Intex Krystal Clear CS8220G User manual

132
GS
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
OOWWNNEERR’’SS AANNUUAALL
I PORTANT
SAFETY RULES
Read, understand, and follow all
instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: pools, pool accessories,
inflatable pools and in-home toys, airbeds and boats available at fine
retailers or visit our website.
132-GSA-R1-1211
©2011 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O
Box 28829, ong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • istributed in the European
Union by/ istribué dans l’Union Européenne par/ istribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/Intex Trading B.V., P.O. Box nr. 1075 – 4700 BB Roosendaal – The Netherlands
For illustrative purposes only.
Krystal Clear™
Saltwater System
odel CS8220G, 12 V~, 50 Hz
125 W, IPX5

132
GS
SAVE T ESE INSTRUCTIONS Page 2
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
TTAABBLLEE OOFF CCOONNTTEENNTTSS
Warnings............................................................................... 3
Parts List & References....................................................... 4-6
Product Information & Specifications................................ 7
Setup Instructions................................................................ 8-12
Salt & Pool Water Volumes.................................................. 13
Intex Pools Salt Table........................................................... 14
Intex Pools Operating Time Table....................................... 15
Intex Pools Cyanuric Acid Table......................................... 16
Non-Intex Pools Salt Table................................................... 17
Non-Intex Pools Operating Time Table............................... 17
Non-Intex Pools Cyanuric Acid Table................................. 17
Operating Instructions......................................................... 18-19
LED Code Chart................................................................... 20
Stationary Mounting Option................................................ 21
Maintenance.......................................................................... 22-24
Long Term Storage............................................................... 24
Pool Maintenance and Chemical Definitions..................... 25
Troubleshooting Guide........................................................ 26-27
General Aquatic Safety........................................................ 28
Limited Warranty.................................................................. 29
Intex Service Center Locations........................................... 30

132
GS
SAVE T ESE INSTRUCTIONS Page 3
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSAAFFEETTYY RRUULLEESS
WARNING
•To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
•Children must stay away from this product and electrical cord(s).
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge. They
must at all times be supervised by a knowledgeable and experienced adult
responsible for their safety.
•Assembly and disassembly by adults only.
•Risk of electric shock. Connect transformer only to a grounding type receptacle
protected by a ground-fault circuit interrupter (GFCI) or residual current device
(RC ). Contact a qualified electrician if you cannot verify that the receptacle is
protected by a GFCI/RC . Use a qualified electrician to install the GFCI/RC ,
which has a maximum rate of 30mA. o not use a portable residual current device
(PRC ).
•Always unplug the transformer from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
• The plug must be accessible after produc t is installed.
• o not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
•The supply cord cannot be replaced. If the cord is damaged the appliance or
transformer should be scrapped.
•To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
•o not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
•Keep the transformer more than 3.5m away from the pool.
•Keep the plug of the transformer more than 3.5m away from the pool.
• Position this product away from the pool, so as to prevent children from climbing on
it and accessing the pool.
•o not operate this product when the pool is occupied.
•This product is for use with storable pools only. o not use with permanently
installed pools. A storable pool is constructed so that it may be readily
disassembled for storage and reassembled to its original configuration.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW T ESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC S OCK, ENTANGLEMENT OR
OT ER SERIOUS INJURY OR DEAT .
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
I PORTANT SAFETY RULES
Read, Understand and Follo All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
For portable Above-Ground-Pools only

132
GS
SAVE T ESE INSTRUCTIONS Page 4
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
PPAARRTTSS LLIISSTT
PARTS LIST
NOTE: rawings for illustration purpose only. Actual product may vary. Not to scale.
123
456
789
10 11 12
* Optional
* Optional
13

132
GS
SAVE T ESE INSTRUCTIONS Page 5
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
PPAARRTTSS RREEFFEERREENNCCEE
PARTS REFERENCE
Before assembling your product, please take a fe minutes to check the contents
and become familiar ith all the parts.
1
2
3
5
42689
10
NOTE: rawings for illustration purpose only. Actual product may vary. Not to scale.
2
7
13

