Intel ZA-SK1050 2L4C User manual

Support Intel 6th/7th Corei7/Corei5/Corei3 Processor
®
ZA-SK1050 2L4C Motherboard
User Manual

ZA-SK1050 2L4C Motherboard Configuration Diagram

ZA-SK1050 2L4C Motherboard Diagram

235mm x 197.5mm
Size
CPU
Graphics
Chipset
Memory
Internal I/O
Rear I/O
BIOS AMI
MINI_PCIE
LAN
Audio
Operating System
H/W Monitoring
SATA
Humidity
Temp
NVIDIA GTX1050Ti
B150
2*DDR4 2133MHZ,Up to 32GB
4*USB2.0 Pin 7*USB Port
1* CPU Fan And GPU Fan
1*SYS Fan
2*LVDS Pin(support dual Channel 10 Bit)
4*SATA
4*COM
1*Front panel Pin
1*Audio Pin Port (2W/CH)
1* DC Power Input (19V)
1*HDMI
1*LAN
2*SATA
2*JSATA
4*USB3.0
1* Mic-in/Line-out
1*Support Msata
1*Support WiFi
4*SATA
2*Realtek 8111E,10/100/1000
ALC662 Dual Channel Output
Windows7
Windows8
Windows10
Linux
Walk in LAN
System Power Management
Temperature Management
Voltage Management
0% ~ 95% (Relative Humidity,No Condensation)
-10°C ~ 55°C
Support Intel 6th/7th Core i7 i5 i3 Processor
AMIBIOS,64M bit Flash Memory
R
Motherboard Specification

Motherboard I/O Interface Diagram
CMOS_BT1 19VDC HDMI TJ1 TJ4 USB3.0 USB3.0 Mic/Lineout
FUSB1 INVTER1 LVDS2
COM1-4 DP1 LVDS1 SATAIII_2
JSATA1-2
CN1
SYS_FAN1
VGA_FAN2 CPU_FAN
FP1SPK1
FUSB4
FUSB2
M2WIFI
FUSB3
M2SATA
SODIMM2
SODIMM1

CPU_FUN
GPU_FAN2
SYS_FAN1
DDR4
Installation memory:
1. Please turn off the power before installing or removing the
memory, and dial down the AC power cord.
2. Carefully hold both ends of the memory stick, and do not touch
the metal contact above.
3. Align the gold fingers of the memory stick with the memory stick
slot, and pay attention to the convex point of the gold finger socket
to the upper slot in the direction;
4. Insert the memory stick 30 degrees into the memory slot, and
then press the memory stick down to the sound of "click"
The memory has been installed successfully and can be used
(note: press down the memory bar to avoid damaging the memory
too much)
Note: these fan connectors are not jumpers, and the jumper cap is placed above the head.
LVDS2
Memory installation diagram (for reference only) :
Note: static electricity damages electronic components of a computer or memory,
so before following these steps,Be sure to touch the grounded metal objects briefly
to remove static electricity from your body.
接脚 接脚定义 接脚 接脚定义
1LCDVDD 2 LCDVDD
3LCDVDD 4GND
5GND 6GND
7LVDSA_DATA0N 8 LVDSA_DATA0P
9LVDSA_DATA1N 10 LVDSA_DATA1P
11 LVDSA_DATA2N 12 LVDSA_DATA2P
13 GND 14 GND
15 LVDSA_CLKN 16 LVDSA_CLKP
17 LVDSA_DATA3N 18 LVDSA_DATA3P
19 LVDSB_TX0N 20 LVDSB_TX0P
21 LVDSB_TX1N 22 LVDSB_TX1P
23 LVDSB_TX2N 24 LVDSB_TX2P
25 GND 26 GND
27 LVDSB_CLKN 28 LVDSB_CLKP
29 LVDSB_TX3N 30 LVDSB_TX3P
(LVDS显示屏电路板供电选项)
1 2 3 1 2 3
或
PIN 1-2 Close: PIN 2-3 Close:
3V 5V

INVERT
Pin Define Pin Define
1
12V
2
12V
3 ON/OFF 4 ADJ
5
GND
6
GND
JSATA2
JSATA3
LPC
SPK1
SATAIII_1
SATAIII_2
+5V 2. GND 3.GND 4.+12V
Note: this port belongs to the debugging port of the main board and cannot be used for other ports.
Pin Define
Pin
Define
1
3
2
4SPKOUT_R+SPKOUT_R-
SPKOUT_L+
SPKOUT_L-
FUSB1
FUSB2-4
F_USB1 F_USB2-4
12
34
56
78
910
VCC VCC
DATA 0- DATA1-
DATA1+
GND
GND
NC(CUT) GND
Pin Pin Pin
Define Define Define
1VCC
2 DATA 0-
3 DATA 0+
4 GND
DATA0+

Mic-in/Line-out
FP1
Pin Define Pin Define
1
3
5
7
9
2
4
6
8
HDD LED+ PWR LED+
HDD LED- GND
GND
RESET_GND
P_SWIN
GND
GND
*Other Matters Please consult the sales.
HDD Actiuve LED:1,3 Power Button:6,8
Power LED:2,4 Reset Button:5,7
ShenZhen Zeal-All Technology Co.,Ltd
www.zeal-all.com
[phone]