Intelligent Facility Solutions Dryflow Vapordri User manual

Dryflow® Vapordri Hand Dryer
INSTALLATION MANUAL

Pag.2 www.intelligenthanddryers.com
Dryow® Vapordri Hand Dryer
1. SAFETY INSTRUCTIONS
Please read carefully this manual before carrying out any
acon and do take into account all the safety instrucons
listed below:
- Only qualied technicians are entled to install, x and carry
out the maintenance of this device. Any acon carried out
on the device must respect the current legislaon and safety
regulaons, both local and European.
- Be especially careful when removing the cover of the hand
dryer, as some acve parts of the device will be exposed,
involving risk of electric shock. Turn o all power sources
before carrying out any electric handling, in order to avoid risk
of electric shock.
- The device must be installed out of reach of any water point,
respecng safety distances established by the current IEC
Regulaons.
INDEX
1. SAFETY INSTRUCTIONS ................................................................................................................... 2
2. INTRODUCTION .............................................................................................................................. 4
3. INSTALLATION ................................................................................................................................. 5
4. OPERATION ..................................................................................................................................... 8
4.1 Drying........................................................................................................................................ 8
4.2 Heang element ....................................................................................................................... 9
4.3 Water tank ................................................................................................................................ 9
5. MAINTENANCE ............................................................................................................................. 10
6. CLEANING OF WATER TANK .......................................................................................................... 12
7. CONEXION DIAGRAM.................................................................................................................... 13
8. TECHNICAL FEATURES................................................................................................................... 14
9. PACKAGE CONTENT....................................................................................................................... 15
10. ENVIRONMENTAL PROTECTION.................................................................................................... 15

www.intelligenthanddryers.com Pag.3
Dryow® Vapordri Hand Dryer
- Local rules and specicaons for installaon must also be
taken into account, as in some cases a safety distance greater
than 0.6 m could be required.
- It is necessary to ancipate procedures to cut the electric
circuit, with at least 3mm contact distance in all poles. Those
disconnecon procedures must be included into the network,
respecng the current European legislaon. Please ensure
that electric installaon has RCD of high sensivity ≤ 0.03A.
- The device can be used by children over 8, as well as by
people with reduced capacies (either physical, sensorial or
mental) and by people with lack of experience or knowledge
if they are supervised, or if they receive some training about
how to use the device in a safe way, and which are the risks
involved. Children must not play with the device; maintenance
cannot be carried out by children without supervision.
- Device must not be installed in ammable areas.
- The device cannot be xed to wall by means of adhesives
or similar means; this is forbidden by the European Security
Regulaons. You must use the xing support provided by the
manufacturer.

Pag.4 www.intelligenthanddryers.com
Dryow® Vapordri Hand Dryer
2. INTRODUCTION
The main features of the Dryow® Vapordri hand dryer are the following:
• Automac funconing. The hand dryer will automacally turn on when hands are detected by IR
sensors. Sensibility of these sensors can be regulated through the potenometers placed inside
the device.
• HEPA lter . The device is equipped with large HEPA lter which requires less frequent replacement
and facilitates aspiraon, which increases air ow. The lter is easy to access, clean and remove.
• Anbacterial ABS. The device is manufactured from ABS plasc which contains some addives
that avoid proliferaon of bacteria, fungi and mould.
• Water tank. Hand dryer has a wáter tank to recover wáter from hands during drying process. The
wáter tank must be empty and cleaned regularly.
• High performance and low consumpon. Heang element of the device turns o automacally
when room temperature is above 25º, saving energy.
• High performance. Drying me is only between 10 to 12 seconds, what makes it suitable for areas
with high trac of people.
• Alarms. Several alarms are included to warn about maintenance needs: water tank full, change of
HEPA lters, change of motor brushes.

www.intelligenthanddryers.com Pag.5
Dryow® Vapordri Hand Dryer
3. INSTALLATION
For correct installaon, please follow the next steps:
1- Remove back cover. Break die-cut opening, which is designed to pass power cord through and
screw it to connecon strip. Screw duct provided as a protecon to prevent cord to be pulled
accidentally.
NOTICE: Power cord is not supplied with the device, it must be installed by a qualied technician.
Cable MUST BE TYPE H05RN-F 2 x Ø 1.5mm.
Connecon strip for
power cord to network
230V 50Hz Restraint
system for
power cord
(an-pull
protecon)
POWER CORD H05RN-F
2 x Ø 1.5mm

