Intercoastal CFL-420RB Operating instructions

CFL-420RB/CFL-42BN
CFNL-420RB/CFNL-42BN
CFLM-4250RB/CFLM-425BM
.
- 1- 4 :
__,,,,.,,,,.,,,,__-.-..--- I:2;. -:.-; 'l.;{i
Owners Manual
and
Installation Instructions
'
'
'

-
Make sure to tu m off electricity at main switch before wiring or servicing fan
in order to avoid pos s ible electrical shock.
All electrical wiring must conform to national and local Electrical Codes.
Make sure the fan is electricaUy grounded to avoid possible electrical shock.
Fan should be mounted a minimum of 7 feet above the floor to the fan blade
It should be a minimum of 20
1
inches from any wall to the blade tip.
Fan should not be mounted in an area where it might become wet.
The outlet box mu st be able to support a minimum weight of 50lbs . and
marked•acceptable for fan support" .Plastic outlet boxes are not recommended
for ceiling fan install a tion . You may use your existing box as long as it is
acceptable for fan support.If you have any doubts,check with a qualified
electrician. Your dealer will have the necessary products for safe installation of
your fan.
Never attach the b lades to your ceiling fan before the fan is mounted to the
ceiling. Do not oper a te your ceiling fan before the blades are installed.
For safety and best operating results, we recommend that you have a
qualified electrician a ssemble and install your fan.
WARNING! TO REDUCE THE RISK OF PERSONAL INJURY,00 NOT
BEND THE BLADE CARRIERS WHEN INSTALLING THE BRACKETS,
BALANCING THE BLADES,OR CLEANING THE FAN.DO NOT INSERT
FOREIGN OBJECTS IN BETWEEN ROTAONG FAN BLADES.
WARNING! TO REDUCE THE RISK OF FIRE,ELECTRICAL SHOCK,
OR PERSONAL IN JURY,MOUNT THE FAN TO AN OUTLET BOX
MARKED"ACCEPTABLE FOR FAN SUPPORT".
2

3
FIGURE 1
MO U NT I NG BRACKE T
STEP2
Re mo ethe temporary screws Installed to
a and-freewirlng , whil e ho l ding
otor unit upward.Insert on .e end of the
motor mounting bracket I nto the slot and
the other and of motor moun t ing into the
other slot in mounting platea nd adjust
moto r mou n ting until tabs on each side
fall into place In mounting pla te slot.
Secure tightly with screws and washers
provided.Align the 4 holes on the motor
housing with the holes on the mounting
bracket. Then attach screws p rovided.
Se&Figure2
STEP 1
Secure the bracket to the ceiling ouUet box using
screws provided wit h the outlet box attach
securely . There should be no movement between
the bracket and outlet box.See Figure1 .
~.__MOUNTING BRACKET
FIGURE2
II. MAKING ELECTRICAL
CONNECTIONS
FIGURE 3
WARNING: DISCONNECTPOWERHIH
1. Attach the green wire form the fan to the ground
wire In tile junction box.
2. Attach the black wire and blue wire from the fan to
the black wire in the junction box.
3. Attach the white wire fron th e fan to the white wire in the junction box.
4.Each of the above connections should be made as light as possible using a proper size
plastic wire nul Then fold the connected wire and push inside the junction box.
u

(A] 1 HA GING BRACKETS
(BJ 1 FAN MOTOR
(C) 1 SWITCH HOUSINGASSEMBLY
(OJ 1 MO TOR HOUSING
(EJ 1 FA N KIT
FI GURE 1
(F)
~
(GI
(f) 4 FAN
BLADES
FIGURE2
(GJ
4 BLADES HOLDERS
(ff) 1 HARDWAREBAG --------===Clil"I~
CONTAINS: a 2 WOOD SCREWS ----- ______. ...
b 2 HOUSINGSCREWS~ ------ 0
c 13 BLADE SCREWS •
d
13 FIBER WASHERS • ..
e 3 WIRE NUTS O-
f 2 FAN PULL TASSEL------•
g 9 BLADE HOLDER SCREWS . ..
( I I 1 BALANCING KIT
(1 BAG)
4

5
OPTIONAL WIRING DI AGRAMS
WALL SWITCH
FI GURE4
LIGHT& FAN
SWITCH TO
CONTROL LIGHT
JUNCTION BOX
BLACK BLACK
(2 WALL SWITC HES)
WALL SWI T CH
FAN BLADE TO BLADE HOLDERASSEMBLY
FIGURES
Attach the tan blade to bladeholderusing screws and washers
suppiled.Tighten each screwstarting with the
center screwmaking
surethe blade Isstraight.Fasten the blade and assembly to the
mot or using the screws supplied.Seefiaure6
NOT E :THE BLADE HOLDERS AND BLADES HAVE BEEN CAREFULLY
BA LA NCED TO AVOID WOBBLING WHEN THE FANIS OPERST1NG.BE
CAR E FUL NOTTO BEND OR DAMAGE THEM.