Intermatic Intouch ca600 User manual

WARNING: Read instructions completely before installation and retain for future reference.

WARNING:

CAUTION:

CAUTION

OTHER CAUTIONS:

For installation and/or use in accordance with appropriate electrical codes and regulations.

Consult a qualified electrician for installation and operation.

To avoid overheating and possible damage to this device and connected equipment, do not

attempt to control a receptacle, fluorescent lighting, motor, or transformer.

(For Incandescent Only): USE WITH INCANDESCENT OR 120V HALOGEN FIXTURES ONLY.

1. Use only one (1) dimmer per load. For remote operation, use standard 3-way or 4-way electrical devices for

ON/OFF operation or use with Z-Wave compatible control for wireless control from any location.

2. Use Air-Gap switch to disconnect power when servicing or changing lamp.

3. Use this device only with 75°C rated copper or copper clad wire.

Model CA600

Single-Pole / Multi-Pole

Dimmer600 Watt Switch

Specifications:

Ratings:

Colors:

Connections:

RF Information:

Network Information:

Single-Pole (One Location)

or 3-Way (Multi-Location)

or Wireless RF Control

120VAC, 50/60Hz

Maximum Wattage: 600W

Minimum Wattage: 40W

Includes white, ivory, and light almond

snap-on rocker plates.

Black-Line, Blue-Load, Red-Traveler,

Green-Ground

Minimum Range:

50ft indoor; 100ft outdoor

Frequency: 908.42 MHz

Mesh Network - Each line powered

node acts as a repeater to route

distant signals.

Data Rate: 9600 bits/second

Size: 232 Z-Wave™ Nodes

Operating Temperature Range:

32°F (0°C) to 104°F (40°C)

Power Consumption: 2.0W Max

Fade-on& Fade-off

1% Dimming (100 Increments)

Dimming:

INSTALLATION:

1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND

TEST THAT POWER IS OFF BEFORE WIRING.

Operation:

2. For retrofit applications, remove wall plate and disconnect light switch.

3. Refer to wiring diagrams for proper connection of dimmer for intended application.

4. Check that all wire connections are secure.

5. Place all wires inside junction box. Install dimmer using (2) mounting screws furnished. Complete

installation with a decorator style wall-plate.

6. Reconnect your electrical power.

7. Tap top of rocker to turn lights on; tap bottom of rocker to turn lights off; press and hold top of

rocker to brighten connected load; press and hold bottom of rocker to dim connected load.

8. For programming instructions refer to the (158CA12789).InTouch Installer & Users Guide

The CA600 In-Wall Dimmer is a Z-wave™ enabled device which is fully compatible with any Z-wave enabled

network. Z-wave enabled devices display the Z-wave logo and guarantee connectivity and interoperability

between devices. Each line powered node in a Z-wave network is designed to act as a repeater forming a

mesh network eliminating radio “dead spots” and providing the highest level of reliability.

- Multiple location dimming when used with wireless accessory controls.

- Multiple location On/Off control using conventional 3-way or 4-way wiring and devices.

- Lights fade up or down turned on or off.

- Automatically returns to last level in the event of power fluctuations.

- Light levels can be set by pressing and holding the rocker until the desired light level is reached.

- Mini-scenes allows local control of connected load plus up to 5 additional Z-wave devices.

- Full 230 device scene control when used with Intermatic InTouch™ server .

- Dimmer always operates local load, does not require central control system.

Features

On/Off and

(CA5500B)

This product is compatible with other Z-Wave enabled products™

Rocker Color Conversion

The frame and rocker color of this device can be converted to

match interior design requirements. Simply use one of the

included color plates (white, ivory, or light almond) and proceed

as follows (please note that the device must be removed from

the junction box to change the rocker, follow the installation

instructions and warnings).

1. Select the color of the face you desire.

2. The frame has snaps on its sides. Using a small screwdriver

or thumbnail, gently remove the frame and rocker from the

housing body.

3. Take the new frame and position it properly to the housing

body. Notice that the locking snaps will align in only the proper

direction. Line up the plastic snaps with the slots in the housing

body and snap into place.

4. The frame snaps in with an audible click. Ensure that both

snaps are secure. Replace the device in the junction box

following installation instructions.

The color conversion is complete.

Rocker

Frame

Snap

FCC STATEMENT OF COMPLIANCE

WARNING! Changes or modifications not expressly approved by Intermatic Inc. could void the user’s authority to operate the

equipment.

This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna or device.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Note: Air-Gap switch should be used to remove

power from connected loads before servicing.

Providing a Brighter Solution™

158CA12471REF

WIRELESS CONTROLS

Single Pole Application

Hot Black

Neutral

Blue

Incandescent

Lighting Load

Red

Wire Connector Ground

Green

120VAC

50/60 Hz

3-Way Application

Hot Black

Neutral

Blue

Incandescent

Lighting Load

Red

Wire Connector Ground

120VAC

50/60 Hz

Jumper

CA600 CA600 CA-3PS / Standard 3-Way Switch

Multi-Way Application

Hot Black

Neutral

Blue

Incandescent

Lighting Load

Red

Wire Connector Ground

120VAC

50/60 Hz

CA600 CA-3PS / Standard 3-Way SwitchCA-4PS / Standard 4-Way SwitchCA-3PS / Standard 3-Way Switch CA-4PS / Standard 4-Way Switch

Green

This product is compatible with other Z-Wave enabled products™

LIMITED TEN YEAR WARRANTY

If within ten (10) years from date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace, at its

sole option. This warranty applies only to the original purchaser and is not transferable. This warranty excludes and this is disclaimed liability for labor for

removal of this product or reinstallation. The warranty does not apply to: (a) damage caused by accident, abuse, mishandling, dropping, acts of God, or any

negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart, or otherwise modified; (c) units not used in accordance with

directions; (d) damages exceeding the cost of the product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you.

This warranty gives you specific legal rights and you may have other rights that vary from state to state.

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing postage prepaid to the

nearest authorized service center listed. Please be sure to wrap the product securely when mailing to avoid shipping damage. This warranty is made by:

Intermatic Incorporated, After Sales Service, 7777 Winn Road, Spring Grove, IL 60081-9698, 815-675-7000 www.intermatic.com

INTERMATIC INCORPORATED WILL NOT BE

LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES.

ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR

PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS

THE WARRANTY PERIOD STATED ABOVE.