Interlogix SDX-135Z-433 User manual

1
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
Attention: Please take a few minutes to thoroughly read this user guide which should be
saved for future reference.
NOTE: Leave this user guide with the home owner.
You do NOT need a home wi-fi system to use these units. Multiple wireless units create
their own independent wireless alarm network.
SDX-135Z-433
Wireless Interconnected Smoke/Heat/
Freeze sensor 433-63
User Guide

2P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
Thank you for purchasing this Interlogix smoke alarm
This model is powered by a non-replaceable, long life sealed lithium battery system, and
includes SMART HUSH®Control to temporarily silence nuisance alarms. It is capable of
Wireless Interconnect with compatible units.
READ SECTION 8: Installation / Activation / Wireless, before powering the units.
You do NOT need a home wi-fi system to use these units. Multiple wireless units
create their own independent wireless alarm network.
Teach children how to respond to the alarm and that they should never play with the unit. Your
Interlogix smoke alarm was designed for use in a residential environment. It is not designed for
use in a recreational vehicle (RV) or boat.
NOTE: Please thoroughly read this user guide and save the document for future reference and
to pass on to any subsequent owner.
The manufacturer recommends replacing this alarm ten years from the date code on back of
the alarm.
Customer Service: 1-855-286-8889
Please write down the below information and have this at hand when you call.
Model (on back): _________________
Date Code (on back): _________________
Date of Purchase: _________________
Where Purchased: _________________
Date to Replace: _________________

3
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
Contents
1. Smoke Alarm: What To Do When The Alarm Sounds..................................................... 4
2. Other Alarm Visual And Audible Indicators ......................................................................5
3. Troubleshooting Guide .......................................................................................................7
4. Introduction, Product Features & Specifications..............................................................9
5. Limitations Of Smoke Alarms...........................................................................................13
6. Recommended Locations For Smoke Alarms ...............................................................14
7. Locations To Avoid ............................................................................................................16
8. Installation / Activation / Wireless ...................................................................................17
8.1 Set Up A Wireless Alarm Network (Wireless Interconnect) ..................................................18
8.2 Adding Alarms to an Existing Wireless Interconnected Network .........................................20
8.3 Resetting an Alarm’s Wireless Interconnect Settings ...........................................................21
9. Operation and Testing…………………………………………………….............................22
10. Recognizing Nuisance Alarms ………………………………………….............................23
11. Battery ………………………………………….................................................................... 24
12. Permanently Disable Alarm / Discharge Battery .......................................................... 25
13. Cleaning Your Alarm ……………………...........................................................................26
14. Good Safety Habits ……………………........................................................................… 27
15. Service And Warranty …………………........................................................................…29

4P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
1. Smoke Alarm: What To Do When the Alarm Sounds
Smoke alarm pattern is three long beeps, a 1.5 second pause, and three long beeps repeating.
The red LED blinks in time with alarm pattern.
•Alert small children in the home as well as anyone else that might have difficulty recognizing the
importance of the alarm sounding or that might have difficulty leaving the area without help.
•Leave immediately by your escape plan. Every second counts, so don’t waste time getting dressed or
picking up valuables.
•In leaving, don’t open any inside door without first feeling its surface. If hot, or if you see smoke seeping
through cracks, don’t open that door! Instead, use your alternate exit. If the inside of the door is cool,
place your shoulder against it, open it slightly and be ready to slam it shut if heat and smoke rush in.
•If the escape route requires you to go through smoke, stay close to the floor where the air is cleaner.
Crawl if necessary, and breathe shallowly through a cloth, wet if possible.
•Once outside, go to your selected meeting place and make sure everyone is there.
•Call the fire department from your cell phone outside, or from your neighbor’s home-not from yours!
•Don’t return to your home until the fire officials say that it is all right to do so.
•There are situations where a smoke alarm may not be effective to protect against fire as stated in the
NFPA Standard 72. For instance:
a) smoking in bed
b) leaving children home alone
c) cleaning with flammable liquids, such as gasoline
NOTE: See Section RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

