Integral LED ILBTE059 User manual

Thank you for purchasing an INTEGRAL LED product. When installed correctly this unit will provide years of service – with no
lamp changes required. For support or warranty information please see integral-led.com. Always turn o circuit power at the
distribution unit before installation and maintenance. Please ensure that the power cannot be connected inadvertently.
Important Details – Please read prior to installation
Ensure the AC/Mains power is NOT connected and cannot be unexpectedly reconnected during installation.
1. This product must be installed by a competent qualied electrician in accordance with the instructions provided and in compliance with
recognised electrical and safety regulations relevant to the country in which it is being installed.
2. This product is suitable for installation on surfaces with normal ammability e.g. wood, masonry. Before making the xing hole(s),
check that there are no obstructions hidden beneath the mounting surface, such as pipes or cables. It is not suitable for use on highly
ammable surfaces or in a ammable atmosphere.
3. For ceiling, wall mounted or suspended installations please follow “Installation instructions” below. For surface mount, this product
must be securely xed to the mounting surface using the brackets, screws and wall plugs supplied (Fig. 1). The screws and wall plugs are
suitable for “masonry” only.
IMPORTANT! This product is a Class II device and requires no earth connection.
Installation Instructions
1. The unit is pre-wired with cable at the rear of the product to connect to incoming mains cable. The length of pre-wired cable equals
half the batten length plus 10cm.
2. Connect the mains supply cable to the pre-wired cable of the batten using suitable connectors. Only LIVE (brown) and NEUTRAL (blue)
are required.
Surface mount installation (Fig. 2 - 5)
1. These can be ceiling and wall mounted.
2. Secure the supplied brackets to the surface as shown in the diagram and press the batten carefully onto the brackets.
3. For secure sensor operation the product should be ceiling mounted. Fix the brackets using the xing supplied or alternative suitable
xings to secure the bracket in place. Please ensure brackets are in line and xed perpendicular to the desired position for the central
longitudinal axis of the product. Ensure the brackets are in line and at a spacing within the overall length of the product to be installed.
Place a minimum distance of 400mm apart.
Suspended installation
Requires suspension mount kit ILBTASK065 which can be ordered separately.
INSTALLATION INSTRUCTION
for Integral Value+ LED battens
3 Year Warranty
EN
Product code Function Product Dimensions (mm) (LxWxH) Net weight (Kg)
ILBTE059 2ft 20W 3000K LED Batten 667 x 54 x 42mm 0.19
ILBTE060 4ft 40W 3000K LED Batten 1187 x 54 x 42mm 0.37
ILBTE061 5ft 60W 3000K LED Batten 1500 x 54 x 42mm 0.46
ILBTE062 2ft 20W 4000K LED Batten 667 x 54 x 42mm 0.19
ILBTE063 4ft 40W 4000K LED Batten 1187 x 54 x 42mm 0.37
ILBTE064 5ft 60W 4000K LED Batten 1500 x 54 x 42mm 0.46
ILBTASK065 suspension kit 2 wires 1.5M

ON
OFF
ON
OFF
160mm 160mm
Warranty
This unit carries a 3 year warranty from the date of purchase, providing that it has been installed correctly and not modied in any way.
Should a fault occur please contact the original place of purchase.
Important Notes
• Operating and luminaire must be within rated temperature -10 to +40°C avoiding extreme humidity
• Operation must be within rated input voltage.
• Keep away from strong electromagnetic radiation sources and protect from lightning strike.
• Should the unit malfunction, return to distributor or reseller. No user serviceable parts inside. Do not disassemble or attempt to repair
the luminaire outside of the installation guidelines.
• Do not install or use the luminaire if the housing/diuser is found to be broken.
• Do not apply direct pressure to the diuser.
• The luminaire must be installed by a qualied electrician.
• The luminaire should be positioned away from heat, vibration and liquid. Avoid contact with any corrosive chemicals.
• The luminaire should be positioned to allow normal convectional cooling within free owing air and an ambient temperature
not exceeding 30°C.
• Never cover the luminaire with heat insulation materials.
• The luminaire should be positioned at least 1 metre away from radios, failure to do so may aect radio reception.
• No user-replaceable parts.
• For indoor use only.
Installation diagrams
Fig.1 Fig.2
Fixing accessories
in the box
Mains wiring:
Live - Brown
Neutral - Blue
Warranty/Technical and contact information
are all available at www.integral-led.com
Integral LED is a division of Integral Memory plc:
Unit 6, Iron Bridge Close, Iron Bridge Business Park,
London, NW10 0UF, UK
Non-Dimmable
IP20
Fig.3 Fig.4
WASTE ELECTRICAL PRODUCTS SHOULD NOT BE
DISPOSED OF WITH HOUSEHOLD WASTE. PLEASE
RECYCLE WHERE FACILITIES EXIST. CHECK WITH
YOUR LOCAL AUTHORITY FOR RECYCLING ADVICE.