Intelligent Home DT-DJ4A User manual

Audio Phone
2
User Manual
iRead this manual carefully before using the product, and keep it well for future use.
DT-DJ4A

2
33
Side View
187
150
97
Handset
Call button/Unlock 2nd button
Speaker
handset curve
1. Parts and Functions
Unlock button
Call button/Unlock
2nd button
Speaker Send out voice from the visitor.
Key functions
In standby mode, pick up handset, press Call button to
activate the inner (internal intercom) call;
During calling/talking state, press Unlock 2nd button to
release the second door.
Handset Pick up to communicate with called.
Handset cable Connects handset with monitor. Unlock
Button Press to release the door.

L2 L1
SW+SW-
1 2 3 4 5 6
ON DIP
ON
1 2 3
K4
K3
K4
K3
DIP2
DIP1
L2 L1
SW+SW-
1 2 3 4 5 6
ON DIP
ON
1 2 3
K4
K3
SW+,SW-
L1, L2
2
2
2. Terminal Descriptions
SW+,SW-:Door bell call button connection port.
L1,L2: Bus terminal.
K4: Used to set Ring Tone.
K3: Used to set Ring Volume.
DIP1(Bit1~6): Used to set User Code.
DIP2(Bit1~3): Used to set Slave Monitor Address or Extended Address
3. Unit Mounting
1). Fix bracket using 2 screws to the wall at an appropriate height
2). Connect the system correctly
3). Attach the audio handset to the bracket.

Bit state User Code Bit state User Code Bit state User Code
1 2 3 4 5 6
ON
Code=1
1 2 3 4 5 6
ON
Code=12
1 2 3 4 5 6
ON
Code=23
1 2 3 4 5 6
ON
Code=2
1 2 3 4 5 6
ON
Code=13
1 2 3 4 5 6
ON
Code=24
1 2 3 4 5 6
ON
Code=3
1 2 3 4 5 6
ON
Code=14
1 2 3 4 5 6
ON
Code=25
1 2 3 4 5 6
ON
Code=4
1 2 3 4 5 6
ON
Code=15
1 2 3 4 5 6
ON
Code=26
1 2 3 4 5 6
ON
Code=5
1 2 3 4 5 6
ON
Code=16
1 2 3 4 5 6
ON
Code=27
4. Operation Instructions
1) Door release function: When visitor calls from outdoor station, the internal handset
rings, pick up handset to talk with the caller, then press the Unlock button to open the
door. If the system is connected to 2 locks, press Unlock 2nd button to open the second
door.
2) Inner call(Internal Intercom Call):Pick up handset, then press CALL button to
activate the inner call, all handsetsconnected to the system will ring at the same
time. Pick up any handset,the others will stop ringing immediately(note that the user
address must be the same for all handsets to activate the inner call function).
3) Door Bell Call Button: An additional door bell call button can be connected to the
handset so that the visitors can ring the door bell again in front of the user’s
apartment. When the call button is pressed, the handset will ring.
5. Setup Instructions
5.1 User Code Setting(DIP1 to set it)
• Bit-1~5 of DIP1 are used to set the User Code. The value is from 1 to 32,
allowing 32 different codes for 32 apartments.
2Easy requires every apartment to have a unique identification called User Code(address).
DIP1 switches are used to set the User Code for each handset.
• Bit-6 of DIP1 is used to set end of line.

Bit state User Code Bit state User Code Bit state User Code
1 2 3 4 5 6
ON
Code=6
1 2 3 4 5 6
ON
Code=17
1 2 3 4 5 6
ON
Code=28
1 2 3 4 5 6
ON
Code=7
1 2 3 4 5 6
ON
Code=18
1 2 3 4 5 6
ON
Code=29
1 2 3 4 5 6
ON
Code=8
1 2 3 4 5 6
ON
Code=19
1 2 3 4 5 6
ON
Code=30
1 2 3 4 5 6
ON
Code=9
1 2 3 4 5 6
ON
Code=20
1 2 3 4 5 6
ON
Code=31
1 2 3 4 5 6
ON
Code=10
1 2 3 4 5 6
ON
Code=21
1 2 3 4 5 6
ON
Code=32
1 2 3 4 5 6
ON
Code=11
1 2 3 4 5 6
ON
Code=22
DIP2 state Master/Slave type
1 2 3
ON
Master monitor
1 2 3
ON
Slave monitor 1
1 2 3
ON
Slave monitor 2
1 2 3
ON
Slave monitor 3
5.2 Slave Address Or Extended Address Setting(DIP2 to set it)
When multiple handsets are installed in one apartment, these handsets must use the
same User Code setting, the Master/Slave mode should be set on the handset.
• Bit-1~2 of DIP2 are used to set the slave address or extended address.
• Bit-3 of DIP2 is used to switch between Master/Slave and extended addressing.
• When Bit-3 of DIP2 is set to OFF, Bit 1 & 2 are used to set the Slave addressing

1 2 3 4 5 6
ON
Code=33
1 2 3
ON
DIP2 state DIP1 state User Code
1 2 3 4 5 6
ON
Code=1
1 2 3
ON
1 2 3 4 5 6
ON
Code=2
1 2 3
ON
.........
1 2 3 4 5 6
ON
Code=31
1 2 3
ON
1 2 3 4 5 6
ON
Code=32
1 2 3
ON
1 2 3 4 5 6
ON
Code=34
1 2 3
ON
.........
1 2 3 4 5 6
ON
Code=63
1 2 3
ON
1 2 3 4 5 6
ON
Code=64
1 2 3
ON
.........
.........
1 2 3 4 5 6
ON
Code=65
1 2 3
ON
1 2 3 4 5 6
ON
Code=66
1 2 3
ON
1 2 3 4 5 6
ON
Code=95
1 2 3
ON
1 2 3 4 5 6
ON
Code=96
1 2 3
ON
1 2 3 4 5 6
ON
Code=97
1 2 3
ON
1 2 3 4 5 6
ON
Code=98
1 2 3
ON
1 2 3
ON
1 2 3 4 5 6
ON
Code=127
1 2 3
ON
1 2 3 4 5 6
ON
Code=128
DIP2 state DIP1 state User Code
Group name Items Songs
Group1
Door Station DINGDONG
Intercom Call TELEPHONE_RING
Door Bell DINGDONG
Group2
Door Station JINGLE_DELL
Intercom Call CARMAN
Door Bell FOR_ALICE
Group3
Door Station HAPPY_BIRTHDAY
Intercom Call SONATINE
Door Bell CONGRATULATE
Group4
Door Station DOREME
Intercom Call RHYTHM_OF_THE
Door Bell EDELWEISS
5.2.2 When Bit-3 of DIP2 set to ON, the Bit-1~2 of DIP2 and Bit-1~5 of DIP1 are
used to extended address setting:
5.3 Ring Tone Setting
1). There are four groups ring tones to choose from:

The design and specications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved.
Low-range Mid-range High-range
press K3 press K3
press K3
3). Put down handset to exit the setting.
3). Put down handset to exit the setting.
5.4 Ring Volume Setting
2). Pick up the handset in standby mode, each press of K4 sets the next a group
of ring tones.
1)There are three levels of ring volume(low-range, mid-range and high-range). 2).
Pick up the handset in standby mode, each press of K3 sets the next ring volume.
Ring volume cycle:
Ring tone group cycle:
●Dimension:
●Power Consumption: Standby 2.1mA,working 75.9mA
●Wiring: 2 wires, non-polarity
187(H)X97(W)X33(D)mm
●Power Supply: 24VDC
6. Specification
press K4press K4 press K4
Group1 Group2 Group3 Group4.