Interlogix NS3500-24T-4C Installation instructions

NS3500-24T-4C Managed
Switch Command Guide
P/N 1073459-EN • REV A • ISS 06MAR18

Copyright
©
2018 United Technologies Corporation.
Interlogix is part of UTC
Climate, Controls & Security, a unit of United Technologies
Corporation
. All rights reserved.
Trademarks and patents
Trade names used in this document may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Manufacturer
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626
-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Version
This document applies to
NS3500-24T-4C.
FCC compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful
interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC compliance
Class A:
This equipment has been tested and found to comply with the limits for a Class
A digital device, p
ursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy
and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be requi
red to correct the interference at his own expense.
Canada
This Class A digital apparatus complies with CAN ICES
-003 (A)/NMB-3 (A).
Cet appareil numérique de la classe A est conforme à la norme CAN ICES
-003
(A)/NMB
-3 (A).
ACMA compliance
Notice!
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
Certification
EU directives
This product and
- if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19
/EU (WEEE directive): Products marked with this symbol cannot be disposed
of
as unsorted municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see:
www.recyclethi
s.info.
Product warnings and
disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE TO AND INSTALLATION BY
QUALIFIED PROFESSIONALS. UTC FIRE & SECURITY CANNOT PROVIDE ANY
ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS PRODUCTS,
INCLUDING ANY “AUTHORIZED
DEALER” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL FIRE AND
SECURITY RELATED PRODUCTS
.
For more information on warranty disclaimers and product safety information, please
check
www.firesecurityproducts.com/policy/product-warning/ or scan the QR code:
Contact information and
manuals
For contact information go to:
www.interlogix.com or www.firesecurityproducts.com.
To get translations for this and other product manuals go to:
www.firesecurityproducts.com
.

Content
Chapter 1 Command line interface 2
Accessing the CLI 2
Command line modes 2
Requirements 4
Chapter 2 Console CLI management 5
Terminal setup 5
Log on to the console 6
Configuring the IP address 7
Chapter 3 Telnet CLI management 10
Telnet login 10
Chapter 4 Commands for CLI configuration 11
clear 11
configure terminal 29
copy 241
debug 241
delete 242
dir 242
disable 243
do 243
dot1x 244
enable 244
erps 245
exit 245
firmware 246
ip 247
logout 247
more 248
no 248
ping 249
reload 250
send 251
show 252
terminal 322
NS3500-24T-4C Managed Switch Command Guide 1

Chapter 1
Command line interface
Accessing the CLI
When accessing the management interface for the switch over a direct connection to
the server’s console port or via a Telnet connection, the switch can be managed by
entering command keywords and parameters at the prompt. Using the switch's
command-line interface (CLI) is very similar to entering commands on a UNIX system.
This chapter describes how to use the Command Line Interface (CLI).
Command line modes
The CLI groups all the commands in appropriate modes according to the nature of the
command. A sample of the CLI command modes are described below. Each of the
command modes supports specific software commands.
Mode-based command hierarchy
The Command Line Interface (CLI) groups all the commands in appropriate modes by
the nature of the commands. Examples of the CLI command modes are described
below. Each of the command modes supports specific switch commands.
The CLI Command Modes table captures the command modes, the prompts visible in
that mode, and the exit method from that mode.
Command Mode
Access Method Prompt Exit or Access Previous
Mode
User mode
This is the first level of
access. Perform basic
tasks and list system
information.
COMMAND> Enter Logout command
Priveleged mode
From the User Mode, enter
the enable command. Switch# To exit to the User Mode, enter exit or Logout.
Global
config mode From the Privileged Mode,
enter the configuration
command.
Switch (Config)# To exit to the Privileged
Mode, enter the exit
command.
2 NS3500-24T-4C Managed Switch Command Guide