Pag.6 www.intelligenthanddryers.com
Dryow® Vapordri Hand Dryer
2- Fix to wall by means of screws provided. It is essenal the device is properly aligned; it is therefore
advisable to use the bubble level included on the support xed to wall. Installaon height must be
as follows:
3- Connect the hand dryer to the power supply.
4- If when you are operang the hand dryer for the rst me, you noce that the sensors do not
detect hands properly, it will be necessary to calibrate sensors again. This can be done by removing
front cover. To disassemble front cover, remove two screws at the boom, and slide it vercally
upwards, where you will nd main switch of the device. The switch will be set in “ON posion”
when the device is delivered.
Screws for wall fixing. It is recommended to use
screws and wall plugs in all 5 fixing holes.
* Z shows required distance from floor to
the centre of hole of the metallic support to
fix hand dryer to wall.
RECOMMENDED MOUNTING HEIGHT
OF HAND DRYER
Z = 90 cm Z = 85 cm
1 meter
Z
Slide cover
upwards to
remove it
Screws to fix
front cover
Screws to fix
front cover
OFF
ON

www.intelligenthanddryers.com Pag.7
Dryow® Vapordri Hand Dryer
In order to recalibrate sensors you will need to manipulate potenometers. Do it carefully as they are
highly sensive electronical components. Turn potenometers with a at head screwdriver clockwise
or counterclockwise, whichever applies.
IR SENSORS REGULATION:
Electronical plate
with potenometers
to calibrate hand
detecon sensors
Right
Sensor
Le
Sensor
P1 (Right sensor):
(+) sensivity: turn clockwise
(-) sensivity: turn
counterclockwise
P2 (Le sensor):
(+) sensivity: turn
counterclockwise
(-) sensivity: turn clockwise

Pag.8 www.intelligenthanddryers.com
Dryow® Vapordri Hand Dryer
4. OPERATION
4.1 Drying
To switch the hand dryer on it must be connected to the power supply and the internal illuminated
switch must be ON.
NOTICE: When the device is delivered the internal switch is ON, so it is not necessary to remove the
front cover to acvate it.
When hand dryer is switched on, it automacally carries out an internal check; aer some seconds it
will be ready to use.
The right way to use the hand dryer is by introducing vercally both hands, separated, so that they
can be correctly detected by IR sensors.
When motor starts, countdown will be shown on the display of the device, which is similar to a
barcode. The opmal drying me would be one cycle of the barcode display. However if the user
wishes to connue with the drying, another cycle will start automacally without being necessary to
remove hands and introduce them again. Maximum drying me is 30 seconds.
Hand dryer automacally switches o when removing hands.
1234
If blinking means
problems with IR and / or end of cycle
30 seconds
Alarms
Duraon of drying cycle

www.intelligenthanddryers.com Pag.9
Dryow® Vapordri Hand Dryer
4.2 Heang element
Heang element acvates when room temperature is lower than 25ºC. When the device is in use,
LED diuser light will be red if heang element is acve and blue if heang element is o.
4.3 Water tank
The hand dryer will collect the water that is released from the hands during drying. The water will
be taken to a small water tank located at the boom of the hand dryer. The water tank is accessible
from the boom of the hand dryer. It has a latch for release and removal for emptying and cleaning.
4.3.1 Flooding due to misuse or breakdown of the device
For safety reasons, if ooding occurs, due to misuse of breakdown, wáter tank has been designed to
throw out the wáter outside the hand dryer without damaging it.
LED diffuser light:
RED: Heang element on
BLUE: Heang element off

Pag.10 www.intelligenthanddryers.com
Dryow® Vapordri Hand Dryer
5. MAINTENANCE
• Water tank full ( ). When the logo is ON it means that the wáter tank is almost full and must be
empty and cleaned. In order to do it, please follow instrucons from point 6 CLEANING OF WATER
TANK.
• HEPA lter (1). It acvates when sucon is blocked or when HEPA lter is saturated. Hand dryer
will stop funconing; lter must be replaced.
To do so, remove lter cover, situated at the boom of the device. It is xed by means of two
screws, which can be unscrewed by inserng a coin or a athead screwdriver into the slot and
rotang 90⁰. Cover will come o and then lter can be removed easily.
• Motor brushes (3). Nocaon of wear of motor brushes, they need to be replaced. Aer
replacement of brushes, please reset the motor counter following instrucons included further in
this secon.
• Intelligent Facility Soluons logo (blinking). It means that 30 seconds programmed drying cycle is
nished. If sensors detect a stac object for longer than 30 seconds, the device will automacally
stop.
• Heang element. If the device does not expel hot air when the LED diuser light is red, then
there is a breakdown on the heang element. Wait for some minutes unl device cools o. If the
problem persists, please contact Technical Support.
• Cleaning. Keep drain clean. Clean only with damp cloth. Do not use acid or bleach. Clean display
of IR sensors regularly.
Fixing screws



