International Concepts SW-54212 User manual

ITEM
NO
.
:
SW
-
54212
REVISED NOV 16, 2013
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
:
2 SEAT X
-
BACK PORCH SWING
: SW-54212

ITEM
NO
.
:
SW
-
54212
REVISED NOV 16, 2013
Printed in Vietnam
- 2 -
BEFORE ASSEMB
LY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Side Frame
(L-R) 2
B Back Frame 1
C Seat
Frame 1
D Apron 2
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM
NO
.
:
SW
-
54212
REVISED NOV 16, 2013
Printed in Vietnam
- 3 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO Description Qty Sketch NO Description Qty Sketch
1 Bolt
(M6x60mm) 8
2 Bolt
(M8x40mm) 2
3 Bolt
(M8x65mm) 4
4 Nut
(M6x13mm) 8
5
Short screw
(M4X15mm)
2 6 Allen Key
(4x80mm) 1
7 Flat washer
(8.5x19mm) 6 8 Lock washer (8.5x13mm) 6
9 Hexagon nut
(M8x7mm) 6
10
Wrench
(13mm)
1
11
Chains
(ɸ4x1220mm)
Chains (11.1)
(ɸ4x865mm)
Chains (11.2)
(ɸ4x915mm)
2
12 Somer’s Pointe 1
13 Nail
(Φ1mm x 12mm 2

ITEM
NO
.
:
SW
-
54212
REVISED NOV 16, 2013
Printed in Vietnam
- 4 -
STEP 1
Carefully attach the back frame (B) and aprons (D) to the side frames (A) with bolts (1) and nuts (4)
as shown below. Tighten with Allen key (6).

ITEM
NO
.
:
SW
-
54212
REVISED NOV 16, 2013
Printed in Vietnam
- 5 -
STEP 2
Place the seat frame (C) on the unit (from Step 1) as shown below.
STEP 3
Attach seat frame (C) to the unit with screws (5). Tighten with a screwdriver.
Attach side frames (A) to seat frame (C) with bolts (3) and nuts (9), lock washers (8) and flat washer
(7) as shown below. Tighten with the wrench (10).

ITEM
NO
.
:
SW
-
54212
REVISED NOV 16, 2013
Printed in Vietnam
- 6 -
STEP 4
Attach bolts (2) to side frames (A) with nuts (9), and lock washers (8) and flat washer (7) as shown
below. Tighten with the wrench (10).

ITEM
NO
.
:
SW
-
54212
REVISED NOV 16, 2013
Printed in Vietnam
- 7 -
STEP 5
Attach chains (11) to the side frames (A) as shown below.

ITEM
NO
.
:
SW
-
54212
REVISED NOV 16, 2013
Printed in Vietnam
- 8 -
STEP 6
Attach Somer’s Pointe plate (12) to the unit with nails (13) as shown below.