Chapter 1: Command line interface
Command Mode
Access Method Prompt Exit or Access Previous
Mode
Interface config mode
From the Global Config
mode, enter the interface
<port#> command.
Switch (interface
<port#>)# To exit to the Global Config mode, enter exit.
The CLI is divided into various modes. The commands in one mode are not available
until the operator switches to that particular mode. The commands available to the
operator at any point in time depend upon the mode. Entering a question mark (?) at
the CLI prompt displays a list of the available commands and descriptions of the
commands.
The CLI provides the following modes:
User mode
When the operator logs into the CLI, the User Mode is the initial mode. The User Mode
contains a limited set of commands. The command prompt shown at this level is:
Command Prompt: switch>
Privileged mode
To have access to the full suite of commands, the operator must enter the Privileged
Mode. The Privileged Mode requires password authentication. From Privileged Mode,
the operator can issue any Exec command to enter the Global Configuration mode. The
command prompt shown at this level is:
Command Prompt: switch#
Global config mode
This mode permits the operator to make modifications to the running configuration.
General setup commands are grouped in this mode. From the Global Configuration
mode, the operator can enter the Interface Configuration mode. The command prompt
at this level is:
Command prompt: switch(Config)#
From the Global Config mode, the operator may enter the following configuration
modes:
Interface config mode
Many features are enabled for a particular interface. The Interface commands enable or
modify the operation of an interface. In this mode, a physical port is set up for a specific
logical connection operation. The command prompt at this level is:
Command prompt: Switch(Interface <port#>)#
NS3500-24T-4C Managed Switch Command Guide 3

Chapter 1: Command line interface
Requirements
• Workstations running Windows XP/Vista/7/8/10, Windows 2003/2008, MAC OS X or
later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols.
• Workstations are installed with Ethernet NIC (Network Interface Card).
• Serial Port Connection (Terminal)
• The above Workstations come with COM Port (DB9) or USB-to-RS-232
converter.
• The above Workstations have been installed with terminal emulator, such as
Hyper Terminal included in Windows XP/2003.
• Serial cable -- one end is attached to the RS-232 serial port, while the other end
to the console port of the Managed Switch.
• Ethernet Port Connection
• Network cables -- Use standard network (UTP) cables with RJ-45 connectors.
• The above PC is installed with Web Browser and JAVA runtime environment
plug-in.
4 NS3500-24T-4C Managed Switch Command Guide

Chapter 2
Console CLI management
Terminal setup
To configure the system, connect a serial cable to a COM port on a PC or notebook
computer and to a RS232 type of serial port on the managed switch.
A terminal program is required to make the software connection to the managed switch.
Windows' Hyper Terminal program may be a good choice. The Hyper Terminal can be
accessed from the Start menu.
1. Click Start > Programs > Accessories, and then click Hyper Terminal.
2. When the following screen appears, make sure that the COM port is configured as
shown:
5 NS3500-24T-4C Managed Switch Command Guide

Chapter 2: Console CLI management
If required, you can change these settings after logging on. This management method
is often preferred because you can remain connected and monitor the system during
system reboots. Also, certain error messages are sent to the serial port, regardless of
the interface through which the associated action was initiated. A Macintosh or PC
attachment can use any terminal-emulation program for connecting to the terminal
serial port. A workstation attachment under UNIX can use an emulator such as TIP.
Log on to the console
Once the terminal is connected to the device, power on the managed switch, and the
terminal will display “running testing procedures”. Then, the following message asks to
log-in user name and password. The factory default user name and password are
shown as follows and the login screen appears.
Username: admin
Password: admin
6 NS3500-24T-4C Managed Switch Command Guide

Chapter 2: Console CLI management
The user can now enter commands to manage the managed switch. For a detailed
description of the commands, refer to the following chapters.
Note:
1. For security purposes, change and memorize the new password after this first
setup.
2. Only accept commands in lowercase letters under the console interface.
Configuring the IP address
The Managed Switch is shipped with the default IP address shown below.
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the switch, follow these
procedures:
Show the current IP address
At the “#” prompt, enter “show ip interface brief”. The screen displays the current IP
address and Subnet Mask as shown:
NS3500-24T-4C Managed Switch Command Guide 7

Chapter 2: Console CLI management
Configure the IP address
At the “#” prompt, enter the following command and press Enter.
#configure terminal
(config)# interface vlan 1
(config-if-vlan)# ip address 192.168.1.100 255.255.255.0
The previous command would apply the following settings for the managed switch.
IP Address:192.168.1.100
Subnet Mask: 255.255.255.0
At the “#” prompt, enter “show ip interface brief” to check if the IP address has
changed.
8 NS3500-24T-4C Managed Switch Command Guide

