Interlogix ES2402-24P-2C User manual

IFS ES2402-24P-2C ES2402-16P-2C
ES2402-8P-2C User Manual
P/N 1073043 • REV A • ISS 19AUG15

2
C
opyright
©
2015 United Technologies Corporation
Interlogix is part of UTC Building & Industrial Systems,Inc. a unit of United
Technologies Corporation.
All rights reserved.
Trademarks and
patents
Th
e ES2402 Series name and logo are trademarks of United Technologies.
Other trade names used in this document may be trademarks or registered
trademarks of the manufacturers or vendors of the respective products.
Manufactu
rer
Interlogix
3211 Progress Drive, Lincolnton,
NC 28092 USA
Authorized EU manufacturing representative:
UTC Climate Controls & Security B.V.,
Kelvinstraat 7, 6003 DH Weert, Netherlands
Intended use
Use this product only for the purpose it was designed for; refer to the data sheet
and user documentation for details. For the latest product information, contact
your local supplier or visit us online at www.interlogix.com.
Certification
N4131
FCC compliance
This equip
ment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commerc
ial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
You are cautioned that any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to operate
the equipment.
ACMA compliance
Notice!
This is a Class A product. In a domestic environment this product may
cause radio interference
in which case the user may be required to take
adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES
-003.
Cet appareil numérique de la classe A est conforme á la norme NMB
-003du
Canada.
European Union
directives
2004/108/
EC (EMC Directive): Hereby, UTC Building & Industrial Systems, Inc.
declares that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.
Contact Information
For contact information, see
www.interlogix.com or
www.utcfssecurityproducts.eu
.

3
TABLE OF CONTENTS
1. INTRODUCTION.................................................................................................................... 6
1.1 Packet Contents ...........................................................................................................................................6
1.2 Product Description .....................................................................................................................................7
1.3 How to Use This Manual ..............................................................................................................................9
1.4 Product Features........................................................................................................................................10
1.5 Product Specifications ..............................................................................................................................12
2. INSTALLATION ................................................................................................................... 18
2.1 Hardware Description ................................................................................................................................18
2.1.1 Switch Front Panel ..............................................................................................................................................18
2.1.2 LED Indications ...................................................................................................................................................19
2.1.3 Switch Rear Panel...............................................................................................................................................22
2.2 Installing the Switch...................................................................................................................................23
2.2.1 Desktop Installation .............................................................................................................................................23
2.2.2 Rack Mounting.....................................................................................................................................................24
2.2.3 Installing the SFP transceiver ..............................................................................................................................25
3. SWITCH MANAGEMENT .................................................................................................... 27
3.1 Requirements..............................................................................................................................................27
3.2 Management Access Overview.................................................................................................................28
3.3 Web Management .......................................................................................................................................28
3.4 SNMP-based Network Management .........................................................................................................29
4. WEB CONFIGURATION...................................................................................................... 30
4.1 Main Web Page ...........................................................................................................................................33
4.2 System.........................................................................................................................................................35
4.2.1 System Information..............................................................................................................................................35
4.2.2 IP Configurations .................................................................................................................................................36
4.2.3 Password Setting.................................................................................................................................................37
4.2.4 Factory Default ....................................................................................................................................................37
4.2.5 Firmware Update .................................................................................................................................................38

