Nags Head Hammocks SINGLE BENT OAK PORCH SWING User manual

Instruction #: 5091NH, 0G.11
SINGLE BENT OAK
PORCH SWING
Congratulations! You now own a Bent Oak Porch Swing that was handcrafted
in North Carolina by Nags Head Hammocks. We hope you will have many
years of comfort and enjoyment. If you have any quesitons, please feel free
to contact us. Relax! It’s a Nags Head Hammock original.
P.O. Box 533
Nags Head, NC 27959
1-800-344-6433 •252-441-6115
www.nagshead.com
INSTALLATION :
Locate a suitable sturdy place to hang your swing. The support can be a
ceiling joist, a sturdy limb, or a beam installed for the swing. Ready made stands
or instructions to build one are available, please inquire. If ceiling joists are not
exposed, locate one using a stud nder.They are usually 16 to 24 inches apart.
Once you nd a suitable support, open the hanging kit and slip the closed end
of the ‘S’ hook onto the handle. Position the handle directly above the center of
your swing and drill two 3/16” starter holes. Secure with the two lag bolts. Use the
chain included in the hanging set to adjust the height of your swing. We nd that
the swing is easiest to use when it hangs about 15” o the ground; low enough to
keep your feet on the oor.
MAINTENANCE :
The rope body of your Bent Oak Swing is hand woven. If the weave of the rope
body is pulled out of shape, you can brush or adjust it into shape with your hands.
To keep your bent oak swing in good condition, it is very important to consistantly
check the varnish for weather damage. The wood frame should be periodically
renished using a high quality polyurethane varnish. For complete instructions
on renishing your swing, please visit www.nagshead.com/care.asp, or give us a
call. To wash the rope seat, you can either leave the ropes attached to the chair
or remove them. Before removing the ropes from the wooden bars, slide
guide ropes through the topmost and bottommost row of loops, and
tie them o. You will need OxiClean or laundry detergent and a soft scrub brush.
To begin cleaning, wet the rope and apply the detergent. Additionally, you may
use a very mild bleach solution, but be sure to rinse the ropes thoroughly
afterwards. Take a handful of rope in each hand and rub the pieces together;
using the soft-bristled scrub brush to work on any stains. Once you’ve cleaned all
of the rope, rinse it thoroughly. If you have removed the rope from the chair,
arrange it on a at surface to air-dry so that the rope does not stretch.
If you have any questions about maintaining your chair, please give us a call at
1-800-344-6433 or 252-441-6115
WARRANTY AND RETURNS :
Nags Head Hammocks products are guaranteed to be free of defects in both work-
manship and material. Prolonged exposure to weather conditions including snow,
rain, and humidity are not covered under the warranty, nor is damage caused by
normal wear, mildew, or improper care, including storage, maintenance, and as-
sembly. If you are not satised with an item, return it unused in its original pack-
aging for a complete refund or exchange. You can return it to any of our stores
or to our warehouse, Nags Head Hammocks, 305 Industrial Blvd., Greenville, NC
27834. Please include a copy of your receipt and your contact information.

1 Loose Bar
1 Roll-Up :
2 Bent Oak Arm Units
1 Hardware Pack:
1 Hanging Kit:
PARTS LIST :
Instruction Sheet
3” Carriage Bolts
Washers
Lock Washers
Hex Nuts
Chain Assemblies
(1)
(2)
(2)
(2)
(2)
(2)
Tips for Assembly :
Tip 1: Do not tighten bolts completely until fully
assembled
Tip 2: For a more uniform look, face all bolts in the
same direction
Tip 3: Before assembly, lay the chain sets on a at
surface. Make sure chains are completely untwisted.
ASSEMBLY :
Note: The “top” bar of the roll-up features a thin
wooden strip with brass tacks. The “bottom” bar
has a thicker wooden strip attached with screws.
You Will Need : One 7/16” wrench and a mallet or hammer
1 Spreader Bar with Logo
Step 1 : Set the arm units on the oor approximately 3 feet apart. If sitting in the
swing, the branded arm unit should be on your right hand side.
Step 2 : Locate the loose bar and insert a bolt into each hole. Tap the bolts with a
hammer until the head of the bolt is ush with the wood.
Step 2 : Take the loose bar and attach it to the inside of one arm unit under the
curved arm. Secure with a washer, lockwasher and nut. Repeat on the other side.
Step 4 : Attach the ‘top’ bar of the roll-up to the back of the swing using the eye-
bolt found on the ‘short’ chain piece (See Diagram). Secure with washer and nut.
Repeat on other side.
Step 5 : Attach the ‘bottom’ bar of the roll-up to the front of the swing using the
eyebolt found on the ‘long’ chain piece (See Diagram). Secure with washer and
nut. Repeat on the other side.
Step 6 : Install the spreader bar by inserting the unattached end of one of the
chain sets up through one of the holes in the spreader bar. Make sure the logo
faces front. Repeat on the other side, then slide the bar down the chain until it
settles.
Step 7 : Tighten all hardware
DIAGRAM :