Inter-m RC-100 User manual

RC-100 Remote Controller
Operation Manual

Unpacking and Installation
Although it is neither complicated to install nor difficult to
operate your set, a few minutes of your time is required
to read this manual for a properly wired installation and
becoming familiar with its many features and how to use
them. Please take a great care in unpacking your set
and do not discard the carton and other packing
materials. They may be needed when moving your set
and are required if it ever becomes necessary to return
your set for service.

1
RC-100(REMOTE CONTROLLER)
Contents
Cautions for Handling and Installation ..............2
Method to put cell in..........................................3
Accessory .........................................................3
Function of remote controller button .................4
Method to operate remote controller.................7
When a remote controller does
not properly operate..........................................8
Specifications ......................................................9
Service
Procedures.......................................................10
Schematic ........................................................10
Parts List ..........................................................10
Warranty ..............................................................11

2RC-100(REMOTE CONTROLLER)
Cautions for Handling and Installation
- Don’t disassemble the unit. Otherwise, the unit may fail.
- Don’t put or soak the unit in water. Otherwise, the
unit may fail.
- Don’t use other cells than designated. Don’t
charge them.
In addition, don’t mix new cells with old ones for use.
Fracture of cells and leak of liquid may result in
fire, physical injury or contamination of the unit.
- Put cells in the unit as described while taking care
of polarity indication(+, - direction).
If putting them in, fracture of cells and leak of
liquid may result in fire, physical injury or
contamination of the unit.
- Don’t heat, disassemble, or put in fire and water.
Fracture of cells and leak of liquid may result in
fire, physical injury or contamination of the unit.

Method to put cell in
①Separate the cover behind a remote controller.
Separate the unit after removing screws behind
a remote controller using a L-wrench.
②Put cells in.
A 1.5V AAA type of 2 cells is required. Put cells
in the unit after checking a (+) or (-) pole.
③Cover the cover.
Tighten screws after covering.
Accessory
Manual
3
RC-100(REMOTE CONTROLLER)
L-wrench
RC-100
Battery
①
②
③

Function of remote controller button
1
1
. Power button
Power ON/OFF the system.
22
2
. Function selection switch
Set switches to match with the
type of a system to operate.
Applied function is changed
depending on setting position.
3
3
. Numeric button
Used when selecting a track of
CD and the memorized frequency
address of a tuner.
44
4
. Adjust output level of the Volume
Up/Down button AMP.
- VOL▲/VOL▼: Put the
volume level Up/Down.
55
5
. Source Select Button
Select input source of the AMP.
4RC-100(REMOTE CONTROLLER)

6
6
. CD Function Button
-▶/
III
: Play/Pause
-■: Stop
DISC SKIP : Select a disc to play.
(Equivalent to CD Changer)
REPEAT : Select the Play Repeat mode.
- ■ ◀◀-▶▶ ■ : Used when searching the
played music forward or backward.
-◀◀-▶▶: Used when moving a track
forward or backward during play.
77
7
. TUNER Function Button
-
▼TUNING▲: Used when searching
broadcast frequency.
- ▼PRESET▲: Used when selecting
memorized broadcast frequency.
AM/FM: Used when selecting
AM and FM broadcast.
5
RC-100(REMOTE CONTROLLER)

8
8
. DECK Function Button
This button is used when operating the
deck mounted on the PA system.
- TAPE A/B : Used when selecting a
deck to play.
- ◀: Play the rear side of a tape (RWD).
- ▶: Play the front side of a tape (RWD).
- ◀◀ : Rewind
- ▶▶ : Fast wind
- ■: Stop
6RC-100(REMOTE CONTROLLER)

Method to operate remote controller
1
1
. Set switches to match with the system to
operate the function selection switch.
•PA :
PA system where tuner, CDP or DECK is
mounted on.
•CD : CD player not be produced
•TU : Tuner not be produced
•HOLD : Function to hold the whole function which
protects the unit from careless manipulation.
※Of our products, only those equipped with the receipt
part of a remote controller may be remotely
operated and some products may be excluded.
22
2
. Press the relevant button after pointing toward the
receipt part of a remote controller of the system.
Manipulation distance is about 7m within the
left or right angle of 30°.
The longer the using period of a cell, the shorter
manipulation distance further becomes lessen.
33
3
. If not using a remote controller, place the
function selection switch on HOLD.
7
RC-100(REMOTE CONTROLLER)

When a remote controller does not properly operate
1
1.
Replace cells of a remote controller with new
one if distance significantly becomes more
than usual time. If using bad cells, leak of
liquid may cause failure of the system.
22
2.
If a fluorescent lamp around the system is 3-
waveform, distance of manipulation may be
reduced to more than the half. In this case, use
it immediately in front of the receipt part of a
remote controller of the system.
3
3.
Remove dusts where dusts are severely laid
between the transmit part of a remote
controller of the system and the receipt part.
8RC-100(REMOTE CONTROLLER)