Inta IR2568 User manual

Intatec Ltd
Airfield Industrial Estate
Hixon
Staffordshire
ST18 0PF
Tel: [phone]
Fax: [phone]
email: [email protected]
web: www.intatec.co.uk
In this procedure document we have endeavoured to make the
information as accurate as possible.
We cannot accept any responsibility should it be found that
in any respect the information is inaccurate or incomplete or
becomes so as a result of further developments or otherwise.
© Intatec Ltd 2021
Concealed WC Cistern
with Infra Red Flush
IR2568
Installation and Maintenance Instructions

© Intatec Ltd 2021 1
Introduction
This installation guide has been produced for the IR2568 concealed WC with infra red flush.
These instructions cover the installation, operation and maintenance. Please read the
enclosed instructions before commencing the installation of this product, please note;
We recommend that the installation of any product is carried out by
an approved installer.
The installation must be carried out strictly in accordance with the Water Supply (Water Fitting)
Regulations 1999 and any local authority regulations.
If in doubt we recommend that you contact WRAS - Water Regulations Advisory Scheme on
Tel: [phone], your local water authority - details available on the WRAS website or
the Chartered Institute of Plumbing and Heating Engineers on Tel: [phone].
All products MUST be re-commissioned to suit site conditions to ensure optimum performance
levels of the product are obtained.
It is recommended, especially in hard water areas, that a water softener such as the ActivFlo or
ActivFlo lite be fitted to reduce the risk of calcium deposits forming.
Products
Concealed WC with Infra Red Flush, Battery Operated IR2568
Check Content
Before commencing remove all components from packaging and check each component with
the contents list.
Ensure all parts are present, before discarding any packaging. If any parts are missing, do not
attempt to install your Inta thermostatic tap until the missing parts have been obtained.
Components
Item Component
1 Cistern with cover
2 Flush valve - installed in cistern
3 Inlet flow valve - installed in cistern
4 Solenoid valve
5 Infra red sensor
6 IP65 battery and battery box
7 Cable
8 Perspex tube
9 Flush pipe
10 Wall bracket, plastic plug and screw - 2 off

© Intatec Ltd 2021 2
Dimensions
Technical Specification
Operating water pressure range: 1 to 8 bar (recommended 5 bar maximum)
Power supply: 6V lithium battery - CRP-2
Flush volume: 6 litres
Auto-flush: every 24 hours from last flush
Operating
The water flush is activated by a hand wave 5 to 6 cm away from the infra red sensor.
Ø50
130
440
400
350
185
300

© Intatec Ltd 2021 3
Installation
Before commencing the installation ensure the wall on which the cistern is to be mounted is
structurally suitable.
Drill two holes in the wall above the toilet pan approximately at 300mm centres.
Using the plastic wall plugs and screws provided fix the two brackets to the wall.
Hang the cistern onto the two brackets directly above the toilet pan and using the flush pipe
connect to the toilet.
Connect the water supply to the cistern, a service valve must be installed in the supply pipe
should future maintenance be required.
Do not turn on the water supply at this time.
Drill a hole in the concealing panel 40 to 45mm in diameter in a convenient position above the
cistern for the infra red sensor.
The cable to connect the sensor to the solenoid valve is 1.2 m in length.
The perspex tube (8) is supplied connected to the flush valve inside of the cistern and is long
enough to protrude from the cover as shown.
The cover may need to be removed from the cistern to locate the perspex tube and position it
protruding through the hole.
Push the perspex tube onto the solenoid valve (4), ensuring that it is pushed fully home as a
loose connection can cause the toilet to work intermittently.
Ø55
Ø40-45
Max 65
Battery
Box
8
4

© Intatec Ltd 2021 4
Installation Continued
Finally position the valve into the hole in the cover.
Ensure the sensor cannot be affected by any external sources such as a mirror which may
create nuisance operation of the product.
The battery box is attached to the retaining bracket for the sensor as shown.
Using the cables provided connect the battery to the sensor and sensor to the solenoid valve.
Turn on the water supply and check for signs of leakage, allow the cistern to fill and check the
sensor for correct operation.
Failure to observe these installation instructions will invalidate the product
warranty.
Maintenance
Cleaning the Sensor
The darkened window which protects the sensor must always be clean in order to allow its
correct operation.
Do not use abrasive material to avoid damaging the plastic surface.
Battery Replacement
When the battery is exhausted, the LED flashes continuously and the solenoid valve stops in the
closing position.
Turn off the water supply to the cistern.
Pull apart the two halves of the connector to disconnect the battery
Remove the exhausted battery and replace it with a new one of the same type (CRP-2).
Dispose of the exhausted battery in an appropriate manner.
Batter
y
Box
56

© Intatec Ltd 2021 12
Warranty
The cistern and flush are covered by a 1 year warranty for any fault due to defects in material,
design or workmanship.
The warranty does not cover damage caused by: incorrect installation, negligence in
maintenance and use, acts of vandalism, contact with abrasive or corrosive chemicals and
unsuitable cleaning instruments.
Also the presence of any dissolved compound in the water (limestone, halogen compounds,
acids, etc.) leads to a loss of the warranty.

© Intatec Ltd 2021 13
Notes

Intatec Ltd
Airfield Industrial Estate
Hixon
Staffordshire
ST18 0PF
Tel: [phone]
Fax: [phone]
email: [email protected]
web: www.intatec.co.uk
E & O.E
© Intatec Ltd 2021 20-07-21
Please leave this Manual for the User
To activate your product warranty please visit
www.intatec.co.uk
and click on Product Registration