Intex SF70220RC-1 User manual

Zusammengeführte PDF Datei. Die Originale sind im folgenden Verzeichnis verlinkt. / Merged PDF File. Original files are linked in the following list. / Sloučený soubor PDF.
Originály jsou propojeny v následujícím adresáři. / Egyesített PDF fájl. Az eredetiek a következő könyvtárban találhatók. / Zlúčený súbor PDF. Originály sú prepojené v
nasledujúcom adresári. / Združena datoteka PDF. Izvirniki so povezani v naslednjem imeniku. / Spojena PDF datoteka. Izvornici su povezani u sljedećem imeniku.
128648GS - Krystal Clear sand filter unit SF70220RC-1
195GS 2
Air Valve For Water Revitalization Set 25
Hydro Aeration Technology 27
Service Center 29

195
GS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Model SF80220RC-1
220-240 V~, 50 HZ, 250 W, Hmax 5 m Hmin 0.19 m IPX4
Model SF70220RC-1
220-240 V~, 50 HZ, 450 W, Hmax 7.5 m Hmin 0.19 m IPX4
Model SF60220RC-1
220-240 V~, 50 HZ, 550 W, Hmax 7.5 m Hmin 0.19 m IPX4
MAX. WATER TEMPERATURE 35°C
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves
the right to change specifications and appearance, which may
result in updates to the instruction manual without notice.
©2017 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O
Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European
Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com
For illustrative purposes only.
OWNER’S MANUAL
195-*GS-R0-1809
IMPORTANT
SAFETY RULES
Please read, understand, and follow all
instructions carefully before installing
and using this product. Keep for future
reference.

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 2
Warnings.......................................................................... 3
Parts References............................................................. 4-5
Setup Instructions ......................................................... 6-13
Product Specifications................................................... 8
Operating Instructions ................................................... 14-16
Intex Pools Operating Time Table..................................17
Non-Intex Pools Operating Time Table..........................18
Maintenance.................................................................... 19
Long Term Storage..........................................................20
Troubleshooting Guide................................................... 21
Common Pool Problems................................................. 22
General Aquatic Safety................................................... 22
Limited Warranty............................................................. 23
TABLE OF CONTENTS

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 3
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
• Always supervise children and those with disabilities.
• Children must stay away from this product and electrical cord(s).
• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without
supervision.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved.
• Assembly and disassembly by adults only. Cleaning and user maintenance must be performed by an adult above
18 years old who is familiar with the risk of electric shock.
• Risk of electric shock. Connect this product only to a grounding type receptacle protected by a ground-fault circuit
interrupter (GFCI) or residual current device (RCD). Contact a qualified electrician if you cannot verify that the
receptacle is protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, which has a maximum
rate of 30mA.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment
to the product.
• Always unplug the appliance on raining days or if leave it for long time (such as going out for holidays).
• The plug must be accessible after product is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and
other equipment.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
• To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to connect
unit to electric supply; provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
• Keep this product more than 3.5m away from the pool.
• Keep the plug of this product more than 4m away from the pool and at a height of 1.2m at least.
• Position this product away from the pool, so as to prevent children from climbing on it and accessing the pool.
• Do not operate this product when pool is occupied.
• This product is for use with storable pools only. Do not use with permanently installed pools. A storable pool is
constructed so that it may be readily disassembled for storage and reassembled to its original configuration.
• To reduce the risk of entrapment hazard, never enter the pool if suction strainer component is loose, broken,
cracked, damaged or missing. Replace loose, broken, damaged, cracked or missing suction strainer components
immediately.
• Never play or swim near suction fittings. Your body or hair may be trapped causing permanent injury or drowning.
• To prevent equipment damage and risk of injury, always turn pump off before changing the filter control valve
position.
• Never operate this product above the maximum working pressure stated on the filter tank.
• Hazardous Pressure. Improper tank valve cover assembly could cause the valve cover to blow off and cause
serious injury, property damage or death.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE, ELECTRIC SHOCK,
ENTANGLEMENT OR OTHER SERIOUS INJURY OR DEATH.
These product warnings, instructions and safety rules provided with the product represent some common risks of
water recreation devices and do not cover all instances of risk and danger. Please use common sense and good
judgement when enjoying any water activity.