4
4.2.6 Reboot.................................................................................................................................................................40
4.3 Port Management .......................................................................................................................................41
4.3.1 Port Configuration................................................................................................................................................41
4.3.2 Port Mirroring.......................................................................................................................................................43
4.3.3 Bandwidth Control ...............................................................................................................................................45
4.3.4 Broadcast Storm Control......................................................................................................................................46
4.3.5 Port Statistics.......................................................................................................................................................47
4.4 VLAN............................................................................................................................................................49
4.4.1 VLAN Overview ...................................................................................................................................................49
4.4.2 VLAN Basic Information.......................................................................................................................................51
4.4.2.1 Port-based VLAN mode.............................................................................................................................51
4.4.2.2 Ta g -based VLAN Mode .............................................................................................................................51
4.4.3 VLAN Port Configuration .....................................................................................................................................53
4.4.3.1 Port-based VLAN Mode.............................................................................................................................53
4.4.3.2 Ta g -based VLAN Mode .............................................................................................................................54
4.4.4 Multi to 1 Setting..................................................................................................................................................55
4.5 Quality of Service .......................................................................................................................................56
4.5.1 QoS overview ......................................................................................................................................................56
4.5.2 Priority Mode .......................................................................................................................................................57
4.5.3 Class of Service Configuration ............................................................................................................................57
4.5.4 TCP/UDP Port Based QoS ..................................................................................................................................58
4.6 Security .......................................................................................................................................................60
4.6.1 MAC Address Filter..............................................................................................................................................60
4.6.2 TCP/UDP Filter ....................................................................................................................................................61
4.7 Spanning Tree.............................................................................................................................................63
4.7.1 STP Bridge Settings ............................................................................................................................................69
4.7.2 STP Port Settings ................................................................................................................................................71
4.7.3 Loopback Detection.............................................................................................................................................73
4.8 Trunking Setting .........................................................................................................................................75
4.8.1 Link Aggregation Settings....................................................................................................................................77
4.9 PoE Setting .................................................................................................................................................79
4.9.1 Power over Ethernet Powered Device.................................................................................................................79
4.9.2 PoE Status...........................................................................................................................................................80
4.9.3 PoE Port Setting ..................................................................................................................................................81
4.9.4 Port Sequential ....................................................................................................................................................84
4.10 Configuration Backup / Upload ..............................................................................................................86

5
4.11 Misc Operation..........................................................................................................................................87
4.12 SNMP .........................................................................................................................................................88
4.13 Logout .......................................................................................................................................................90
5. SWITCH OPERATION ......................................................................................................... 91
5.1 Address Table .............................................................................................................................................91
5.2 Learning ......................................................................................................................................................91
5.3 Forwarding & Filtering ...............................................................................................................................91
5.4 Store-and-Forward .....................................................................................................................................91
5.5 Auto-Negotiation ........................................................................................................................................92
6. Power over Ethernet Overview.......................................................................................... 92
7. TROUBLESHOOTING......................................................................................................... 95
APPENDIX A ........................................................................................................................... 96
A.1 Switch's RJ45 Pin Assignments...............................................................................................................96
A.2 10/100Mbps, 10/100BASE-TX....................................................................................................................96

6
1. INTRODUCTION
Thanks you for purchasing ES2402 Series Switch, 10/100BASE-TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo Web Smart
Ethernet Switch, 8 port, 16 port and 24 port “PoE Web Smart Switch” mentioned in this Guide refers to the ES2402 Series.
1.1 Packet Contents
Open the box of the PoE Web Smart Switch and carefully unpack it. The box should contain the following items:
The PoE Web Smart Switch x1
Quick Installation Guide x1
SFP Dust Cap x2
Rubber Feet x4
Rack Mount Accessory Kit x1
Power Cord x1
If any item is found missing or damaged, please contact your local reseller for replacement.

7
1.2 Product Description
Ideal Solution for Secure IP Surveillance Infrastructure
Particularly designed for the growing popular IP surveillance applications, IFS ES2402 SERIES 802.3at PoE web smart switch
is positioned as a surveillance switch with the central management of remote power control and IP camera monitoring. The
ES2402 SERIES provides intelligent PoE functions along with 8/16/24 10/100BASE-TX ports featuring 30-watt 802.3at PoE+
with RJ45 copper interfaces and 2 Gigabit TP/SFP combo interfaces supporting high-speed transmission of surveillance
images and videos.
Perfectly-integrated Solution for PoE IP Camera and NVR System
Being different from the general IT industry PoE switch which usually contains 8, 16 or 24 PoE ports, the ES2402 SERIES
provides 8/16/24 802.3at PoE+ ports for catering to medium to large scale of IP surveillance networks at a lower total cost. With
its 5.6Gbps/7.2Gbps/8.8Gbps high-performance switch architecture and 120-watt/220-watt/360-watt PoE power budget, the
recorded video files from 8/16/24 PoE IP cameras can be powered by the ES2402 SERIES and saved in the 8/16-channel NVR
systems or surveillance software to perform comprehensive security monitoring. For instance, one ES2402 SERIES can be
combined with one 8/16-channel NVR and 8/16 PoE IP cameras as a kit for the administrators to centrally and efficiently
manage the surveillance system in the local LAN and the remote site via Internet. Please refer to following ES2402 SERIES
application example.