132
GS
SAVE T ESE INSTRUCTIONS Page 6
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
PPAARRTTSS RREEFFEERREENNCCEE
When ordering parts, be sure to quote the model number and part numbers.
REF. NO.
DESCRIPTION QTY.
SPARE
PART
NO.
COMMON
PARTS
PARTS FOR
CONNECTION
TO FILTER
PUMPS WIT
1-1/4" (32MM)
OSE SIZE
1 A APTOR A WITH THREA E COLLAR (OPTIONAL) 1 10849
2 O-RING A 3 10712
3 SCREW 4 10713
4ELECTROLYTIC CELL (WITH TITANIUM
PLATES) (O-RING A INCLU E ) 1 11233
5 COPPER ELECTRO E 1 11234
6FLOW SENSOR CON UIT (O-RING B &
O-RING C INCLU E ) 1 11250
7 FLOW SENSOR 1 11460
8 CONNECTOR HOSE WITH THREA E FITTINGS 1 10720
9 THREA E A APTOR B (OPTIONAL) 1 10722
10 CELL COVER 2 11131
11 CHLORINE TEST STRIPS 1 19635
12 COPPER TEST STRIPS 1 11254
13 COPPER ELECTRO E NUT 1 11488
PARTS REFERENCE (continued)
Before assembling your product, please take a fe minutes to check the contents
and become familiar ith all the parts.

132
GS
SAVE T ESE INSTRUCTIONS Page 7
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
PPRROODDUUCCTT IINNFFOORRAATTIIOONN//SSPPEECCSS
This product is specially designed for above ground pools. It will destroy the
bacteria, oxidize bather organics and control algae, which provide a safe, clean and
comfortable swimming pool.
Common salt (sodium chloride) is made up of two elements, sodium and chloride.
uring the installation of your Saltwater System, a measured quantity of salt is
dissolved in the pool water to make it slightly salty. The pool water flows through
the Saltwater System ’s electrolytic cell to produce chlorine. The chlorine dissolves
in the water and instantly starts destroying bacteria and algae. It also oxidizes all
other organic materials.
Low voltage direct current is applied to the copper electrode, and copper ions are
generated and dissolved instantly in the water. Copper is an effective algaecide,
which will prevent algae from growing in the pool.
HOW THE CHLORINE IS GENERATED
Wattage: 125W
Ideal Salt Level: 3000 ppm (parts per million)
Maximum Chlorine Output/hour: 12 grams/hour
Copper Ionizer Output Current: 175 mA
Minimum Flow Rate: 700 ~ 4000 gallons/hour (2650 - 15140 liters/hour)
Limited Warranty: see “Limited Warranty”
HOW COPPER IONS ARE GENERATED
PRODUCT SPECIFICATIONS
Electronic
Control Station
Power Supply
Flow SensorElectrolytic Cell
Copper electrodes

132
GS
SAVE T ESE INSTRUCTIONS Page 8
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
SETUP INSTRUCTION
1. Assemble the above-ground-pool (AGP) and its filter pump according to their
installation instructions.
2. Take the Saltwater System and its accessories out of the packaging.
3. Place the Saltwater System in line after the filter pump.
4. Connect the connector hose (8) to the Saltwater System inlet.
Connecting the system to pump and pool with 1-1/4” (32mm)
connections/hoses:
The saltwater system features 1-1/2” (38mm) connections. It is accordingly
supplied with adaptors A (1) and B (9) for connecting to the small 1-1/4”
(32mm) diameter connections/hoses. Install as follows:
Drawing #1
IMPORTANT
•The Saltwater System requires a separate filter pump [700~4000 gph
(2650~15140 lph)] to drive the water and function properly.
• The Saltwater System must be installed as the last piece of pool
equipment in the water return line to the pool as displayed in Drawing
#1. This location extends the life of the titanium plates.
BOOST
1
9
8
WATER TO
POOL
WATER FROM
POOL
FILTER
PUMP
SWIMMING POOL
SALTWATER
SYSTEM
3.5M
I 1-1/2” (38mm)
HOSE

132
GS
SAVE T ESE INSTRUCTIONS Page 9
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
SETUP INSTRUCTION (continued)
1. Go directly to step 2 if your pool is empty. If your above-ground-pool is filled
with water, unscrew the strainer grids from the strainer connectors and insert
the black hat-like plugs into the connectors, before installing the saltwater pool
system.
2. Connect the adaptor A (1) to the electrolytic cell (4) outlet as shown in rawing
#1. Tighten securely.
3. isconnect the water return hose from the filter pump connection and connect
it to the adaptor A (1) on the Saltwater System with a hose clamp. (see
rawing #1)
4. Connect adaptor B (9) to the connector hose (8). Tighten securely. (see
rawing #1)
5. Connect adaptor B (9) to filter pump outlet (lower connection). Tighten
securely.
6. Remove the black hat-like plugs that prevent water from flowing out of the pool.
Now, return the strainer grids to the strainer connectors.
8
9
14
8
9
Filter
Pump