5
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
2. Other Alarm Visual and Audible Indicators
Operational Mode Visual Indications Audible Indications Action/Note:
Normal Operation
(standby)
One GREEN LED blink
every 60 seconds.
Freeze Warning One RED LED blink
every 20 seconds.
None None. Flashing continues
while condition exists.
Tamper Condition One RED LED blink
every 30 seconds
(after a 3 minute
delay).
Alarm chirps once when tamper
condition is rst sensed, then the
alarm will chirp every 30 seconds
after a 3 minute delay.
Reattach alarm to its trim
plate, otherwise ashing and
chirping will continue while
condition exists.
System Test Mode Rapidly ashing RED
LED for 10 seconds
duration
1 alarm chirp when magnet
detected, 2 alarm chirps when System
Test mode enabled
Hold magnet next to button
for 4 seconds. See Figure 5.
Local Alarm Test
(button press when
no alarm condition
is present)
Flashes RED, AMBER,
GREEN, then current
protocol
Temporal T3 pattern Allow completion of test or
perform button press to
cancel, return to normal
operation
System Alarm Test
(button press in System
Test Mode when no
alarm condition is
present)
Flashes RED, AMBER,
GREEN, then current
protocol on each alarm
in the network
Temporal T3 pattern Allow completion of test or
perform button press to
cancel, return to normal
operation.
Smoke/Heat Alarm
Memory (alarm has
experienced an alarm
event within the last
hour)
Alternating ashing
RED and AMBER
LEDs. 1 second RED/1
second AMBER/ 10
seconds OFF,
repeating for 1 hour
None Press test button to clear
alarm memory, or allow 1
hour time out to return to
normal operation. NOTE:
standard test sequence will
follow. (Push/release button
again to cancel test).

6P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
Operational Mode Visual Indications Audible Indications Action/Note:
Smoke Alarm Hush
Mode (SMART HUSH
®
CONTROL)
Red LED blinks
every 2 sec.
After button push: Smoke alarm pattern
stops. (If there is too much smoke, smoke
alarm pattern continues.)
This feature is to be used
only when a known alarm
condition, such as smoke
from cooking, activates the
alarm.
Locate None After button push on non-initiating unit,
only initiating unit continues alarm
pattern.
Use this to quickly locate the
alarm source and determine
if alarm is nuisance or real.
Initiating Alarm Alarm
(multiple alarms in an
interconnected system)
Green LED blinks once
per sec indicating that
this is the unit
initiating the alarm in
an interconnected,
multiple alarm, system.
Unit in Smoke Alarm mode. During alarm, the initiating
alarm red blink will be inter-
rupted by a green blink.

7
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
3. Troubleshooting Guide
Trouble Condition Visual Indications Audible Indications Action:
Fault Mode/Fatal
Error
One AMBER
LED blink every 5
seconds.
Alarm chirps
every 30 seconds.
1. Push the Test/Hush button once to attempt to
reset the alarm.
The RED LED will blink out an Error Code
(number of blinks) when the Test/Hush button
is pushed/released once.Report the number of
blinks to Customer Service, if needed.
2. Clean your alarm. See “Cleaning Your Alarm”
for instructions.
3. Remove alarm from service. If fatal error
cannot be cleared, permanently discharge and
decommission the alarm.
Network Error
(if an alarm loses
wireless interconnect
connection due to
loss of signal)
One AMBER
LED blink every 5
seconds.
Alarm chirps every
30 seconds. (NOTE:
chirps only occur if
network includes more
than 2 alarms.)
Remove device from mounting bracket, and try
rotating and re-installing the device in a different
orientation on the mounting bracket. This might
align the antenna in a better position.
1. Push the Test/Hush button once to silence the
audible indication for 24 hours at a time.
The RED LED will blink out an Error Code
(number of blinks) when the Test/Hush button
is pushed/released once. Report the number of
blinks to Customer Service, if needed.
2. Follow instructions in “Resetting an alarm
Alarm’s Wireless Interconnect Settings.”, then
attempt to rejoin the network by following the
instructions in ”Adding Alarms to an Existing
Wireless Interconnected Network .”*If the error
persists, remove, discharge, and replace the
alarm as soon as possible.
Network Error due to
loss of radio
(CCI supervision)
One AMBER
LED blink every 5
seconds.
Alarm chirps every 30
seconds, regardless of
the number of
alarms in the network.
1. Push the Test/Hush button once to silence the
audible indication for 24 hours at a time.
The RED LED will blink out an Error Code (4
blinks) when the Test/Hush button is pushed/
released once. Report the number of blinks to
Customer Service, if needed.
2. Remove, discharge, and replace the alarm as
soon as possible.