8
Intelligent LED Indicator for Real-time PoE Usage
The ES2402 SERIES helps users to monitor the current status of PoE power usage easily and efficiently by its advanced LED
indication. Called “PoE Power Usage”, the front panel of the ES2402 SERIES Fast Ethernet PoE+ Switch has four orange
LEDs indicating PoE power usage.
Robust Layer 2 Features
The ES2402 SERIES can be programmed for advanced switch management functions such as dynamic port link aggregation
(LACP), Spanning Tree Protocol (STP), IGMP Snooping v1, v2, bandwidth control and L2/L4 security control.The ES2402
SERIES provides IEEE 802.1Q tagged VLAN, port-based VLAN and MTU VLAN. Via aggregation of supporting ports, the
ES2402 SERIES allows the operation of a high-speed trunk combining multiple ports and supports fail-over as well.
Flexible and Extendable Uplink Solution
The ES2402 SERIES provides 2 extra Gigabit TP/SFP combo interfaces supporting 10/100/1000BASE-T RJ45 copper to
connect with surveillance network devices such as NVR, Video Streaming Server or NAS to facilitate surveillance
management. It can be connected with the 1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber transceiver and uplinks
to backbone switch for monitoring control center in long distance.The distance can be extended from 550m to 2km (multi-mode
fiber), even going up to above 10/20/30/50/60/70km (single-mode fiber or WDM fiber). They are well suited for applications
within the enterprise data centers and distributions.

9
1.3 How to Use This Manual
This User Manual is structured as follows:
Section 2, INSTALLATION
The section explains the functions of the Switch and how to physically install the PoE Web Smart Switch.
Section 3, SWITCH MANAGEMENT
The section contains the information about the software function of the PoE Web Smart Switch.
Section 4, WEB CONFIGURATION
The section explains how to manage the PoE Web Smart Switch by Web interface.
Section 5,SWITCH OPERATION
The chapter explains how to does the switch operation of the PoE Web Smart Switch.
Section 6,Power over Ethernet Overview
The chapter introduces the IEEE 802.3af / 802.3at PoE standard and PoE provision of the PoE Web Smart Switch.
Section 7,TROUBSHOOTING
The chapter explains how to troubleshoot the PoE Web Smart Switch.
Appendix A
The section contains cable information of the PoE Web Smart Switch.

10
1.4 Product Features
Physical Port
8-port 10/100BASE-TX RJ45 copper with PoE in-line supported (For ES2402 SERIES)
16-port 10/100BASE-TX RJ45 copper with PoE in-line supported (For ES2402 SERIES)
24-port 10/100BASE-TX RJ45 copper with PoE in-line supported (For ES2402 SERIES)
2-port 10/100/1000BASE-T RJ45 copper
2 1000BASE-X mini-GBIC/SFP slots to share with Port-17 to Port-18
Reset button for system management
Power over Ethernet
Complies with IEEE 802.3at High Power over Ethernet End-Span PSE
Complies with IEEE 802.3af Power over Ethernet End-Span PSE
Up to 8/16 IEEE 802.3at / 802.3af devices powered
Supporting PoE Power up to 30.8 watts for each PoE port
Detects powered device (PD) automatically
Circuit protection prevents power interference between ports
Remote power feeding up to 100m
PoE Power Usage LED Indicators
PoE Management
−Per port PoE function enable/disable
−PoE Port Power feeding priority
−Per PoE port power limit
−PD classification detection
−PoE Power sequential
Layer 2 Features
Auto-MDI/MDI-X detection on each RJ45 port
Preventing packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
Supporting broadcast storm control
Supporting VLAN:
- IEEE 802.1Q tag-based VLAN, out of 4095 VLAN IDs
- Port-based VLAN
- MTU VLAN (Multi-tenant Unit VLAN)
SupportsLink Aggregation
- 802.3ad Link Aggregation Control Protocol (LACP)
- Cisco ether-channel (Static Trunk)
Supports Spanning Tree Protocol
- STP, IEEE 802.1d Spanning Tree Protocol
- RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
Port mirroring to monitor the incoming or outgoing traffic on a particular port
Provides port mirror (Many-to-1)
Loopback protection to avoid broadcast loops