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 4
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
" * ": Optional.
1
5
9
11
2
13
35
20
32
33 34 19
3
6
7
4
12
15
16
17
18
8
10
14
36
37
38
19
20
39
23 28
21
22
29 31
*
23 24
21
22
25 26
*40
21
23 24 25 27
22
*41
42
23 28 30
21
*
22
44
41
43

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 5
REF. NO. DESCRIPTION QTY. SPARE PART NO.
SF80220RC-1 SF70220RC-1 SF60220RC-1
1 PRESSURE GAUGE 1 11411 11224 11224
2 6-WAY VALVE 1 11378 11496 11496
3 DRAIN OUTLET COVER 1 11131 11131 11131
4 CLAMP 1 11380 11380 11380
5 TANK O-RING 1 11379 11379 11379
6 SAND SHIELD 1 11382 11382 11382
7 CENTER PIPE HUB 1 11815 11813 11814
8 LATERAL 10 11484 --
12 - 11384 11384
9 DRAIN VALVE CAP 1 11456 11456 11456
10 DRAIN VALVE O-RING 1 11385 11385 11385
11 L-SHAPE O-RING 4 11228 11228 11228
12 HOSE WITH NUTS 2 11769 11769 11769
13 SAND FILTER INTERCONNECTING HOSE 1 11820 11388 11535
14 LEAF TRAP NUT 1 11822 11479 11479
15 LEAF TRAP O-RING 1 11824 11232 11232
16 BASKET 1 11821 11260 11260
17 FILTER HOUSING NUT 1 11261 11261 11261
18 L-SHAPE O-RING 1 11412 11412 11412
19
AIR RELEASE VALVE/SEDIMENT RELEASE VALVE
2 10460 10460 10460
20 VALVE O-RING 2 10264 10264 10264
21*
PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED) 2 10747 10747 10747
22* HOSE O-RING 2 10262 10262 10262
23* STEP WASHER 2 10745 10745 10745
24* STRAINER NUT 2 10256 10256 10256
25* FLAT STRAINER RUBBER WASHER 2 10255 10255 10255
26* THREADED STRAINER CONNECTOR 1 11235 11235 11235
27 ADJUSTABLE POOL INLET JET NOZZLE 1 12369 12369 12369
28* ADAPTOR B 2 10722 10722 10722
29*STRAINER CONNECTOR 1 11070 11070 11070
30*POOL INLET JET NOZZLE 1 12364 12364 12364
31*STRAINER GRID 112197 12197 12197
32 SCREW 2 11381 11381 11381
33 PUMP MOTOR & CONTROL 1 12492GS 12488GS 12490GS
34 PRE-FILTER ASSEMBLY 1 11826 11371 11371
35 LEAF TRAP COVER 1 11823 11480 11480
36 SAND FILTER PUMP MOTOR INLET O-RING 2 11457 11457 11457
37 SAND FILTER PUMP TANK 1 11804 11802 11803
38 SAND FILTER PUMP TANK BASE 1 11816 11800 11801
39 PRE-FILTER HOUSING 1 12100 12099 12099
40* STRAINER GRID 1 12198 12198 12198
41* AIR JET VALVE 1 12363 12363 12363
42* INLET THREADED AIR CONNECTOR 1 12371 12372 12372
43* POOL INLET AIR ADAPTOR 1 12368 12368 12368
44* INLET STRAINER CONNECTOR 1 12365 12365 12365
45* AIR JET VALVE CAP (NOT SHOWN) 1 12373 12373 12373
" * ": Optional.
When ordering parts, be sure to quote the model number and part numbers.