132
GS
SAVE T ESE INSTRUCTIONS Page 10
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
SETUP INSTRUCTION (continued)
Connecting the system to pump and pool with 1-1/2” (38mm)
connections/hoses:
Pump and pool with 1-1/2” (38mm) connections do not require the adaptors
A (1) or B (9). Install as follows:
Drawing #2
1. Go directly to step 2 if your pool is empty. If your above-ground-pool is filled
with water, close the plunger valves before installing the Saltwater System.
2. isconnect the water return hose from the filter pump connection and connect
it to the Saltwater System outlet.
3. Connect the connector hose (8) to the filter pump outlet connection.
4. Open the plunger valves to allow the water to flow.
BOOST
FILTER
PUMP
SWIMMING POOL
WATER TO
POOL
PLUNGER
VALVE
WATER FROM
POOL
I 1-1/2” (38mm)
HOSE
SALTWATER
SYSTEM
3.5M

132
GS
SAVE T ESE INSTRUCTIONS Page 11
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
SETUP INSTRUCTION (continued)
English
Connecting the system to other types of pump (with different type of
thread or no thread):
The Saltwater System can also be adapted to other filter pumps with different
thread or those without a thread on the connection.
Connection to 1-1/4” (32mm) hose:
1. Connect one end of adaptor B (9) to the connector hose (8). Tighten securely.
2. Now, connect the other end of adaptor B (9) to the filter pump outlet. Tighten
securely.
Connection to 1-1/2” (38mm) hose with clamp:
1. Connect the connector hose (8) to the filter pump outlet connection with a large
hose clamp. Tighten securely.
FILTER PUMP
FILTER PUMP
89
I 1-1/4” (32mm)
CONNECTION
SALTWATER SYSTEM
8LARGE HOSE
CLAMP
I 1-1/2” (38mm)
CONNECTION
SALTWATER SYSTEM

132
GS
SAVE T ESE INSTRUCTIONS Page 12
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
SETUP INSTRUCTION (continued)
Connecting the system to other types of pool
After you have connected the Saltwater System to the pump, connect it to
the pool. This is depicted in rawings #1 and #2.
Following are the common connection types:
Connection to 1-1/4” (32mm) connectors:
1. Connect the adaptor A (1) to the electrolytic cell (4) outlet. Tighten securely.
2. The adapter A (1) is now fitted to the Saltwater System. The following step is to
connect the water return hose to the adaptor A (1) with a hose clamp.
Connection to 1-1/2” (38mm) connectors without thread:
1. Connect the adaptor A (1) to the electrolytic cell (4) outlet. Tighten securely.
2. With the adaptor A (1) fixed to the Saltwater System, connect the water return
hose to the adaptor, using a large hose clamp.
1
HOSE CLAMP
I 1-1/4” (32mm)
HOSE
SALTWATER SYSTEM
1
LARGE HOSE CLAMP
I 1-1/2” (38mm)
HOSE
SALTWATER SYSTEM