8P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
Trouble Condition Visual Indications Audible Indications Action:
Low Battery One AMBER LED blink
every 5 seconds.
Alarm chirps every 60
seconds
Remove, discharge, then dispose of
alarm. Replace as soon as possible.
End of Alarm
Life (EOL)
One AMBER LED blink
every 5 seconds.
Double alarm chirp every
30 seconds.
The RED LED will blink out an Error
Code of 9 blinks. Start of EOL will be
delayed if Night Detect is active.
Hush (for Network
Error, End of Life)
One AMBER LED blink
every 5 seconds.
Chirp temporarily
silenced for 24 hours.
Push the Test/Hush button to
initiate Hush for 24hrs.
Sensor Clean-
liness
Level (Clean-Me
Indication)
AMBER LED Clean-Me
blink sequence after
TESTING (PUSH TO TEST
BUTTON) temporal pattern
per “Operation and Testing”
None 1. Push the Test/Hush button to initiate
alarm test. Following the temporal
patterns, the AMBER LED will blink
the cleanliness status of the alarm:
0-1: Unserviceable fault; remove,
discharge, and replace the alarm.
2-3: Insensitive; requires cleaning per
“Cleaning Your Alarm” section.
4-7: Normal Sensitivity
8-9: Too sensitive, requires cleaning
per “Cleaning Your Alarm” section.
Alarm Fault: Number of RED LED Blinks (short
duration blinks) Wireless Fault: Number of RED LED Blinks (long duration
blinks)
7: Push to Test
8: Memory
9: Life Expiration
10: Smoke Chamber
12: Temperature Sensor Supervision
14: Smoke Drift Compensation
2: Fault Coordinator
3: Fault RFD
4: CCI Supervision
5: RFD Check In
6: RFD Time Sync

9
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
4. Introduction, Product Features and Specifications
Introduction
The Interlogix SDX-135Z-433 supervised photoelectric smoke alarm with heat and freeze sensors
is a self-diagnostic alarm with wireless interconnection, 10-yr sealed battery and sensor life, built-in
sounder, diagnostic/status LED, integrated fixed temperature and rate-of-rise heat sensor and a pre-
freeze condition indicator.
The SDX-135Z-433 uses a 918MHz transceiver for interconnection communication between net-
worked alarms. Up to 24 alarms can be a part of the same interconnected network.
The SDX-135Z-433 uses 10-year sealed-in lithium batteries ensuring continuous operation over the
10 year life of the alarm. This eliminates worry about battery removal or unauthorized deactivation of
the alarm. The self-activation feature activates the alarm when attached to the mounting bracket. At
the end of alarm life, the unit will chirp, indicating the alarm is in need of replacement (see
Troubleshooting Guide).
To help identify the date to replace the alarm, a label has been affixed to the side of the alarm. Write
the “Install date” in the space provided, and then write in the “Replace by” date (10 years from initial
power up) in permanent marker on the label prior to installing the alarm.

10 P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
Power 3V DC non-replaceable sealed lithium batteries
Smoke sensor Photoelectric
Temperature sensor NTC Thermistor
Battery life 10 years*
Alarm life 10 years
Audible alarm
Smoke/heat
85dB at 10’ @ 3.0 to 3.5 KHz pulsing alarm
Temporal T3 pattern
Single Unit Box Dimensions 142mmx149mm x 65mm (W x L x H)
Product Dimensions Ø142.3 ± 0.3mm x 59.0 ± 1.0mm
Smoke Sensitivity 2.32 +/- 1.35 %/ft. obscuration
Gross Weight (unit, pkg, etc) 465 grams
Net Product Weight 340 grams
Product Features and Specifications:

11
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
Rate-of-Rise (ROR)
heat detection
15°F/min (8.3C/min) monitoring above 85°F
(29.4°C)
Fixed temperature
heat detection
~135°F (57.2°C)
Freeze warning 41°F (5°C) ± 5°F (2.8°C)
Storage temperature -4 °F (-20°C) to 140°F (60°C)
Operating environment
Temperature
Relative humidity
32 °F to 100 °F (0 °C to 37.8 °C)
0 to 95% noncondensing
Regulatory
Listings
UL217
*3 year warranty.Not a battery performance claim.
Product Features and Specifications:

12 P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
Model Description
SDX-135Z-433 Wireless Interconnected Smoke/Heat/Freeze sensor 433-63.
UL217.
Accessories
SM-200 Smoke! In A Can (canned smoke) for functional testing of smoke
alarms
Product Ordering:

13
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
5. Limitations of Smoke Alarms
WARNING: PLEASE READ CAREFULLY AND THOROUGHLY
•Life safety from fire in residential occupancies is based primarily on early notification to occupants of
the need to escape, followed by the appropriate egress actions by those occupants.
•Fire warning systems for dwelling units are capable of protecting about half of the occupants in po-
tentially fatal fires. Victims are often intimate with the fire, too old or young, or physically or mentally
impaired such that they cannot escape even when warned early enough that escape should be pos-
sible. For these people, other strategies such as protection-in-place or assisted escape or rescue are
necessary.
•Leading authorities recommend that both ionization and photoelectric smoke alarms be installed to
help insure maximum detection of the various types of fires that can occur within the home. Ionization
sensing alarms may detect invisible fire particles (associated with fast flaming fires) sooner than pho-
toelectric alarms. Photoelectric sensing alarms may detect visible fire particles (associated with slow
smoldering fires) sooner than ionization alarms.
•A battery powered alarm must have a battery of the specified type, in good condition and installed
properly (This model has a sealed battery).
•Smoke alarms must be tested regularly to make sure the battery and the alarm circuits are in good oper-
ating condition.
•Smoke alarms cannot provide an alarm if smoke does not reach the alarm. Therefore, smoke alarms
may not sense fires starting in chimneys, walls, on roofs, on the other side of a closed door or on a
different floor.
•If the alarm is located outside the bedroom or on a different floor, it may not wake up a sound sleeper.
•The use of alcohol or drugs may also impair one’s ability to hear the smoke alarm. For maximum protec-
tion, a smoke alarm should be installed in each sleeping area on every level of a home.
NOTE: This alarm is not intended to alert hearing impaired individuals.

14 P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
6. Recommended Locations for Smoke Alarms
•Locate alarms in all sleeping areas. Try to monitor the exit path as the bedrooms are usually farthest
from the exit. If more than one sleeping area exists, locate additional alarms in each sleeping area.
•Locate additional alarms to monitor any stairway as stairways act like chimneys for smoke and heat.
•Locate at least one alarm on every floor level.
•Locate an alarm in every bedroom.
•Locate an alarm in every room where electrical appliances are operated (i.e. portable heaters or humid-
ifiers), as long as the room is environmentally controlled within the temperature and humidity ranges as
defined in the “Specifications” table.
•Locate an alarm in every room where someone sleeps with the door closed. The closed door may
prevent an alarm not located in that room from waking the sleeper.
•Smoke, heat, and combustion products rise to the ceiling and spread horizontally. Mounting the smoke
alarm on the ceiling in the center of the room places it closest to all points in the room. Ceiling mounting
is preferred in ordinary residential construction.
•When mounting an alarm on the ceiling, locate it at a minimum of 4” (10 cm) from the side wall.
•When mounting the alarm on the wall, use an inside wall with the top edge of the alarm at a minimum of
4” (10 cm) and a maximum of 12” (30.5 cm) below the ceiling.
•Put smoke alarms at both ends of a bedroom hallway or large room if the hallway or room is more than
30 feet (9.1m) long.
•Install smoke alarms on sloped, peaked or cathedral ceilings at or within 3ft (0.9m) of the highest point
(measured horizontally).
This equipment should be installed in accordance with the National Fire Protection Association’s 72 (Na-
tional Fire Protection Association, Batterymarch Park, Quincy, MA 02269).

15
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
ANYWHERE ALONG
THIS BOLD SURFACE
Locations permitted for smoke
alarms and smoke detectors
on tray-shaped ceilings.
ANYWHERE ALONG
THIS BOLD SURFACE
Locations permitted for smoke
alarms and smoke detectors
on tray-shaped ceilings.
ANYWHERE ALONG
THIS BOLD SURFACE
Locations permitted for smoke
alarms and smoke detectors
on tray-shaped ceilings.
ANYWHERE ALONG
THIS BOLD SURFACE
Locations permitted for smoke
alarms and smoke detectors
on tray-shaped ceilings.
ANYWHERE ALONG
THIS BOLD SURFACE
Locations permitted for smoke
alarms and smoke detectors
on tray-shaped ceilings.
ANYWHERE ALONG
THIS BOLD SURFACE
Locations permitted for smoke
alarms and smoke detectors
on tray-shaped ceilings.
Figure 1
Figure 2
Figure 3
NFPA 72 states: “Smoke alarms in
rooms with ceiling slopes greater
than 1 ft in 8 ft (.3m in 2.4 m)
horizontally shall be located on
the high side of the room.

