shower panel until the missing parts have been obtained.
1
2
3
4
5
6
9
7
8
www.divapor.com

© Intatec Ltd 2014 3
Techn cal Data
This Inta i-sport compact shower panel is suitable for using recirculating hot water systems and
from a calorifier or hot water storage cylinder.
Water pressure range: 1 to 6 bar
Recommended water pressure range: 2 to 4 bar
Water temperature range: 5 to 65˚C
Water flow time: 30s +5/-10 seconds
Flow rate with flow regulator fitted: 8 l/m
Inlet Connections: G½B
General Recommendat ons
• Do not expose the shower to temperatures lower than 5°C (for example during winter time):
otherwise drain the system and any water residue.
• Adequate provision must be made to ensure the water quality (including limescale) when
installing the shower; the presence of impurities may damage the self-closing cartridge.
• If the system has not been used for a prolonged period, purge the up-streaming water supply,
before operating the shower.
• A service valve and check valve should be installed in the water supply pipework, should
maintenance be required in the future.
• For premixed water a thermostatic mixing valve should be fitted, preferably TMV3 such as an
Intamix with MX ends which include a ball isolating valve, strainer and single check valve.
• The flow time depends directly on the water pressure: the declared flow time refers to a 3 bar
dynamic pressure, according to European norm.
www.divapor.com

© Intatec Ltd 2014 4
Installat on
The whole system should be thoroughly flushed, prior to the connection of the water supply to the
shower or thermostatic mixing valve, to remove any debris that may be in the supply pipework.
The i-sport compact panel shower should be positioned at a convenient height for most users as
illustrated below.
2100
2246 External Water Supply
2215 Concealed Water Supply 31
55.5
www.divapor.com

© Intatec Ltd 2014 5
3
3
6
7
External Supply
• The shower panel is supplied for an external
water supply from above.
• Remove the shower head cover (2) from the
shower panel.
• Using the 6 fixing holes in the shower panel
as a template mark their positions on the wall
or use to drill pilot holes.
• Ensure the shower panel will be vertical when
fitted.
• Drill six holes and using the wall plugs and
screws (3) provided secure the shower
panel to the wall.
• Connect the water supply to the top
connection ensuring that the 8 l/m flow
limiter (6) and filter washer (7) are fitted.
www.divapor.com

© Intatec Ltd 2014 6
3
3
10
5
6
7
G B
Installer to apply
suitable Loctite thread
sealant - 2 drops
8
9
Concealed Supply
www.divapor.com

© Intatec Ltd 2014 7
Concealed Supply Cont.
The shower panel can be supplied by a concealed supply, through a wall or panel.
• Fit the blanking cap (10) to the top external supply connection.
• The concealed supply must terminate with a G½ parallel female thread.
• Insert the 8 l/m flow limiter (6) in the back entry leg (5) respecting the installation direction.
• Installer to apply 2 drops of a suitable Loctite thread sealant onto the smaller male thread,
which will lock the component in place.
• Fit the back entry leg (5), using a suitably sized spanner located on the two flats, onto
the concealed supply fitting using the fibre washer (8).
• Remove the shower head cover (2) from the shower panel.
• Carefully couple the shower panel onto the inlet connection fitting (5) and mark out precisely
the six fixing positions on the wall, ensuring the shower panel is vertical.
• Remove the shower panel and drill the wall and fit the 6 wall plugs.
• Permanently connect the supply to the shower using the filter washer (7).
• Using the screws (3) provided secure the shower panel to the wall.
www.divapor.com

© Intatec Ltd 2014 8
Complet ng the Installat on
• Fit the shower head cover (2) to the panel
and secure it in position with the self-taping
screw (4).
• Remove the screws caps (9) from the bottom
of the panel and fit them as shown.
2
4
9
www.divapor.com

© Intatec Ltd 2014 9
Operat ng the Shower
• Push the operating button (A), a small quantity of water
will be discharged through an outlet in the lower part of
the panel (C).
THIS WATER DISCHARGE IS NECESSARY FOR THE
CONTINUING OPERATION OF THE SELF CLOSING
VALVE (B), FOR THIS REASON THE OUTLET HOLE
MUST BE KEPT UNRESTRICTED
• When the operating button is released, the water flow will
stop automatically after the pre-de ned time.
Note: After installation you may need to operate the shower
once to clear any air inside the mechanism. Following this
operation the flow time will be within the pre-de ned time.
C
A
B
www.divapor.com

© Intatec Ltd 2014 10
D mens ons
15
1000
146
777
G B
18
31
85
www.divapor.com

© Intatec Ltd 2014
Intatec Ltd
Airfield Industrial Estate
Hixon
Staffordshire
ST18 0PF
Tel: [phone]
Fax: [phone]
email: sales@ ntatec.co.uk
web: www. ntatec.co.uk
E & .E
24-06-14
To active your product warranty please visit
www. ntatec.co.uk
and click on Product Registration
Aftercare
Inta i-sport compact shower panel has a high quality finish and should be treated with care.
An occasional wipe with a mild washing-up liquid on a soft damp cloth followed by a
thorough rinsing is all that is required.
Do not use an abras ve or chem cal household cleaner as this may cause damage.
Timed showers normally do not need any maintenance of the mechanical components, but its
reliability is mainly influenced by the water quality and debris within the system.
Spares
A full range of spares are available for this product.
PLEASE NOTE: nly genuine spares should be used.
www.divapor.com