132
GS
SAVE T ESE INSTRUCTIONS Page 13
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SSAALLTT && PPOOOOLL WWAATTEERR VVOOLLUUEESS
SALT & POOL WATER VOLU ES
• Which kind of salt to use:
Use only Sodium Chloride Salts
Use only sodium chloride (NaCl) salt that is at least 99.8% pure. It is also
acceptable to use water conditioning salt pellets (the compressed forms of
evaporated salt). However, it will take a longer time for them to dissolve.
Do not use iodized or yellow (yellow prussiate of soda) colored salt.
Salt is added to the pool water and the electrolytic cell uses the salt to create
chlorine. The purer the salt the better the performance of the electrolytic cell.
• Optimum Salt Levels
The ideal salt level in the pool water is between 2500-3500 ppm (parts per million).
The optimal level is 3000 ppm.
A too low salt level will reduce the efficiency of the Saltwater System and result in
low chlorine production. A high salt level may generate a salty taste to the pool
water (this may occur at a salt level above 3500-4000ppm). Too high a salt level
may damage the power supply and cause corrosion to the pool metal fixtures and
accessories. The Salt Table page of this manual, shows the correct dosage of salt
needed. The salt in the pool is constantly recycled. The loss of salt is due only to
pool water being physically removed from the pool. Salt is not lost due to evapora-
tion.
• Adding Salt
1. Switch the filter pump on to start the water circulation.
2. Keep the Saltwater System turned off.
3. etermine the amount of salt to be added (see “Salt Table”).
4. Evenly spread the proper amount of salt around the inside perimeter of the
pool.
5. Avoid clogging the filter. o not add salt through the skimmer.
6. Brush the pool bottom to speed up the dissolving process. o not allow salt to
pile up on the bottom of the pool. Run the filter pump 24 consecutive hours to
thoroughly dissolve the salt.
7. After 24 hours and if all the salt is dissolved, turn on the Saltwater System,
press button until you hear a “beep”, code “00” flashing and set the saltwater
pool system to desired operating time (see “Operating Time Table”).
• Removing Salt
If too much salt has been added, the unit will beep and display “Code 92” (see
“Alarm Codes”). You will need to lower the salt concentration. The only way to do so,
is to partially drain the pool and refill it with fresh water. rain and refill
approximately 20% of the pool’s water until the “Code 92” disappears.
• Pool Volume Calculation
Rectangular Length x Width x Average epth x 7.5 Length x Width x Average epth
Circular Length x Width x Average epth x 5.9 Length x Width x Average epth x 0.79
Oval Length x Width x Average epth x 6.0 Length x Width x Average epth x 0.80
Types of Pool Gallons
(pool size in feet)
Cubic Meters
(pool size in meters)

132
GS
SAVE T ESE INSTRUCTIONS Page 14
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
INTEX POOLS SALT TABLE
This table shows the amount of salt needed to achieve and maintain the optimal 3000 ppm
salt level.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Salt Needed for
Startup
3.0g/L (3000ppm)
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME®
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (
569 cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587 9792 65 30 20 10
2822 10681 65 30 20 10
3284 12430 80 35 20 10
3736 14141 95 45 20 10
3754 14209 95 45 20 10
4273 16173 110 50 30 15
4786 18115 120 55 30 15
5455 20647 135 60 35 15
5894 22309 150 65 40 20
3282 12422 80 35 20 10
3861 14614 100 45 20 10
4440 16805 110 50 30 15
5061 19156 125 55 30 15
6423 24311 160 75 40 20
6981 26423 175 80 45 20
8638 32695 220 100 60 25
11483 43462 290 130 75 35
12481 47241 310 140 85 40
5061 19156 125 55 35 15
6981 26423 175 80 45 20
5061 19156 125 55 35 15
6981 26423 175 80 45 20
2885 10920 65 30 20 10
4393 16628 110 50 30 15
5407 20465 135 60 35 15
6420 24300 160 75 40 20
4545 17203 115 50 30 15
8403 31805 210 100 55 25
14364 54368 360 165 95 45

132
GS
SAVE T ESE INSTRUCTIONS Page 15
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
INTEX POOLS OPERATING TI E TABLE (WITH CYANURIC ACID)
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Operating Time (hours)
at different ambient/air
temperatures
Intex Filter
pump
Operating
Time
(hours)
(Gals) (Liters)
10 - 19°C
(50 - 66°F)
20 - 28°C
(68 - 82°F)
29 - 36°C
(84 - 97°F)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME®
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (
569 cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587
2822
3284
3736
3754
4273
4786
5455
5894
3282
3 861
4440
5061
6423
6981
8638
11483
12481
5061
6981
5061
6981
2885
4393
5407
6420
4545
8403
14364
9792
10681
12430
14141
14209
16173
18115
20647
22309
12422
14614
16805
19156
24311
26423
32695
43462
47241
19156
26423
19156
26423
10920
16628
20465
24300
17203
31805
54368
1
1
1
1
1
2
2
2
2
1
1
2
2
2
2
3
4
5
2
2
2
2
1
2
2
2
2
3
6
1
1
1
2
2
2
2
2
2
1
2
2
2
2
2
3
4
5
2
2
2
2
1
2
2
2
2
3
6
1
1
2
2
2
2
2
3
3
2
2
2
2
3
3
4
5
6
2
3
2
3
1
2
3
3
2
4
7
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
8
4
4
4
4
2
4
4
4
4
6
8
IMPORTANT
The filter pump running time should be 1 hour longer than the required
operating time of the Saltwater System.