16 P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
7. Locations to Avoid
•In the garage. Products of combustion are present when you start your automobile.
•Normal cooking may cause nuisance alarms. If a kitchen alarm is desired, it should have an alarm silence
feature or be a photoelectric type.
•Do not install within 6 ft. of heating or cooking appliances.
•Less than 4” (10cm) from the peak of an “A” frame type ceiling.
•In dusty areas. Dust particles may cause nuisance alarm or failure to alarm.
•In very humid areas (above 95% RH, non-condensing). Moisture or steam can cause nuisance alarms.
•In insect-infested areas.
•In an area where the temperature may fall below 32ºF (0C) or rise above 100ºF (37.8C), such as garages
and unfinished attics.
•Alarms should not be installed within 3 ft (.9m) of the door to a bathroom containing a tub or shower, forced
air supply ducts used for heating or cooling, ceiling or whole house ventilating fans, or other high air flow
areas.
•Do not install near vents, flues, chimneys or any forced/unforced air ventilation openings.
•Do not install near fans, doors, windows or areas directly exposed to the weather.
NOTE: Smoke alarms are not to be used with alarm guards unless the combination (alarm and alarm guard)
have been evaluated and found suitable for that purpose.
Smoke alarms cannot provide an alarm if smoke does not reach the alarm. Therefore, smoke alarms may not
sense fires starting in chimneys, walls, on roofs, on the other side of a closed door or on a different floor.

17
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
8. Installation / Activation / Wireless
You do NOT need a home wi-fi system to use these units. Multiple wireless units create their own indepen-
dent wireless alarm network (wireless interconnect between multiple alarms).
WARNING: THIS ALARM SHOULD BE INSTALLED BY A CERTIFIED TECHNICIAN.
WARNING: FAILURE TO PROPERLY INSTALL AND ACTIVATE THIS ALARM WILL PREVENT
PROPER OPERATION AND RESPONSE TO HAZARDS.
If you are installing alarms and will use the wireless interconnect function, proceed to section
8.1 “Set Up a Wireless Alarm Network (Wireless Interconnect)” If you are not using the
wireless alarm-to-alarm interconnect function, then proceed with the following two steps.
1. After selecting the proper location for the alarm, attach the mounting bracket (trim plate) to the wall or
ceiling. To ensure aesthetic alignment of the alarm with the hallway, or wall, the “A” line on the mount-
ing bracket (trim plate) must be parallel with the hallway when ceiling mounted or horizontal when wall
mounted.
2. Install the alarm fully on the mounting bracket (trim plate) by rotating the alarm in a clockwise
direction.
NOTE: Installing the alarm on the mounting bracket (trim plate) will automatically activate the battery. The
power up sequence is indicated by the LED ring slowly glowing GREEN on/off one time.
NOTE: Alarms will emit a series of slow RED LED glowing on/off as the alarm searches for a wireless
network. If you are intending to use the alarms without the wireless interconnect function, ignore these
notifications, and the wireless interconnect function will eventually turn off (~15 minutes) OR to immediately
finish this process, push the Test/Hush button until two beeps are heard (approximately 4 seconds). The
LED will change to glowing GREEN on/off every second. Repeat the button push/hold for another 4
seconds, until two beeps are heard, and then release the button. This will close the network.
•When the network has been closed, each alarm’s GREEN LED will change from glowing on/off every
second to flashing once every 60 seconds to indicate normal operation.
NOTE: The battery activation is a one-time feature. After activation, the battery cannot be turned off, and
can only be discharged at the end of unit life. If the alarm is removed from the mounting plate, the battery
will remain active. See Permanently Disable Alarm / Discharge Battery section to de-energize the alarm.