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 6
The strainer grid prevents large objects from jamming and/or damaging the filter pump. If
your pool has an inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The part numbers here onward refer to the parts depicted
in the Parts List section of this manual. To install, do the following:
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector
(26) (see drawing 1).
Be careful not to lose the step rubber
washer
(23). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut
(24) from the threaded
connector
(26). Leave the flat washer (25)
on the connector (26).
3. Install the strainer and plunger valve at the
lower position of pool outlet (marked "+").
From the inside of the pool liner insert the
connector
(26) into one of the pre-cut holes
with the washer remaining on the connector
to be placed against the inside of the liner
wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. With the flat side of the
strainer nut
(24) facing the outside wall of
the liner in a clockwise motion screw the
strainer nut
(24) back onto the threaded
connector
(26) (see drawing 2).
5. Finger tighten the strainer nut (24) onto the
threaded connector
(26).
6. Grasp the plunger valve assembly. Make
sure the step washer (23) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector
(26) (see drawing 3).
8. In a clockwise motion turn the plunger
valve handle to close position. Ensure the
plunger valve is securely closed. This will
prevent water from flowing out during filling
of the pool (see drawing 4).
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP (optional)
2
25 26
INSIDE
LINER WALL
24
1
23
2
1
3
1
2
4
INSIDE
LINER WALL
40

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 7
POOL INLET - NOZZLE & PLUNGER VALVE SETUP (optional)
1. In a counter-clockwise motion unscrew
plunger valve union from the inlet threaded
air connector
(42) (see drawing 5). Be
careful not to lose the step rubber
washer
(23). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut
(24) from the inlet threaded air
connector
(42). Leave the flat washer (25)
on the connector (42).
3. Install the nozzle and plunger valve at the
upper position of pool inlet. From the inside
of the pool liner insert the nozzle union
(27 & 42) into one of the pre-cut holes with
the washer remaining on the connector to
be placed against the inside of the liner
wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. Then, with the flat side
of the strainer nut (24) facing the outside
wall of the liner in a clockwise motion screw
the strainer nut (24) back onto the inlet
threaded air connector (42) (see
drawing 6).
5. Finger tighten the adjustable pool inlet jet
nozzle (27) and the strainer nut (24) onto
the inlet threaded air connector (42).
6. Grasp the plunger valve assembly. Make
sure the step washer (23) is in place.
7. Screw the air jet valve (41) over the inlet
threaded air connector (42).NOTE: Make
sure the air jet valve is securely tighten
and facing up. In a clockwise motion screw
the plunger valve union back onto the inlet
threaded air connector (42) (see
drawing 7).
8. In a clockwise motion turn the plunger valve
handle to close position. Ensure the
plunger valve is securely closed. This will
prevent water from flowing out during filling
of the pool (see drawing 8).
9. Adjust the direction of nozzle head pointing
away from the pool outlet for a better
circulation result
(see drawing 9).
10. The pool liner is now ready to fill with
water. Consult the above-ground-pool
owner’s manual for filling instructions.
5
2
1
7
1
2
8
INSIDE
LINER WALL
9
WATER
FLOW
POOL
6
25 42 27
INSIDE LINER
WALL
24
41