132
GS
SAVE T ESE INSTRUCTIONS Page 16
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
INTEX POOLS CYANURIC ACID TABLE
Cyanuric acid is a chemical that reduces the loss of chlorine in water due to ultraviolet
rays. To maintain maximum performance, we recommend that the cyanuric acid level be
maintained at approximately
1% of the salt, i.e. 100 Lbs (45 Kgs) salt x1% = 1 Lbs (0.45 Kgs)
cyanuric acid.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Cyanuric Acid Needed for
Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME®
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (569cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587 9792 0.6 0.3
2822 10681 0.7 0.3
3284 12430 0.8 0.4
3736 14141 0.9 0.4
3754 14209 0.9 0.4
4273 16173 1.1 0.5
4786 18115 1.2 0.5
5455 20647 1.4 0.6
5894 22309 1.5 0.7
3282 12422 0.8 0.4
3861 14614 1.0 0.4
4440 16805 1.1 0.5
5061 19156 1.3 0.6
6423 24311 1.6 0.7
6981 26423 1.7 0.8
8638 32695 2.2 1.0
11483 43462 2.9 1.3
12481 47241 3.1 1.4
5061 19156 1.3 0.6
6981 26423 1.7 0.8
5061 19156 1.3 0.6
6981 26423 1.7 0.8
2885 10920 0.7 0.3
4393 16628 1.1 0.5
5407 20465 1.4 0.6
6420 24300 1.6 0.7
4545 17203 1.1 0.5
8403 31805 2.1 1.0
14364 54368 3.6 1.6

132
GS
SAVE T ESE INSTRUCTIONS Page 17
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
SALT TABLE FOR CO ON NON-INTEX POOLS
OPERATING TI E TABLE FOR CO ON NON-INTEX POOLS
SALT CALCULATION FOR ULA FOR ALL POOLS
Water Capacity Salt Needed for Startup
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)
2000 7500 50 20 10 5
4000 15000 100 45 25 10
6000 22500 150 65 40 20
8000 30000 200 90 55 25
10000 37500 250 110 70 30
12000 45500 300 135 80 35
14000 53000 350 160 95 45
Salt Needed for Startup
(Lbs)
Salt Needed for Startup
(Kgs)
Salt Needed when
Low Salt Detected (Lbs)
Salt Needed when
Low Salt Detected (Kgs)
Water Capacity (Gals) x 0.025
Water Capacity (Liters) x 0.003 Water Capacity (Gals) x 0.0067 Water Capacity (Liters) x 0.0008
Water Capacity Operating Time (hours)
at different ambient/air temperatures
(Gals) (Liters) 10 - 19°C
(50 - 66°F)
20 - 28°C
(68 - 82°F)
29 - 36°C
(84 - 97°F)
2000
4000
6000
8000
10000
12000
14000
7500
15000
22500
30000
37500
45500
53000
1
2
2
3
4
5
6
1
2
3
4
5
6
7
1
2
2
3
4
5
6
CYANURIC ACID TABLE FOR CO ON NON-INTEX POOLS
Water Capacity Cyanuric Acid Needed for Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
2000
4000
6000
8000
10000
12000
14000
7500
15000
22500
30000
37500
45500
53000
0.23
0.45
0.68
0.90
1.13
1.37
1.59
0.5
1.0
1.5
2.0
2.5
3.0
3.5

132
GS
SAVE T ESE INSTRUCTIONS Page 18
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
OPERATION INSTRUCTIONS
OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS
1. Turn on the filter pump.
2.Start up the unit:
Plug the power cord into the
electrical outlet and test the
GFCI/RC (circuit breaker). Switch
on the unit. Flashing code “00” appears
on the electronic control station’s LE ,
indicating that the unit is ready to be
programmed.
3. Set operating hours for Saltwater system:
With code “00” flashing, press button to
set the desired operating hours. See the
“Operating Time Table” for the required
operating hours related to each pool size.
Pressing will increase the time from 01
to 12 hours maximum. If you have selected
too many hours keep pressing to repeat
the cycle. The built-in timer will now activate
your Saltwater System, at the same time each
day, for the number of hours you have set.
NOTE: The Saltwater System will not operate if the filter pump is not operating.
Make sure to program your filter pump (or start it manually) for operation
beginning 5 minutes before the saltwater system and finishing 15 minutes after
the saltwater system.
4.Lock keypad controls:
With the desired hour value showing, press button until
you hear a “beep”. A green “WORKING” indicator on the
control panel will light up within a few seconds to indicate that
the saltwater system has started chlorine production. Locking
the control buttons into this setting prevents unauthorized
changing of the operating cycle.
NOTE: If you forget to lock the keypad controls, the system
will automatically lock it and start working 1 minute later.
5. Readjust operating time if necessary:
The operating hours can be re-adjusted if necessary.
Press button until you hear a “beep” to unlock the
keypad and the current programmed time will flash.
Repeat steps 3 to 4.
6.Test the copper concentration in the
pool water.
The Saltwater System recommends a copper level of 0.1 to 0.2 ppm. This is
easily tested by the copper ion test strips provided. If the test result is 0.1~0.2
ppm, go directly to step 8.
(1 to 12 hours max per cycle)
OK
0
Copper (ppm)
0.1 0.2 0.5 0.9 1.3