11
Quality of Service
2 priority queues on all switch ports
Traffic classification
- Port-based priority
- IEEE 802.1p-based priority
- IP DSCP-based priority
- TCP / UDP port-based QoS
Strict priority and Weighted Round Robin (WRR) CoS policies
Multicast
Supports IGMP Snooping v1 and v2
Security
Physical port to MAC address binding
TCP/UDP port number filter: Forwarding or discarding typical network applications
Port mirroring to monitor the incoming or outgoing traffic on a particular port
Management
Switch Management Interfaces
- Web switch management
- SNMP v1 switch management
Firmware upload/download via HTTP
Hardware reset button for system reboot or reset to factory default

12
1.5 Product Specifications
Product
ES2402
-24P-2C
Hardware Specifications
10/100Mbps Copper Ports 24 10/100BASE-TX RJ45 Auto-MDI/MDI-X ports
Gigabit Copper Ports 2 10/100/1000BASE-T RJ45 Auto-MDI/MDI-X ports
SFP/mini-GBIC Slots 2 1000BASE-X SFP interfaces, shared with Port-25 to Port-26
Switch Architecture Store-and-Forward
Switch Fabric 8.8Gbps / non-blocking
Throughput 6.54Mpps@64Bytes
Address Table 4K entries, automatic source address learning and ageing
Share Data Buffer 2.75Mb embedded memory for packet buffers
Flow Control
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
Maximum Transmit Unit 1536 Bytes
Reset Button < 5 sec: System reboot
> 5 sec: Factory Default
Dimensions (W x D x H) 440 x 300 x 44.5 mm, 1U height
Weight TBD kg
LED
System:
Power (Green)
10/100BASE-TX RJ45 Interfaces (Port1 to Port24):
10/100Mbps LNK/ACT (Green)
PoE In-Use (Orange)
10/100/1000BASE-T RJ45 / SFP Interfaces (Port25 to Port26):
LNK/ACT (Green)
100/1000 (Green)
PoE Usage LED Indicators
90W, 180W, 270W, 360W (Orange)
Cable
Twisted-Pair
10BASE-T: 2 -Pair UTP CAT. 3, 4, 5, up to 100 meters
100BASE-TX: 2-Pair UTP CAT. 5, 5e up to 100 meters
1000BASE-T: 4 -Pair UTP CAT. 5e, 6 up to 100 meters
Fiber-Optic
Cable
1000BASE-SX :
50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 550m (varying on
SFP module)
1000BASE-LX :
9/125μm single-mode fiber optic cable, up to 10/20/30/40/50/70/120 kilometers
(varying on SFP module)
Power Requirements 100~240V AC, 50/60Hz, 4A
Power Consumption Max.440 watts / 1502.68 BTU