Chapter 2: Console CLI management
Store the current switch configuration
At the “#” prompt, enter the following command and press Enter.
# copy running-config startup-config
If the IP is successfully configured, the managed switch will apply the new IP address
setting immediately. You can access the web interface of the managed switch through
the new IP address.
Note: If you are not familiar with the console command or the related parameter, enter “
?” at any time in the console to get the help description.
.
NS3500-24T-4C Managed Switch Command Guide 9

Chapter 3
Telnet CLI management
Telnet login
The managed switch also supports telnet for remote management. The switch asks for
a user name and password for remote login when using telnet. Use “admin” for the
both the username and password.
Default IP address: 192.168.0.100
Username: admin
Password: admin
NS3500-24T-4C Managed Switch Command Guide 10

Chapter 4
Commands for CLI
configuration
clear
clear access management statistics
Command:
clear access management statistics
Default:
N/A
Usage Guide:
To clear the access management statistics.
Example:
To clear the Switch’s access management statistics.
Switch# clear access management statistics
clear access-list ace statistics
Command:
clear access-list ace statistics
Default:
N/A
Usage Guide:
To clear the Access list entry statistics.
Example:
To clear the Switch’s Access list entry statistics.
Switch# clear access-list ace statistics
NS3500-24T-4C Managed Switch Command Guide 11

Chapter 4: Commands for CLI configuration
clear dot1x statistics interface
Command:
clear dot1x statistics interface GigabitEthernet |
10GigabitEthernet
Default:
N/A
Usage Guide:
To clear the dot1x statistics.
Example:
To clear the Switch’s GigabitEthernet 1/25 dot1x statistics.
Switch# clear dot1x statistics interface GigabitEthernet 1/25
clear eps
Command:
clear eps <Inst : uint>
<Inst : uint> The EPS instance number.
Default:
N/A
Usage Guide:
To clear the EPS instance number.
clear erps
Command:
clear erps < ERPS group numbers > statistics
Default:
N/A
Usage Guide:
To clear the ERPS group numbers statistics.
Example:
To clear the Switch’s ERPS group 1 statistics.
Switch# # clear erps 1 statistics
clear erps statistics
Command:
clear erps statistics
12 NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration
Default:
N/A
Usage Guide:
To clear the ERPS statistics.
Example:
To clear the Switch’s ERPS statistics.
Switch# clear erps statistics
clear evc statistics
Command:
clear evc statistics
Default:
N/A
Usage Guide:
To clear the Ethernet Virtual Connections statistics.
Example:
To clear the Switch’s Ethernet Virtual Connections statistics.
Switch# clear evc statistics
clear ip arp
Command:
clear ip arp
Default:
N/A
Usage Guide:
To clear the ARP cache.
Example:
To clear the Switch’s ARP cache.
Switch# clear ip arp
clear ip dhcp detailed statistics all
Command:
clear ip dhcp detailed statistics all
Default:
N/A
Usage Guide:
NS3500-24T-4C Managed Switch Command Guide 13

Chapter 4: Commands for CLI configuration
To clear the DHCP detailed statistics for all.
Example:
To clear the Switch’s DHCP detailed statistics for all.
Switch# clear ip dhcp detailed statistics all
clear ip dhcp detailed statistics client
Command:
clear ip dhcp detailed statistics client
Default:
N/A
Usage Guide:
To clear the DHCP client statistics.
Example:
To clear the Switch’s DHCP client statistics.
Switch# clear ip dhcp detailed statistics client
clear ip dhcp detailed statistics helper
Command:
clear ip dhcp detailed statistics helper
Default:
N/A
Usage Guide:
To clear the DHCP normal L2 or L3 forward statistics.
Example:
To clear the Switch’s DHCP normal L2 or L3 forward statistics.
Switch# clear ip dhcp detailed statistics helper
clear ip dhcp detailed statistics server
Command:
clear ip dhcp detailed statistics server
Default:
N/A
Usage Guide:
To clear the DHCP server statistics.
Example:
To clear the Switch’s DHCP server statistics.
14 NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration
Switch# clear ip dhcp detailed statistics server
clear ip dhcp detailed statistics snooping
Command:
clear ip dhcp detailed statistics snooping
Default:
N/A
Usage Guide:
To clear the DHCP snooping statistics.
Example:
To clear the Switch’s DHCP normal L2 or L3 forward statistics.
Switch# clear ip dhcp detailed statistics snooping
clear ip dhcp relay statistics
Command:
clear ip dhcp relay statistics
Default:
N/A
Usage Guide:
To clear the DHCP relay statistics.
Example:
To clear the Switch’s DHCP relay statistics.
Switch# clear ip dhcp relay statistics
clear ip dhcp server binding
Command:
clear ip dhcp server binding <IP>
<IP> A.B.C.D
Default:
N/A
Usage Guide:
To clear the DHCP server binding cache.
Example:
To clear the Switch’s DHCP server(192.168.0.100) binding cache.
NS3500-24T-4C Managed Switch Command Guide 15

