Integra BCR-S Mini G2 User manual

1-981-2181-GB, 2021-03-16 BCR-S Mini G2 Page 1
SystemHouse Solutions
Access Control –
and Security Management System
Installation manual
BCR-S Mini G2

1-981-2181-GB, 2021-03-16 BCR-S Mini G2 Page 2
SystemHouse Solutions
This document is Copyrighted ©2019 by SystemHouse Solutions AB. All rights reserved.
It may not be reproduced, modified, displayed transferred or copied in any form, in any matter or on any
media, in whole or in part, without the express written permission of SystemHouse Solutions AB.
SystemHouse Solutions AB reserves the right to make changes to this document and to the product
(software and hardware) described herein without notice.
SystemHouse Solutions AB assumes no responsibility for or liability for errors contained in this guide or for
incidental, special or consequential damages arising out of the use of this guide in operating the system.
All product names and trademarks mentioned in this document belong to their respective owners.

1-981-2181-GB, 2021-03-16 Contents Page: 3
SystemHouse Solutions
Table of contents:
1SYSTEM OVERVIEW ................................................................................ 4
1.1 PARTS LIST ........................................................................................................4
1.2 TECHNICAL SPECIFICATIONS.................................................................................4
1.3 ARTICLE NUMBERS..............................................................................................5
1.3.1 Accessories......................................................................................................................... 5
2SAFETY INSTRUCTIONS .......................................................................... 6
3INSTALLATION PROCEDURE .................................................................. 7
3.1 DEVICE OVERVIEW ..............................................................................................8
3.2 OPENING DEVICE ................................................................................................9
3.3 MAXIMUM TORQUE FOR BOX INSTALLATION ...........................................................9
3.4 INSTALLATION ON METAL SURFACES .................................................................... 10
3.5 WALL TAMPER.................................................................................................. 10
4POWER SUPPLY...................................................................................... 11
4.1 POWER REQUIREMENTS ......................................................................................11
4.1.1 Power supply.................................................................................................................... 11
5COMMUNICATION AND ADDRESS .........................................................12
5.1 SETTING ADDRESS............................................................................................. 12
5.1.1 Address setting on reader ...............................................................................................12
5.2RS485 COMMUNICATION LINE............................................................................ 14
5.2.1 Line installation ...............................................................................................................15
5.2.2 Line termination ..............................................................................................................16
5.2.3 Recommended cable ........................................................................................................16
5.2.3.1 PTS-HF-2x2x0.6......................................................................................................................... 17
5.2.4 RS485 network topology and termination principles ..................................................17
6SERVICE ROUTINES .............................................................................. 18
6.1 PERIODICAL SERVICE CHECK .............................................................................. 18
6.2 FIXING COMMON ISSUES WITH THE READER ......................................................... 19
6.2.1 No communication with the Reader...............................................................................19
6.2.2 Reader is not working .....................................................................................................19
7ATTACHMENTS...................................................................................... 20
7.1 CONSTRUCTION ............................................................................................... 20
7.2 FUNCTIONS ..................................................................................................... 20
7.3 BCR-S MINI G2 AS A PART OF DOOR ENVIRONMENT .............................................. 21
7.4 DRAWINGS.......................................................................................................22
7.4.1 Dimensions ...................................................................................................................... 22
7.5 HISTORY..........................................................................................................23

1-981-2181-GB, 2021-03-16 BCR-S Mini G2 Page: 4
SystemHouse Solutions
1 System Overview
This manual provides instructions for installation, cabling, power supply evaluation for BCR-S Mini
G2.
1.1 Parts List
Supplied:
I. BCR-S Mini G2 1 pcs
II. Connector 1 pcs
III. Wall tamper spring 1 pcs
IV. Quick Installation Guide` 1 pcs
V. Drilling pattern 1 pcs
VI. Opening Tool xCR-SD/S-Mini G2 1 pcs
Not supplied
I. Instructions for other devices that will be connected to the BCR-S Mini G2.
1.2 Technical specifications
Power supply Typical/Min/Max 24V DC/20VDC/30VDC
Power consumption Typical/Max at 24V 20 mA/25 mA
Enclosure IP 65
Operating temperature -25oto +70oC
Dimensions NET (L/W/H) 76.5/45/20 mm
Weight NET 46 g
Color NCS 8500-N
NCS 6502-B
Communication RS485

