Interlogix TVD-LWB-1 User manual

© 2016 United Technologies Corporation. P/N 1072896-EN • REV F • ISS 16NOV16
Interlogix is part of UTC Climate, Controls and Security, a unit of United Technologies Corporation. All rights reserved.
TVD-LWB-1 L-shaped Wall Bracket Installation
Instructions
Description
Figure 1: Physical descriptions
D
imensions: 155.5 × 90 × 111 mm (6.12 × 3.54 × 4.37 in.)
Weight
: 278.7 g (0.61 lb.)
Accessories:
Screw A M4 x 6 mm (4 pcs)
(Used to attach the wedge camera to the bracket)
Screw B 4 x 25 mm (4 pcs )
(Used to attach bracket to the wall)
Screw C M4 x 8 mm (3 pcs)
(Used to attach the plastic dome camera to the
bracket)
Drywall anchor
6 x 29 mm (4 pcs )
List of SKUs by hole position
Hole
A TruVision IP plastic dome:
NTSC: TVD-3105, TVD-3106
PAL: TVD-1105, TVD-1106
TruVision IP indoor plastic dome:
NTSC: TVD-3101, TVD-3102
PAL: TVD-1101, TVD-1102
TruVision HD-TVI plastic dome:
NTSC: TVD-4401, TVD-4403
PAL: TVD-2401, TVD-2403
TruVision IP S3 fixed lens dome:
TVD-5301, TVD-5302
Hole
B TruVision IP wedge camera with adapter:
NTSC: TVD-N210W-4-N, TVD-M1210W-2-N,
TVD-M1210W-2W-N, TVD-M2210W-4-N, TVW-3101,
TVW-3102, TVW-3107, TVW-3108, TVW-3109,
PAL: TVD-N210W-4-P, TVD-M1210W-2-P,
TVD-M1210W-2W-P, TVD-M2210W-4-P, TVW-1101,
TVW-1102, TVW-1107, TVW-1108, TVW-1109
TruVision Wi-Fi IP wedge camera with adapter:
NTSC: TVW-3103, TVW-3104, TVW-3105, TVW-3106，
TVW-3116
PAL: TVW-1103, TVW-1104, TVW-1105, TVW-1106,
TVW-1116
TruVision Panoramic Wi-Fi IP Wedge camera with
adapter:
NTSC: TVW-3130
PAL: TVW-1130
TruVision analog wedge camera with adapter:
NTSC: TVW-4101
PAL: TVW-2101
TruVision IP S3 wedge camera with adapter:
TVW-5301, TVW-5302, TVW-5303, TVW-5304, TVW-
5305
TruVision HD-TVI wedge camera with adapter:
NTSC: TVW-4401
PAL: TVW-2401
8.0 mm

2 / 2 P/N 1072896-EN • REV F • ISS 16NOV16
Installation
To attach a plastic dome to a TVD-LWB-1 bracket:
Note: See the list of SKUs by hole position on page 1, Hole A.
1. Attach the bracket to the wall using the four B screws
(drywall anchors are provided, if needed).
2. Remove the bubble assembly and attach the dome to the
bracket using three C screws into holes labeled A (see
Figure 1 for the location of the holes).
3. Finish cabling and adjust the lens position, then attach the
bubble assembly to the camera.
To attach a wedge camera to a TVD-LWB-1 bracket:
Note: See the list of SKUs by hole position on page 1, Hole B.
1. Attach the bracket to the wall by using the four B screws
(drywall anchors are provided, if needed).
2. Attach the adaptor plate to the TVD-LWB-1 bracket using
the four A screws into holes B (see the Figure 1 on page 1
for the location of the holes).
3. Remove the bubble assembly and attach the camera to
the adaptor plate with two screws (included with the
camera).
4. Finish cabling and adjust the lens position, then re-attach
the bubble assembly to the camera.
Legal information
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Trademarks and
patents
The trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Certification
Contact information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.