13
ESD Protection
4KV DC
Power over Ethernet
PoE Standard
IEEE 802.3af / 802.3at PoE / PSE
PoE Power Supply Type
End-span
PoE Power Output
Per Port 54V DC, Max. 30.8 watts
Power Pin Assignment
1/2(+), 3/6(-)
PoE Power Budget 380 watts (max.)
PoE Ability
PD @ 7 watts
PD @ 15.4 watts 24 units
PD @ 30.8 watts 12 units
Layer 2 Functions
Port Configuration
Port disable / enable
Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow Control disable / enable
Port Status
Display each port’s speed duplex mode, link status, flow control status, auto
negotiation status and trunk status
Port Mirroring TX / RX / Both
Many-to-1 monitor
VLAN
802.1Q tagged-based VLAN, up to 30 VLAN groups, out of 4094 VLAN IDs
Port-based VLAN, up to 18 VLAN groups
MTU VLAN
Link Aggregation 1 group of 2-Port 10/100/1000BASE-T trunk supported
QoS Allows to assign low / high priority on each port
First-In-First-Out, All-High-before-Low, Weight-Round-Robin QoS policy
IGMP Snooping
IGMP (v1/v2) Snooping, up to 32 multicast groups
Without Query supported
Security Control MAC address binding
TCP & UDP filter
Management Functions
Basic Management Interfaces Web Browser, SNMP v1
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet over Fiber-Optic
IEEE 802.3x Full-duplex flow control
IEEE 802.1Q VLAN
IEEE 802.1p QoS
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol

14
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
Environment
Operating Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Storage
Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Product
ES2402-16P-2C
Hardware Specifications
10/100Mbps Copper Ports
16 10/100BASE-TX RJ45 Auto-MDI/MDI-X ports
Gigabit Copper Ports
2 10/100/1000BASE-T RJ45 Auto-MDI/MDI-X ports
SFP/mini-GBIC Slots
2 1000BASE-X SFP interfaces, shared with Port-17 to Port-18
Switch Architecture
Store-and-Forward
Switch Fabric
7.2Gbps / non-blocking
Throughput
5.35Mpps@64Bytes
Address Table
4K entries, automatic source address learning and ageing
Share Data Buffer
2.75Mb embedded memory for packet buffers
Flow Control IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
Jumbo Frame
1536 Bytes
Reset Button < 5 sec: System reboot
> 5 sec: Factory Default
Dimensions (W x D x H)
440 x 200 x 44.5 mm, 1U height
Weight
2.55kg
LED
System:
Power (Green)
10/100BASE-TX RJ45 Interfaces (Port1 to Port16):
10/100Mbps LNK/ACT (Green)
PoE In-Use (Orange)
10/100/1000BASE-T RJ45 / SFP Interfaces (Port17 to Port18):
LNK/ACT (Green)
100/1000 (Green)
PoE Usage LED Indicators
50W, 100W, 150W, 190W (Orange)
Power Requirements
100~240V AC, 50/60Hz, 4A
Power Consumption
Max. 240 watts / 816 BTU
ESD Protection
4KV DC
Power over Ethernet
PoE Standard
IEEE 802.3af / 802.3at PoE/PSE

15
PoE Power Supply Type
End-span
PoE Power Output
Per Port 52V DC, Max. 30.8 watts
Power Pin Assignment
1/2(+), 3/6(-)
PoE Power Budget
220 watts (max.)
PoE
Ability
PD @ 7 watts
16 units
PD @ 15.4 watts
14 units
PD @ 30.8 watts
7 units
Layer 2 Functions
Port Configuration
Port disable / enable
Auto-negotiation 10/100Mbps and 10/100/1000Mbpsfull and half duplex mode
selection
Flow Control
Port Status TX / RX / Both
Many-to-1 monitor
Port Mirroring
802.1Q tagged-based VLAN, out of 4094 VLAN IDs
Port-based VLAN
MTU VLAN
VLAN STP/RSTP
Loopback Detection
Link Aggregation
1 group of 2-Port 10/100/1000BASE-T trunk supported
QoS
First-In-First-Out
All-High-before-Low
Weight-Round-Robin QoS policy
DSCP field in IP Packet
IGMP Snooping IGMP Snooping v1 and v2
Security Control MAC address binding
TCP & UDP filter
Management Functions
Basic Management Interfaces
Web Browser, SNMP v1
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet
IEEE 802.3x Full-duplex flow control
IEEE 802.1Q VLAN
IEEE 802.1p QoS
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus

16
Cable
Twisted-Pair
10BASE-T: 2 -Pair UTP CAT. 3, 4, 5, up to 100 meters
100BASE-TX: 2-Pair UTP CAT. 5, 5e up to 100 meters
1000BASE-T: 4 -Pair UTP CAT. 5e, 6 up to 100 meters
Fiber-Optic
Cable
1000BASE-SX :
50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 550m (varying on
SFP module)
1000BASE-LX :
9/125μm single-mode fiber optic cable, up to 10/20/30/40/50/70/120 kilometers
(varying on SFP module)
Environment
Operating Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)
Storage Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)
Product
ES2402-8P-2C
Hardware Specifications
10/100Mbps Copper Ports
8 10/100BASE-TX RJ45 Auto-MDI/MDI-X ports
Gigabit Copper Ports
2 10/100/1000BASE-T RJ45 Auto-MDI/MDI-X ports
SFP/mini-GBIC Slots
2 1000BASE-X SFP interfaces, shared with Port-9 to Port-10
Switch Architecture
Store-and-Forward
Switch Fabric
5.6Gbps / non-blocking
Throughput
4.16Mpps@64Bytes
Address Table
4K entries, automatic source address learning and ageing
Share Data Buffer
2.75Mb embedded memory for packet buffers
Flow Control IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
Jumbo Frame
1536 Bytes
Reset Button < 5 sec: System reboot
> 5 sec: Factory Default
Dimensions (W x D x H)
330 x 153 x 44.5 mm, 1U height
Weight
1.6kg
LED
System:
Power (Green)
10/100BASE-TX RJ45 Interfaces (Port1 to Port8):
10/100Mbps LNK/ACT (Green)
PoE In-Use (Orange)
10/100/1000BASE-T RJ45 / SFP Interfaces (Port9 to Port10):
LNK/ACT (Green)
100/1000 (Green)
PoE Usage LED Indicators
30W, 60W, 90W, 120W (Orange)
Power Requirements
100~240V AC, 50/60Hz, 2A

17
Power Consumption
Max. 140 watts / 480 BTU
ESD Protection
4KV DC
Power over Ethernet
PoE Standard
IEEE 802.3af / 802.3at PoE / PSE
PoE Power Supply Type
End-span
PoE Power Output
Per Port 52V DC, Max. 30.8 watts
Power Pin Assignment
1/2(+), 3/6(-)
PoE Power Budget
125 watts (max.)
PoE
Ability
PD @ 7 watts
8 units
PD @ 15.4 watts
8 units
PD @ 30.8 watts
4 units
Layer 2 Functions
Port Configuration
Port disable / enable
Auto-negotiation 10/100Mbps and 10/100/1000Mbpsfull and half duplex mode
selection
Flow Control
Port Mirroring TX / RX / Both
Many-to-1 monitor
VLAN
802.1Q tagged-based VLAN, out of 4094 VLAN IDs
Port-based VLAN
MTU VLAN
Spanning Tree STP/RSTP
Loopback Detection
Link Aggregation
1 group of 2-Port 10/100/1000BASE-T trunk supported
QoS
First-In-First-Out
All-High-before-Low
Weight-Round-Robin
DSCP field in IP Packet
IGMP Snooping IGMP Snooping v1 and v2
Fast Leave
Security Control MAC address binding
TCP & UDP filter
Management Functions
Basic Management Interfaces
Web Browser, SNMP v1
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet
IEEE 802.3x Full-duplex flow control
IEEE 802.1Q VLAN
IEEE 802.1p QoS
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.3af Power over Ethernet