1-981-2181-GB, 2021-03-16 BCR-S Mini G2 Page: 5
SystemHouse Solutions
1.3 Article numbers
44 28 03 55 BCR-S Mini G2
1.3.1 Accessories
There are several accessories types available:
44 28 02 80 Installation plate for xCR-S (Mini) G2
44 28 02 75 Opening Tool xCR-SD/S (Mini) G2
44 28 50 21 Flashcable for xCR G2

1-981-2181-GB, 2021-03-16 BCR-S Mini G2 Page: 6
SystemHouse Solutions
2 Safety Instructions
The following safety instructions should observed during installation, maintenance and standard
use.
•Installation and service should only be performed by qualified personnel.
•If there exist local regulations, these must be followed. This safety information is
supplement to local regulations.
•Reader must be disconnected from voltage before installation and service.
•Do not modify any components or part of device.
•All reparation should be performed only by the manufacturer.

1-981-2181-GB, 2021-03-16 BCR-S Mini G2 Page: 7
SystemHouse Solutions
3 Installation Procedure
Installation procedure consist of evaluation of power requirements, mounting accessories, power
and communication lines wiring to S-Node G2, C-Node G2, Moveo, Moveo XL mounting,
connecting cables, setting switches and verification.
Set the device address according requirements. Default address is “2”. For setting
follow procedure in the section 5.2 Setting Address
When mounting outside, make sure no water can leak in through cable holes.
Evaluate power requirements as described in section 4 Power Supply.Same time evaluate
required power cables determined by required power and length of the cables.
Select cables used for communication lines as described in section 5 RS485 Communication
Line
Determine an appropriate mounting position for the device. The BCR-S Mini G2 is supported
to be installed on walls, mounting column, mounting brackets. The back plate of the unit
contain rubber sealing so it SHALL BE NOT used as a template for drilling. Use attached
drilling pattern instead.
Route the interface cables to S-Node G2, C-Node G2, Moveo, Moveo XL or to the other reader if
the actual reader is in the middle of the bus. Route cables to other accessories to be connected.
Install the bottom part of BCR-S Mini G2 box to the wall. Feed all cables inside the box to
appropriate position and fix them to the box with cable ties.
Connect all cables to the terminals as required.
Set termination jumper SW1 to enabled (default setting) if the actual reader is placed at the end
of the bus.
After wiring the BCR-S Mini G2 and accessories, device is ready to be tested. If the card reader
have been properly installed, connect terminal PL1 to the BCR-S Mini G2. The card reader will
beep for 1 second and starts working after short while (this is valid only in case that system was
already configured at PC level and that the parent node is up and running). This indicates that
unit is working properly.
Assemble the unit by pressing the top part down on the back plate. Ensure correct positioning
in the top before it is pressed into place.

1-981-2181-GB, 2021-03-16 BCR-S Mini G2 Page: 8
SystemHouse Solutions
3.1 Device overview

1-981-2181-GB, 2021-03-16 BCR-S Mini G2 Page: 9
SystemHouse Solutions
3.2 Opening device
To open device always use proper opening tool. Using other tools can cause scratches and damages
of the box that will cause warranty refusal.
For opening device follow instructions in Quick Installation Guide (part of device delivery) or look
in section Quick installation guide in this document.
Opening tool:
3.3 Maximum torque for box installation
When device is installed by using an electrical screwdriver the maximum torque used shall be 2.5
N/m.

1-981-2181-GB, 2021-03-16 BCR-S Mini G2 Page: 10
SystemHouse Solutions
3.4 Installation on metal surfaces
When device is installed on metal surface is strongly recommended to use proper accessory
44280280 Installation plate for xCR-S (Mini) G2.
This will minimize problems with low reading distance caused by interfering with metal surface.
3.5 Wall tamper
In case when is required to use also wall tamper for higher security grades where it is necessary to
install wall tamper springs.
Installation procedure:
1. Open device using opening tool.
2. Cut tamper activators placed at bottom cover at plastic level.
3. Install springs from bottom side.
4. Fix bottom cover with screws at installation place. Surface level needs to be even.