Chapter 4: Commands for CLI configuration
Switch# clear ip dhcp server binding 192.168.0.100
clear ip dhcp server binding automatic
Command:
clear ip dhcp server binding automatic
Default:
N/A
Usage Guide:
To clear the DHCP automatic bindings cache.
Example:
To clear the Switch’s DHCP automatic bindings cache.
Switch# clear ip dhcp server binding automatic
clear ip dhcp server binding expired
Command:
clear ip dhcp server binding expired
Default:
N/A
Usage Guide:
To clear the DHCP expired bindings for free.
Example:
To clear the Switch’s DHCP expired bindings for free.
Switch# clear ip dhcp server binding expired
clear ip dhcp server binding manual
Command:
clear ip dhcp server binding manual
Default:
N/A
Usage Guide:
To clear the DHCP server manual binding cache.
Example:
To clear the Switch’s DHCP server manual binding cache.
Switch# clear ip dhcp server binding manual
16 NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration
clear ip igmp snooping statistics
Command:
clear ip igmp snooping statistics
Default:
N/A
Usage Guide:
To clear the IGMP snooping statistics.
Example:
To clear the Switch’s IGMP snooping statistics.
Switch# clear ip igmp snooping statistics
clear ip igmp snooping vlan
Command:
clear ip igmp snooping vlan < vlan_list> statistics
<vlan_list> VLAN identifier(s): VID
Default:
N/A
Usage Guide:
To clear the IGMP snooping vlan < vlan_list> statistics.
Example:
To clear the Switch’s IGMP snooping vlan 1 statistics.
Switch# clear ip igmp snooping vlan 1 statistics
clear ip statistics icmp icmp-msg
Command:
clear ip statistics icmp icmp-msg <Type : 0~255>
<Type : 0~255> ICMP message type ranges from 0 to 255
Default:
N/A
Usage Guide:
To clear the IPv4 ICMP traffic for designated message type.
Example:
To clear the Switch’s IPv4 ICMP traffic for designated message type 0.
Switch# clear ip statistics icmp icmp-msg 0
NS3500-24T-4C Managed Switch Command Guide 17

Chapter 4: Commands for CLI configuration
clear ip statistics icmp interface vlan
Command:
clear ip statistics icmp interface vlan <vlan_list>
<vlan_list> VLAN identifier(s): VID
Default:
N/A
Usage Guide:
To clear the IPv4 interface/ICMP statistics for specific VLAN.
Example:
To clear the Switch’s IP interface/ICMP statistics for specific VLAN 1.
Switch# clear ip statistics icmp interface vlan 1
clear ip statistics system icmp icmp-msg
Command:
clear ip statistics system icmp icmp-msg <Type : 0~255>
<Type : 0~255> ICMP message type ranges from 0 to 255
Default:
N/A
Usage Guide:
To clear the IPv4 ICMP statistics for specific ICMP message type.
Example:
To clear the Switch’s IPv4 ICMP statistics for specific ICMP message type 0.
Switch# clear ip statistics system icmp icmp-msg 0
clear ip statistics system icmp interface vlan
Command:
clear ip statistics system icmp interface vlan
<vlan_list> VLAN identifier(s): VID
Default:
N/A
Usage Guide:
To clear the IPv4 ICMP interface statistics for specific VLAN.
Example:
To clear the Switch’s IPv4 ICMP interface statistics for specific VLAN 1.
Switch# clear ip statistics system icmp interface vlan 1
18 NS3500-24T-4C Managed Switch Command Guide