18 P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
8.1 Set up a Wireless Alarm Network (Wireless
Interconnect)
1. Remove all wireless alarms from their packaging (suggest using a table and activating all alarms in a group).
2. Power on all alarms by attaching the alarms onto the mounting bracket (trim plate) to activate the bat-
tery, or by carefully turning the red activation wheel with a screwdriver. See Figure 4.
•
The GREEN LED will fade on and off once, then the RED LED will begin fading on/off every 3 seconds.
NOTE: If no further steps are taken within 15 minutes of initial power up, the wireless function will turn
off. The alarm will then perform as a single station alarm.
WIRELESS
These models have wireless alarm interconnect capability. When one interconnected alarm sounds an
alarm, all other compatible wireless alarms in the wireless alarm network will alarm.
A maximum of 24 compatible devices may be interconnected in a multiple station arrangement.
This alarm is not designed to be interconnected with other manufacturer’s products, unless otherwise
specified.
WIRELESS INTERCONNECT MODEL COMPATIBILITY
The following Interlogix models can be interconnected using wireless interconnect:
• SDX-135Z-433, HDX-135Z-433
• Maximum distance between wireless interconnect models is 300 feet in open air.
Figure 4

19
P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
3. After all alarms are powered on and the RED LED is glowing on/off, push and hold the Test/Hush button
on any one alarm until two beeps are heard (approximately 4 seconds) and then release the button. This
alarm will automatically create a new wireless network.
• A brief series of quick GREEN LED blinks will occur and then the GREEN LED will fade on/off every
second on the button-pushed alarm (network creator).
4. Wait for the other wireless alarms to join the wireless network.
• A brief series of quick GREEN LED blinks will occur and then the GREEN LED will fade on/off
approximately every 3 seconds.
NOTE: At this point, you can push/release the test button once on any alarm, and the RED LED will
flash the number of enrolled alarms.
5. Wait for the network setup to timeout (approximately 15 minutes), OR to immediately close the network,
push the Test/Hush button until two beeps are heard (approximately 4 seconds) and then release the
button. The network can be closed from any device enrolled in the network.
• When the network has been closed, each alarm’s GREEN LED will change from glowing on/off
every second to flashing once every 60 seconds to indicate normal operation.
6. After selecting the proper location for your alarm, attach the mounting bracket to the wall or ceiling. To
ensure aesthetic alignment of the alarm with the hallway, or wall, the “A” line on the mounting bracket
must be parallel with the hallway when ceiling mounted or horizontal when wall mounted.
• Install the alarm fully on the mounting bracket (trim plate) by rotating the alarm in a clockwise direc-
tion. NOTE: The alarm will mount to the bracket in 4 positions (every 90 degrees).
7. The alarm is now activated. After installation / activation, test your alarm as described in
Operation and Testing section.

20 P/N 0320-7201-00 • REV A • ISS 14MAR18 ©2018 United Technologies Corporation
8.2 Adding Alarms to an Existing Wireless
Interconnected Network
For various reasons, you might want to add additional alarms to your existing wireless interconnection
network.
1. Remove the new alarm from its packaging.
2. Choose one existing, installed alarm (not the new alarm). Place and hold a magnet for four seconds
on the cover of the existing alarm in the network at the designated location per Figure 5. The alarm will
beep once when the magnet is detected, then the alarm will beep twice and will start flashing the RED
LED rapidly to indicate the alarm is in System Test Mode.
3. Push and hold the test button on the same alarm (in System Test Mode) until two beeps are heard
(approximately 4 seconds), and then release the button.
• The button-pushed alarm will cause the GREEN LED to fade on/off on each alarm in the existing
network to signal that the wireless interconnection network has been opened.
NOTE: From this point, you have fifteen (15) minutes to power up the new alarm.
4. Power up the new wireless alarm by twisting the alarm onto the mounting bracket (trim plate) to activate
the battery, or by carefully turning the red activation wheel with a screwdriver. See Figure 4.
• After initial GREEN LED on/off sequence, the new alarm’s RED LED will fade on/off every 3 sec-
onds as it searches for the network.
• A fast GREEN LED flickering, followed by a slow GREEN LED fading on/off confirms the new alarm
has found and joined the existing wireless interconnection network.
5. Wait fifteen (15) minutes for the network setup to timeout, OR to immediately close the network, push
and hold the test button on any device enrolled in the network until two beeps are heard (approximately
4 seconds), and then release the button.
• GREEN LED flashes once every 60 seconds on the new alarm to indicate normal operation.
6. After selecting the proper location for your alarm, attach the mounting bracket to the wall or ceiling. To
ensure aesthetic alignment of the alarm with the hallway, or wall, the “A” line on the mounting bracket
must be parallel with the hallway when ceiling mounted or horizontal when wall mounted.
• Install the alarm fully on the mounting bracket (trim plate) by rotating the alarm in a clockwise direc-
tion. NOTE: The alarm will mount to the bracket in four positions (every 90 degrees).
7. The alarm is now activated. After installation / activation, test your alarm as described in Operation and
Testing section.