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 8
PRODUCT SPECIFICATIONS
SETUP INSTRUCTIONS
NOTE: NOT SUITABLE FOR USE WITH KCP-LOW -SALT AUTOMATIC SALTWATER SYSTEM
(MODEL 6110/6220).
The sand filter removes suspended particles but does not sanitize your pool. Pool chemistry
is a specialized area and you should consult your local pool service specialist for details.
TOOLS REQUIRED: One (1) Phillips screwdriver
Pump location and mounting:
• The system must be installed on a solid level and vibration-free base.
• Provide a location protected from the weather, moisture, flooding and freezing
temperature.
• Provide adequate access, space and lighting for routine maintenance.
• Pump motor requires free circulation of air for cooling. Do not install the pump in a
damp or non-ventilated location.
A team of 2 or more people is recommended for setting up this product.
The appliance is intended only for household use.
Motor pre-filtering assembly setup:
1. Remove the sand filter and its accessories from the packaging carefully and inspect for any
visible damage.
2. In a counter-clockwise motion unscrew the leaf trap cover (14) from the pre-filter housing.
Take out the basket (16) and filter housing nut (17) (see drawing 10).
3. Connect the pre-filter housing to the motor water inlet. Note: Align the connector in the
pre-filter housing with the water inlet on the motor (see drawing 11).
11
10
35
17
16
14
Model: SF80220RC-1 SF70220RC-1 SF60220RC-1
Power: 220-240 Volt AC 220-240 Volt AC 220-240 Volt AC
Wattage: 250 W 450 W 550 W
Maximum working pressure: 2 bar (30 psi) 2 bar (30 psi) 2 bar (30 psi)
Effective filtering area: 0.07 m2(0.79 ft2) 0.1 m2(1.07 ft2) 0.13 m2(1.44 ft2)
Pump flow rate (at pump outlet): 7.9 m3/h (2100 GPH) 10.5 m3/h (2800 GPH) 12 m3/h (3200 GPH)
Recommended filtering
media quantity: No. 20 silica sand 23 Kg (50 Lbs) or
glass sand 16 Kg
(35 Lbs).
No. 20 silica sand
35 Kg (77 Lbs) or
glass sand 25 Kg
(55 Lbs).
No. 20 silica sand
55 Kg (120 Lbs) or
glass sand 38 Kg
(85 Lbs).
Recommended filtering
media (Not included): No. 20 silica sand or glass sand. Particle size range 0.45 to 0.85 mm (0.018 to 0.033 inches). Uniformity Coefficient less than 1.75.
Limited Warranty: see “Limited Warranty”

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 9
4. In a clockwise motion screw filter housing nut (17) onto the motor water inlet (see
drawings 12.1 & 12.2).
5. Replace the basket (16) and leaf trap cover (14) back to the pre-filter housing (see
drawings 13.1 & 13.2).
SETUP INSTRUCTIONS (continued)
Sand tank installation:
1. Place the tank support base at the selected location.
2. Place the tank on the tank support base (see drawing 14.1).
3. Connect the motor pre-filtering assembly unit to the tank support base (see drawing 14.2).
NOTE: Ensure the pre-filter housing water inlet hose connection is facing towards the pool.
IMPORTANT: Some countries, especially in the European community, require the
product to be secured to the ground or to a base in a permanent upright position.
Check your local authorities to determine if there is a regulation in your area
regarding above-the-ground swimming pool filter-pumps. If yes, then the product
can be mounted to a platform using the two holes located in the base.
See drawing 14.3.
The product can be mounted on a cement base or onto a wooden plat form to prevent
accidental falling over.
• The mounting holes are 6.4 mm in diameter and spaced 100 mm for model
SF80220RC-1 (spaced 115 mm for model SF70220RC-1 & SF60220RC-1) apart.
• Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.
12.1
17
12.2
17
13.213.1
14
16
35
14.1 14.2 14.3
Model SF80220RC-1: 100 mm
Model SF70220RC-1 & SF60220RC-1: 115 mm
19

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 10
SETUP INSTRUCTIONS (continued)
Sand loading:
IMPORTANT: Use No. 20 silica sand or glass sand with particle size range 0.45 to 0.85 mm
(0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75.
Only use the filter media specified by the manufacturer.
NOTE: Before loading the tank with sand, ensure the center pipe hub assembly is
securely in place at the bottom of the tank, and vertically centered inside the tank.
1. Place the sand shield (6) over the top of the center pipe. Pour the sand into the tank at
a slow rate (see drawing 15).
2. Fill the tank approximately half way, remove the sand shield (6) from the top (see
drawing 16).
3. Evenly distribute the sand inside the tank, then fill the tank with some water to provide a
cushioning effect when the remaining sand is poured in. This prevents the center pipe hub
(7) from excessive shock (see drawing 17). Place the sand shield (6) back and continue to
pour the sand into the tank.
4. Sand shall be filled between the “MAX” and “MIN” marked gauge on the center pipe.
Evenly spread and level out the sand by hand (see drawings 17 & 18).
5. Remove the sand shield (6).
6. Wash away all sand around the top edge of the tank.
MAX
MAX
MIN
MIN
MAX
MIN
18
7
15
6
16
6
MAX
MIN
17
7