18
IEEE 802.3at Power over Ethernet Plus
Cable
Twisted-Pair
10BASE-T: 2 -Pair UTP CAT. 3, 4, 5, up to 100 meters
100BASE-TX: 2-Pair UTP CAT. 5, 5e up to 100 meters
1000BASE-T: 4 -Pair UTP CAT. 5e, 6 up to 100 meters
Fiber-Optic
Cable
1000BASE-SX :
50/125μm or 62.5/125μm multi-mode fiber optic cable, up to 550m (varying on
SFP module)
1000BASE-LX :
9/125μm single-mode fiber optic cable, up to 10/20/30/40/50/70/120 kilometers
(varying on SFP module)
Environment
Operating Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)
Storage Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)
2. INSTALLATION
This section describes the hardware features and installation of the PoE Web Smart Switch on the desktop or rack mount. For
easier management and control of the PoE Web Smart Switch, familiarize yourself with its display indicators, and ports. Front
panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the PoE Web Smart
Switch, please read this chapter completely.
2.1 Hardware Description
2.1.1 Switch Front Panel
The front panel provides a simple interface monitoring the PoE Web Smart Switch. Figure 2-1 shows the front panel of the
ES2402 SERIES.
ES2402-24P-2C Front Panel
ES2402-16P-2C Front Panel
ES2402-8P-2C Front Panel

19
Figure 2-1 ES2402 SERIES front panel
■Fast Ethernet TP interface
10/100BASE-TX Copper, RJ45 Twist-Pair: Up to 100 meters.
■Gigabit TP Interface
10/100/1000BASE-T Copper, RJ45 Twist-Pair: up to 100 meters.
■Gigabit SFP Slots
1000BASE-SX/LX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver module: From 550 meters (Multi-mode fiber),
up to 10/20/30/50/60/70 kilometers (Single-mode fiber).
■Reset Button
On the left side of the front panel, the reset button is designed for rebooting the PoE Web Smart Switch without turning off
and on the power. The following is the summary table of Reset button functions:
Reset Button Pressed and Released
Function
< 5 sec
: System Reboot Reboot the PoE Web Smart Switch.
> 5 sec: Factory Default
Reset the PoE Web Smart Switch to Factory Default
configuration. The PoE Web Smart Switch will then reboot
and load the default settings as shown below:
Default Username: admin
Default Password: admin
Default IP address: 192.168.0.100
Subnet mask: 255.255.255.0

Default Gateway: 192.168.0.254
2.1.2 LED Indications
Front panel LED indicating is instant status of port links, data activity and system power, and help monitor and troubleshoot
when needed. Figure 2-2 shows the LED indications of these PoE Web Smart Switches.
ES2402 SERIES LED Indication

20
Figure 2-2 ES2402 SERIES LED panels
System
LED
Color
Function
PWR Green Lights to indicate that the Switch has power.
Per 10/100Mbps port with PoE interfaces
LED Color Function
LNK/ACT Green Lights:Indicates the link through that port is successfully established at 10/100Mbps.
Blink:
Indicates that the Switch is actively sending or receiving data over that port.
PoE In-Use Orange Lights: Indicates the port is providing 56V DC in-line power.
Off:
Indicates the connected device is not a PoE Powered Device (PD).
Per 10/100/1000Mbps RJ45 Combo Interface
LED Color Function
LNK/ACT Green Blink: Indicates that the Switch is actively sending or receiving data over that port.
100/1000 Green
Lights. Indicates the port is successfully established at 1000Mbps.
Slow
Blink:
Indicates the port is successfully established at 100Mbps.
OFF:Indicates the port is successfully established at 10Mbps.
Per 1000Mbps SFP Combo Interface
LED Color Function
LNK/ACT Green Blink: Indicates that the Switch is actively sending or receiving data over that port.
1000 Green Lights. Indicates the port is successfully established at 1000Mbps.
PoE Usage
LED Color Function
ES2402-24P-2C
90 Orange Lights to indicate the PoE power consumption has equal 90W or over 90W
180 Orange Lights to indicate the PoE power consumption has equal 180W or over 180W
270 Orange Lights to indicate the PoE power consumption has equal 270W or over 270W