Intermec Trakker Antares 2415 User manual

TE 2000t
Installation
Instructions

2 TE 2000  Installation Instructions
Note: TE 2000tterminal emulation can be used as a custom application
on Trakker Antares terminals. When you upgrade the firmware, you re-
move existing applications and files on the terminal and restore the default
configuration. Back up your custom files and applications, such as TE
2000, dcBrowser, and ROM-DOS, before doing an upgrade. This ensures
you can reinstall these applications after completing the upgrade. See
Chapter 2, “Configuring the Terminals,” in the Trakker Antares 2400 Fami-
ly System Manual (P/N: 071389) for more information.
These instructions tell you how to upgrade your terminal with Trakker
AntaresRfirmware (if necessary) and install TE 2000 on your terminal.
TE 2000 is compatible with firmware version 5.13 or greater.
SIf you are using a 2415, or 2435A Terminal,
you do not need to upgrade the firmware. Go to Step 3 on the next
page.
SIf you are using a 2425, 2455, 2475, or 248X Terminal,
press )yT2M(2425) or );248(2455, 2475, or
248X), or scan this bar code:
*../M.*
*..-.*
From the Main Menu, choose About TRAKKER 2400.Ifyouhave
firmware version 5.13 or greater, you do not need to upgrade the firm-
ware.GotoStep3onthenextpage.
2415, 2425, 2435A, 2455, 2475, or 248X Terminals
1Note the values of these parameters on your terminal, if applicable:
STerminal IP address
S(DCS 300/UDP Plus) Controller IP address
S(Host/TCP/IP) Host IP address
S(DCS 300 or host on different subnetwork) Subnet mask and default
router IP address
S(2.4 GHz OpenAir radio) Domain (also called LAN ID) and Security
ID settings for the 21XX Universal Access Pointtproduct, 011X
Access Point, or 6710 Access Point
S(2.4 GHz IEEE 802.11 DS radio) Network name for the 21XX Uni-
versal Access Point
SKeypad type setting. Use these defaults for each terminal listed:
S2415, 2425: Terminal Emulation
S2435A Hardware Defaults
S2455: VT/ANSI
S2475, 248X: IBM 5250

3TE 2000  Installation Instructions
SIf you install the firmware using the DOS firmware upgrade utility
on your personal computer, the installation will restore the terminal’s
default configuration. You will need to reenter these parameters. (You
will not need to reenter the keypad type.)
SIf you install the firmware using the Firmware Upgrade Utility on the
DCS 300, the installation will keep the current configuration.
2Install version 5.13 or greater of the firmware on the 2425, 2455, or
248X Terminal.
If you are installing the firmware using the DOS firmware upgrade util-
ity, see Chapter 2, “Configuring the Terminals,” in the Trakker Antares
2400 Family System Manual (P/N: 071389) for more information.
If you are installing the firmware using the Firmware Upgrade Utility
on the DCS 300, see “Using the DCS 300 to Upgrade TRAKKER Antares
Terminals” in your DCS 300 System Manual (P/N: 067296).
3Create a directory on your personal computer (PC). Copy the files from
the TE 2000 upgrade CD to the new directory. At the DOS prompt,
change to this directory.
4Connect your terminal to the PC’s COM port. For instructions, see
your terminal user’s manual.
5Access the TRAKKER Antares 2400 Menu System. From the Main
Menu, select System Menu,thenUpgrade Firmware. The terminal re-
boots and displays LOADER WAITING.
6Run DOS program TE2SETUP. Its default settings are:
SBaud rate: 57600
SCOM port:1
SDiagnostic mode options:Disabled
To change these settings to match your system setup, refer to the online
help for the command line options. To access the help, type:
te2setup /h or te2setup /?
TE2SETUP downloads TE 2000 (CFGLIT.DAT, FWP*.BIN,
CFGLIT.DAT, FWP240Hx.BIN, ASCEBDIJ.TBL files) to your termi-
nal and, if necessary, defines the terminal’s new keypad configuration
table. Note that you can ignore the “Cannot read radio codes” message
that appears.
When done, TE2SETUP reboots your terminal into the TE 2000 ap-
plication. TE2SETUP retains your terminal’s current firmware and ter-
minal emulation configurations.
7If necessary, reconfigure the communication parameters for your net-
work. Access the TRAKKER Antares 2400 Menu System. From the
Main Menu, select Configuration Menu, then select Communications
Menu.