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 11
6-way valve installation:
1. Lower the 6-way valve over the tank slowly, and ensure the bypass pipe protruding
underneath the 6-way valve fits securely into the center pipe hub (7) top opening
(see drawing 19).
IMPORTANT: There are three hose connection ports on the 6-way valve, ensure the outlet
connection (from filter to the pool) on the valve is facing towards the pool, and the inlet
connection (from motor to valve) is aligned with the motor outlet (see drawing 20).
SETUP INSTRUCTIONS (continued)
WARNING
Improper tank valve and clamp assembly could cause the valve and
clamp to blow off and cause serious injury, property damage or death.
2. Place an L-shape o-ring (11) on the 6-way valve inlet connection and on the pump motor
outlet. In a clockwise motion connect the sand filter interconnecting hose (13) between
the pump motor outlet and the 6-way valve inlet connection (see drawing 21).
3. Remove the clamp bolt, and install the clamp around the tank and 6-way valve flanges,
then replace the clamp bolt and use a phillips screwdriver (not included) to tighten it
(see drawing 22).
20
WATER
INLET
WATER
OUTLET
19
7
21
13
22
4

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 12
SAND FILTER PUMP HOSE CONNECTION SETUP
The 6-way valve has three hose connection ports.
1. Connect one hose (12) end to the pre-filter inlet and the other end of the hose to the lower
plunger valve with the strainer. Ensure the hose nuts are securely tightened.
2. Connect the second hose (12) between the 6-way valve water outlet and the upper plunger
valve with the inlet-nozzle. Ensure the hose nuts are securely tighten.
3. The third hose connection port (drain/waste outlet) on the 6-way valve shall be directed to
a proper draining receptacle using a hose or pipe (not provided). Remove the drain cap
before attaching the drain/waste hose or pipe.
4. The sand filter pump is now ready to filter the pool.
WARNING
• Keep this product more than 3.5m away from the pool.
• Keep the plug of this product more than 4m away from the pool and at a
height of 1.2m at least.
• Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.
(ILLUSTRATION NOT TO SCALE)
According to the International Standard, IEC 60364-7-702, on electrical installation of swimming
pools and other basins equipment, the following installation distances must be respected:
• The filter pump must be positioned more than 3.5m away from the pool walls.
• The power cord plug to the 220-240 volt electrical power source of the filter pump must be
positioned more than 4m away from the pool walls.
Check your local authorities to determine the appropriate standard and requirements for
“electrical installation of swimming pools and basins equipment”. The following table is for
reference only:
International
France
Germany
The Netherlands
Country/Region Standard Number
IEC 60364-7-702
NF C 15-100-7-702
DIN VDE 0100-702
NEN 1010-702
>4M
>3.5M
6-WAY VALVE
WATER
INLET
WATER
OUTLET
MOTOR
MOTOR
WATER
OUTLET PRE-FILTER
WATER INLET
WATER LEVEL
THREADED
STRAINER
CONNECTOR
OUTSIDE
LINER WALL
PLUNGER
VALVE
POWER CORD
L-SHAPE
O-RING
L-SHAPE
O-RING
TO
DRAIN
AIR RELEASE VALVE
RCD
ADJUSTABLE
POOL INLET
JET NOZZLE
AIR JET VALVE
INLET THREADED
AIR CONNECTOR