132
GS
SAVE T ESE INSTRUCTIONS Page 19
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
OPERATION INSTRUCTIONS (continued)
OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS
7.Boost cycle
•If the test result is below 0.1ppm, press and hold “BOOST”
button for 5 seconds until the indicator lights up and the
LE display shows “80”. This indicates that the saltwater
system has started copper ion and more chlorine sanitizer
production. You can press and hold the “BOOST” button for
another 5 seconds until the indicator is off, which will cancel
the Boost cycle.
Note: Once the system has started copper ion and more chlorine sanitizer
production, the boost button can’t be re-set until the power switch is off.
•The boost operating hours is 4 times the amount of time programmed into the
system, i.e. if your saltwater system operating time is 2 hours, the boost procedure
will run 4 x 2 = 8 hours. After boost procedure has been completed, the system
will automatically switch to the normal working mode.
•Once the boost is operating, check whether the filter pump operating hours
have been set properly. For example, the boost operating time is 8 hours, the
filter pump should be set to run for 8 hours at least. Increase the filter pump
operating time if necessary.
Note: If an Intex filter pump is attached to the system, set the pump switch to
on “I” position.
•After a heavy rain or if the pool is dirty, press the “BOOST” button to shock the
pool again.
8.Test pool water regularly:
Once the copper level appears to be balanced, test the pool water every week
to maintain the proper sanitizer level.
It’s very important that the free chlorine is between 0.4-1.5 ppm and copper
ion concentration is between 0.1~0.2 ppm. When the copper level is below 0.1
ppm, repeat step 7.
NOTE: A High copper ion concentration may cause blonde hair to exhibit a
green hair. To prevent this, wear a swimming cap during swimming, and wash
hair with special shampoo after using the pool.
See “Troubleshooting Guide”.
9. Stand-by/power saving mode:
•When the cycle ends, the green “SLEEP” indicator on the
control panel lights up and the LE display flashes “93”.
The system is now in Stand-By mode. After a while, it
shuts down and sets itself in a Power Saving mode. The
system will automatically turn itself back on in 24 hours,
starting its daily cycle of chlorine production.
•The “SLEEP” indicator stays on, while the system is in the
Power Saving mode. The LE display however, goes blank
after 1 hour. Press any button ( or ) to view the last LE
code.

132
GS
SAVE T ESE INSTRUCTIONS Page 20
(132GS) MO EL CS8220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 11/17/2011
English
LLEEDD CCOODDEE CCHHAARRTT
LED CODE CHART
LED Reading Definitions
80 Boost Mode
00 Stand-By Mode (Start-up)
01 Minimum Operating Hour (1 hour remaining)
02 Operating Hours (2 hours remaining)
03 Operating Hours (3 hours remaining)
04 Operating Hours (4 hours remaining)
05 Operating Hours (5 hours remaining)
06 Operating Hours (6 hours remaining)
07 Operating Hours (7 hours remaining)
08 Operating Hours (8 hours remaining)
09 Operating Hours (9 hours remaining)
10 Operating Hours (10 hours remaining)
11 Operating Hours (11 hours remaining)
12 Maximum Operating Hours (12 hours remaining)
90 Alarm Code (Low Water Flow / No Flow)
91 Alarm Code (Low Salt Level)
92 Alarm Code (High Salt Level)
93 Stand-By Mode (Operating Process finished)
“BLANK” No Power or “Power Saving Mode” waiting to start next
Saltwater System cycle.
IMPORTANT
When Code “90” alarm is shown, ensure the timer of the filter pump is set
one (1) hour longer than the Saltwater System.
If the filter pump does not have a built-in timer, the filter pump needs to
be turned on/off manually every day.