IntelliSense IV 380X24A Installation manual

CCD Camera Products.
CCD Black
- and - white Camera
Models IV 380X24A ( CCIR)
IV 380424A ( EIA )
Operation Manual
Before operating the unit, Please read this manual thoroughly and retain it for future
reference.
The Lens in the picture is not included.
1

Features :
There are two mounting holes provided for flexible installation. One on the top
and the other one on the bottom.
Resolution:
This camera is using 1/3” CCDimage Sensor with an effective 252K (EIA)/298K
(CCIR) pixels. The camera can produce an image with a horizontal resolution of
380 TV lines.
Electronic Shutter:
This camera is equipped with automatic electronic shutter circuit. The shutter
speed will automatically adjust from 1/60
to l/10000 second for EIA and 1/50 to
l/10000 second for CCIR system.
Minimum Illuminance:
This camera has AGC (Auto Gain Control) circuit. As a result, the camera can
produce a clear image with a minimum illuminance of 0.1 Lux.
Auto IRIS Lens Control:
The Camera has provided control signal and miniature plug for both the Video or
Direct Drive Auto IRIS Lens.
Synehronzation:
Internal or external (line lock) synchronization is selectable.
Gamma Characteristic:
y = 0.45.
Input Power:
24V AC and the current consumption is less than 165mA.
Power On Indication Light
3

The camera comes with the following:
(a)
(b) 6 angle wrench.
(c) C mount adaptor.
(d) Operation Manual.
Miniature Plug for Auto Iris Lens
(a) Miniature Plug (b) 6 angle wrench (c) C Mount adaptor
Operation Procedure:
(a)
Install a CS mount type lens to the camera. If a C mount type lens is used, please
install the lens with the C mount adaptor (provided)to the camera.
Connect coaxial cable
from the camera video output to video input of Monitor or
other video equipments directly.
(In surveillance system combination, please be
sure that the input
of the last video equipment terminated at 75 Ohms.) The
picture will appear
on the monitor screen when the power is supplied to the
camera.
(b)
4

FUNDAMENTAL SYSTEM
f
MONITOR CAMERA
The Auto Shutter Control Switch is set to " ON " position at the factory before the
camera is shipped. With the Auto Shutter Control Switch is in the
" OFF "
position, adjust aperture of the lens to obtain the most desirable aperture setting.
Please adjust the focus on the lens to obtain the best quality picture on the
monitor. After performing the above process, if Auto Shutter is required, please
turns the switchto
" ON " position.
(d) Back Focus Adjustment: Depending on the lens used, proper focus may not be
obtained even by performing lens focus adjustment. In this case, back focus
adjustment is needed. First, set the focus ring of the lens to the infinite position
and take a picture at a distance of 20 meter or more from the camera. Loosen the
lens mount with the
6 angle wrench, and turn the mount and the lens at the same
time
so that the picture on the monitor is in focus. Then secure screw firmly at
the point where the subject is in focus.

BACK FOCUS SCREW ADJUSTING
r
The external synchronization (Line Lock) switch is set to “ON” position at rhe
factory, The camera will synchronize to the zero crossing of incoming AC
voltage, which is connected
to the middle pin of the power connector. Please
ensure that all the input AC voltage connection of the camera are on the same
phase. If the power voltage connection is reversed. the camera will lock at
180^
of the incoming AC voltage. When the wrong connection is found, please make
the correction
for the zero crossing synchornization purpose.
How To Use Auto Iris Lens
(a) Please assemble the Miniature Plug (provided) for the Auto Iris Lens as shown in
the following diagram.
6

IRIS TERMINAL ~
COVER
DCDRIVE VIDEO DRIVE
1 CONTROL - (DMP- ) 12V
3
VIDEO
3
I 2 CONTROL+ N C
PLUG 4. DRIVE - GND
2
(h) Connect the
Plug ofthe Lens to the Iris terminal on the back of the camera.
VIDEO OUTPUT ,,
OU VIDEO OU
LEVEL ADJUSTOR ~~ - __ ~ i LME
OFT DL OFF ,
DC -7VTDE3 ‘
I CONTROL (DMP ) IZV
2 COmm+rNT
BACK VIEW
AUTO IRIS LENS
(c) Please set the Auto Shutter switch on the hack of the camera to “OFF”position
and then adjust the focus. The “AI” switch is for the selection of different type of
Auto Iris Lens. For the Video
Auto Iris Lens, please adjust the “ALC” and “IRIS
LEVEL” on the Lens to obtain the optimum setting. For the DC (Direct Drive)
Auto Iris Lens, please adjust the LEVEL ADJUSTOR on the back
of the camera
for the optimum setting.
7

COLLECTIVE SURVEILLANCE SYSTEM
,-, COLLECTIVE SURVEILLANCE SYSTEM
L 4000 _-1
FRONT VIEW END VIEW
8

Specifications:
CCD Sensor
Total Number of
Pixels
Number of Effective
Pixels
Chip Size
Horizontal Sync.
IV 380-E24A IV 380-C24A
1/3" 1/3"
542 (H) X 492 (V) 542 (€3) X 582 (V)
5 12(H) X 492 (V) 5 12(H) X 582 (V)
6.4mm
(H) X 6.4mm (H) X
5.24mrn (V) 5.24mm (V)
15.750 KHz 15.625 KHz
Frequency
Vertical Sync.
Frequency
Synchronzation
60
Hz 50 Hz
Internal & External Internal & External
Horizontal Resolution
Vertical Resolution
S/N Ratio
(Line Lock) Selectable (Line Lock) Selectable
380 Lines 380 Lines
400 Lines 400 Lines
47.5 dB 47.5 dB
Gamma Correction
AGC
Automatic Electronic
Shutter
Auto Iris Control
Minimum Illuminance
Scanning
Video Out
Lens Mount
Power Supply Voltage
(AGC
Off) (AGC Off)
0.45 0.45
Yes Yes
OdOff Manual OdOffManual
(1160
- 1110000Sec.) (US0 - 1110000 Sec.)
Yes Yes
(Video
& DC Drive) (Video & DC Drive)
(Modes Selectable) (Modes Selectable)
0.1 Lux.
(F 1.4)
0.1 Lux. (F1.4)
2:
1 Interlace 2: 1 Interlace
CS or C mount CS or
C mount
1 vp - p 7522 1 vp - p 75Q
(Changeable Adaptor) (Changeable Adaptor)
24V AC
+I- 10% 24V AC
+I- 10%
50 Hz
165mA max.
- 10°C - +50"C
Semi - circular
Range
Power Consumption
Operation Temp.
I 52 X 57 X 144mm 1 52 X 57 X 144mm
60
Hz
165mAmax.
- 10°C - +50°c
Range
Operation Temp.
Power Consumption 60
Hz 50 Hz
165mAmax. 165mA max.
- 10°C - +50°c
- 10°C - +50"C
Dimensions Semi
- circular Semi - circular
Dimensions I Semi - Circular