4 TE 2000  Installation Instructions
SFor the 2415, 2425, 2435A, 2455, 2475, 2485, or 2486 Terminals,
set the parameters as follows.
Parameter Setting
These parameters are located under Primary Network and are provided by the network administrator.
Network Activate 2.4 GHz RF or 802.11 DS (Default: Disabled)
Controller IP Addr (UDP Plus) (Default: 000.000.000.000)
Host IP Addr. (TCP/IP) (Default: 000.000.000.000)
Terminal IP Address (Default: 000.000.000.000)
These parameters are located under Advanced Network and are provided by the network administrator..
Subnet Mask (Default: 000.000.000.000)
Default Router (Default: 000.000.000.000)
These parameters are located under Radio.
Domain (2.4 GHz OpenAir) (Must match access point’s Domain or LAN ID) (Default: 0)
Security ID (2.4 GHz OpenAir) (Must match access point’s Security ID) (Default: null string for the 21XX Universal
Access Point and 011X Access Point; NORANDOWL for the 6710 Access Point)
Network Name (802.11 radio) (Must match 21XX UAP’s Network Name. If ANY is entered (all uppercase) the
terminal attempts to connect with any 802.11 21XX UAP) (Default: INTERMEC)
SFor the 2480 or 2481, set the parameters as follows.
Parameter Setting
These parameters are located under Primary Network and are provided by the network administrator.
Network Activate Ethernet (Default: Disabled)
Controller IP Addr (UDP Plus) (Default: 000.000.000.000)
Host IP Addr. (TCP/IP) (Default: 000.000.000.000)
Terminal IP Address (Default: 000.000.000.000)
These parameters are located under Advanced Network and are provided by the network administrator.
Subnet Mask (Default: 000.000.000.000)
Default Router (Default: 000.000.000.000)
Note: Ensure the terminal’s keypad type is set to its default keypad type
setting (see page 2). From the Configuration Menu choose Terminal
Menu. Check the setting for the Keypad parameter.
8If you changed the keypad type or reconfigured your network’s commu-
nication parameters, save the changes.
aFrom the Main Menu,pressd.
bAt the “Save new configuration (in RAM)?” prompt, choose Yes.
cFrom the Main Menu,pressd.
dAt the “Store configuration changes in flash memory?” prompt,
choose Yes.

5TE 2000  Installation Instructions
eAt the “Exiting TRAKKER Antares 2400 Menu System” screen,
choose CANCEL.
fFrom the Main Menu, select System Menu,thenFile Manager.
gAt the “Select drive:” option, select OK.
hSelect FWP240H0.BIN from the list of files. The terminal reboots.
9Configure the TE 2000 parameters.
aIf necessary, do the following to change the data stream. For Terminal
Emulation Version 6.0 or greater, the default data stream is “VT/ANSI.”
1Do the following to access the TE configuration menus:
SFor the 2415 37-key keyboard,press(5.
SFor the 2435A 57-key keyboard or the 39-key function numeric
keyboard,pressrl.
SFor the 2435A 48-key keyboard, press [Green] >[Orange] >
SFor all other terminals,press(¡.
2From the Main Menu, choose 1) Set-up Parms.
3At “Enter Password” prompt, type CR52401.
4Choose 3) Protocol Opts,2) Data Stream.
5Choose the appropriate terminal emulation.
bIf your host computer is configured to send extended commands to
the terminal, enable the Extended Commands option (default:
disabled). Select 3) Protocol Opts,3) Extended Cmds,1) Enabled.
cIf you are using 5250 or 3270 Terminal Emulation and the scanner
needs to be enabled all the time, then select 1) Set-Up Parms,
2) Barcode Parms,6) Scan All Flds. Scanning functions are disabled
while the terminal emulation configuration menus are open.
6Save your changes.
aFrom the Main Menu, choose 6) Exit Menus.
bAt the “Enter ‘Y’ to Save Parms” prompt, press Y.
cAt the “Enter Password” prompt, type CR52401.
The terminal reboots.

6 TE 2000  Installation Instructions
Global Services and Support
Web Support
Visit the Intermec web site at http://www.intermec.com to download our
current manuals in PDF format. To order printed versions of the Intermec
manuals, contact your local Intermec representative or distributor.
Visit the Intermec technical knowledge base (Knowledge Central) at
http://intermec.custhelp.com to review technical information or to request
technical support for your Intermec product.
Telephone Support
These services are available from Intermec Technologies Corporation.
Service Description
In the U.S.A. and Canada
call 1-800-755-5505
and choose this option
Factory Repair and
On-site Repair
Request a return authorization
number for authorized service
center repair, or request an
on-site repair technician.
1
Technical Support Get technical support on your
Intermec product.
2
Service Contract
Status
Inquire about an existing
contract, renew a contract, or ask
invoicing questions.
3
ScheduleSiteSurveys
or Installations
Schedule a site survey, or request
a product or system installation.
4
Ordering Products Talk to sales administration,
place an order, or check the
status of your order.
5
Outside the U.S.A. and Canada, contact your local Intermec
representative. To search for your local representative, from the Intermec
web site, click Contact.
Corporate Headquarters
6001 36th Avenue West
Everett, Washington 98203
tel [phone]
tax 425.355.9551
www.intermec.com
TE 2000 Installation Instructions - October 2003
*962-055-004*
P/N: 962-055-004 REV G
U.S.A.