www.intelligenthanddryers.com Pag.11
Dryow® Vapordri Hand Dryer
Note: The buon situated on the cover of the electronic is used to reset the motor operang hours
counter, and therefore, it shows when the brushes have been changed.
To reset counter, press the buon and at the same me, turn on the device by means of the illuminated
pushbuon. Please keep it pressed unl the rst bar illuminates. Once the pushbuon is released,
the counter is reset to zero and all the bars light up connuously.
Buon to reset
motor counter

Pag.12 www.intelligenthanddryers.com
Dryow® Vapordri Hand Dryer
6. CLEANING OF WATER TANK
Pull out water tank. Remove cover.
Empty water
and clean water tank.
Insert cover again
and insert water tank
in hand dryer again.
When triangle symbol shines, water
tank is almost full. Please empty
water tank following below
instructions.
The tank is located at the bottom of
the hand dryer.
1 2 3
4 5 6
Release tank
by turning lock.
Aach water tank
by turning lock.

www.intelligenthanddryers.com Pag.13
Dryow® Vapordri Hand Dryer
7. CONEXION DIAGRAM
Circuits:
PW. Power circuit
CN. Control circuit
LED. Leds air nozzles
IR. IR sensors circuits
DS. Display
PT. Pressure temperature sensor
Pushbuom. Boton reset for motor counter
Main switch.
AC Input. Terminal block
Blower Motor. Motor 1 kW 230 V 50 Hz
Air heater

Pag.14 www.intelligenthanddryers.com
Dryow® Vapordri Hand Dryer
8. TECHNICAL FEATURES
Voltage 230V~50Hz Motor type Universal
Total power 1550 W Insulaon class Clase II
Motor power 1050 W Protecon class IP21
Power heang resistance 500 W Dimensions 320 x 540 x 180
cm
Weight 6,830 kg
Technical features sheet:
Symbols used in the characteriscs sheet of the device:
IP Codicaon system to indicate protecon levels provided by an enclosure to
prevent access to dangerous parts, penetraon of foreign bodies, penetraon
of water and to add further informaon to protecon reference.
VVoltage
AC Alternang current
Hz Frecuency in Hertz
WPower in Wats
Electrical insulaon CLASS II: Grounding wire not required
CE – European Community Marking
RoHS & WEEE European Direcve on waste electrical and electronic
equipment
IP 21 SERIAL NUMBER
Model: DFVAP1G
Voltage: 230V AC 50Hz
Power: 1000-1550W
CLASS II
C/La Rioja 3, 03006
Alicante (Spain)
www.intelligenthanddryers.com

www.intelligenthanddryers.com Pag.15
Dryow® Vapordri Hand Dryer
9. PACKAGE CONTENT
• Dryow® Vapordri Hand Dryer.
• Wall support with bubble level.
• Screws to x support and device to wall.
• Warranty document.
• Installaon manual.
10. ENVIRONMENTAL PROTECTION
In compliance with RoHS direcve “Direcve 2002/95/EC” about electrical and electronic equipment,
this electrical hand dryer does not contain any lead, nor mercury, cadmium, hexavalent chromium,
prolybrominated biphenyl (PBB) or Polybrominated diphenyl ethers (PBDE) or Phthalates.
This symbol of a crossed out wheelie bin can be found on the characteriscs sheet
of the hand dryer. It means that at the end of the life of the device it must not be
disposed of with the household waste. To facilitate recycling and avoid negave
consequences for the environment and health, the product can be disposed in
specic collecon facilies for electrical and electronic equipment, that have been
designed by local administraons to deal with this type of waste in each town.

INTELLIGENT FACILITY SOLUTIONS LTD.
Electric House, 51 Wisewood Road
Shefeld, S6 4TB, United Kingdom
Phone UK: [phone]
Phone Eire: [phone]
[email protected]
https://www.intelligenthanddryers.com/