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 13
SAND FILTER PUMP HOSE CONNECTION SETUP (continued)
For NON-INTEX pool:
Connect the hose (12) to the pool inlet/outlet connection with a large hose clamp. Tighten securely.
POOL
LARGE HOSE
CLAMP
12
3
For INTEX pool with 1-1/4” (32mm) connections/hoses:
Make sure the air jet valve (41) is securely tighten onto the pool inlet air adaptor (43) and facing
up.
44
28
(Adaptor B) 43 41 30 29 31
23 28
(Adaptor B)
23

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 14
OPERATING INSTRUCTIONS
Valve Position Function Water Flow Direction
FILTER
(see drawing 25) Normal filtration and regular vacuuming
of pool From pump through filter media to pool
BACKWASH
(see drawing 26) Reverses water flow to clean filter
media From pump through filter media to valve waste/drain outlet
RINSE
(see drawing 27)
For initial startup cleaning of the sand, and
leveling the sand bed after backwashing
From pump through filter media to
valve waste/drain outlet
WASTE
(see drawing 28) For vacuuming directly to waste,
lowering pool level or to drain the pool From pump to valve waste/drain outlet bypassing the filter media
RECIRCULATE
(see drawing 29) For circulating water back to pool
without going through the filter media From pump through valve to pool bypassing the filter media
CLOSED
(see drawing 30)
Shuts off all flow to filter and pool
“Do not use this setting with pump running”
6-way valve positions and function:
• Risk of electric shock. Connect this product only to a grounding type receptacle protected
by a ground-fault circuit interrupter (GFCI) or residual current device (RCD). Contact a
qualified electrician if you cannot verify that the receptacle is protected by a GFCI/RCD.
Use a qualified electrician to install the GFCI/RCD, which has a maximum rate of 30mA.
Do not use a portable residual current device (PRCD).
•To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or
converter plugs to connect unit to electric supply; provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when your
hands are wet.
• Never operate this product above the maximum working pressure stated on the filter tank.
• Always switch off pump before changing the 6-way valve position.
• Operating this product without water flowing through the system can cause a build up of
hazardous pressure which can result in an explosive situation, serious injury, property
damage or death.
• Never test this pump with compressed air. Never operate the system with water
temperature above 35°C (95°F).
WARNING
RESET
RESET
TEST
TEST
23
RESET
RESET
RESET
TEST
TEST
24
TEST
RCD OPERATING INSTRUCTIONS
• Plug RCD into power outlet. Press RESET button on the RCD plug. Indicator
should be "ON". See FIG. 23.
• Press TEST button on the RCD plug. Indicator should be "OFF". See FIG. 24.
• Press RESET button for use. Do not use if test fails. Contact a qualified
electrician to determine cause of failure.

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 15
Initial startup and operation:
Before operating, be sure that:
• All the hoses have been connected and tightened securely, and correct amount of filter sand
have been loaded.
• The entire system is connected to a grounding type receptacle protected by a ground-fault
circuit interrupter (GFCI) or residual current device (RCD).
OPERATING INSTRUCTIONS (continued)
CAUTION
The filter control valve has a closed position. The pump should never
be on when the valve is in the closed position. If the pump is operated
with the valve closed, explosive situation could exist.
1. Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valves to allow water
to flow into the sand filter pump. With water flowing into sand filter pump, the water pressure will allow the air
trapped inside to escape from the air release valves (19). When all the air has escaped water will flow out of
the valves (19). When this occurs gently finger tighten the valves (19) in a clockwise direction.
IMPORTANT: To prevent air lock, open the lower plunger valve
(connected inlet hose) first and then the upper plunger valve
(connected outlet hose). Open the air release valves, wait until
water starts to flow out of the air release valves, close air release
valves.
2. Ensure the drain/waste outlet on the 6-way valve is not covered and
directed to a proper draining receptacle.
3. BACKWASH - Ensure the pump is off, depress the 6-way valve and
turn it to the “BACKWASH” position (see drawings 26 & 31).
IMPORTANT: To prevent damage to the 6-way valve, always
depress the valve handle before turning. Always switch off pump
before changing the 6-way valve position.
4. Switch on the pump (see drawing 32). Water is circulating backward
through the sand media and to waste/drain outlet.
Backwash until a clear flow of water is observed in the waste/drain
outlet or through the drain sediment window.
NOTE: The initial backwash of the filter is recommended to remove
any impurities or fine sand particles in the sand media.
31
1
2
32
TIMER OFF ON
R
E
T
LI
F
E
S
NI
R
ER
H
S
AW
K
CA
B
ESO
L
C
ETSAW
28
R
E
T
LIF
ESN
I
R
E
TA
L
U
C
R
I
CE
R
H
S
AW
K
C
A
B
E
S
O
L
C
29
R
E
TL
I
F
ETALUC
R
ICER
H
S
AWK
CA
B
ES
O
LC
ETSAW
30
RE
T
L
I
F
E
S
N
I
R
ET
A
L
U
C
RI
C
E
R
E
S
O
LC
ETSA
W
B
25
E
SN
IR
ETALU
C
RICER
HSAW
K
C
A
B
E
S
O
LC
E
TSAW
26
RE
TL
I
F
ES
N
IR
E
TALU
C
RICER
H
SAW
KCAB
ETSA
W
27

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 16
OPERATING INSTRUCTIONS (continued)
5. Switch off the pump, change the 6-way valve to “RINSE” position (see drawing 27).
6. Switch on the pump and run the pump for about one minute to level out the sand bed after
backwashing the sand media.
7. Switch off the pump, change the 6-way valve to “FILTER” position (see drawing 25).
8. Switch on the pump. The system is now operating in the normal filtering mode. Run the pump
until the desired pool water clearance is obtained and no more than 12 hours per day.
9. Record the initial pressure gauge reading when the filter media is clean.
NOTE: During initial setup of the system, it may be necessary to backwash frequently due to
unusual heavy dirt present in the water and sand. After that, as the filter removes dirt and
impurities from the pool water, the accumulated dirt in the sand media will cause the pressure
to rise and the flow to diminish. If there is no vacuuming device attached to the system and
the pressure gauge reading is in the yellow zone it is time to backwash the sand media, see
“BACKWASH” under “initial startup and operation” section.
Vacuuming device (i.e. Intex auto pool cleaner) attached to the system may also cause the
flow to diminish and the pressure to rise. Remove any vacuuming device from the system and
check if the pressure gauge reading has dropped from the yellow zone to the green zone.
10.Monitor the pressure gauge reading, and check that the inlet and outlet openings are not
obstructed on a weekly basis. If the pressure gauge indicates yellow it is time to backwash
the filter media.
Operating the system under “TIMER” mode or manually:
To operate the sand filter pump in “FILTER” mode under “TIMER” control:
A. Set the timer dial to the desired operating hours. See operation time table (see
drawing 33).
B. Turn on the pump by pressing the switch to “ ” position, the sand filter pump is now
filtering the water and will stop after the operating hours are completed. The built-in timer
will now operate for the number of hours selected at the same time each day.
C. Operating hours can be re-adjusted if necessary. Follow step A – B.
To operate the sand filter pump manually (without the “TIMER” mode):
A. Turn on the pump by pressing the switch to “-” position, the sand filter pump is now
filtering the water.
B. To turn off the pump, press the switch to “O” position.
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service
Department for assistance. See separate “Authorized Service Centers” sheet.
33
TIMER OFF ON
TIMER DIAL
(HOURS)

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 17
INTEX POOLS OPERATING TIME TABLE (WITHOUT INTEX SALTWATER SYSTEM)
This table shows the required operating time for average use of the sand filter pump with above
ground pools.
If the system is attached to an “Intex Saltwater System” unit, the filter pump running time
should be longer than the required operating time of the Intex Saltwater System unit.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Sand filter pump operating
time (For one cycle) / (Hours)
(Gals) (Liters) SF80220RC-1 SF70220RC-1 SF60220RC-1
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
457cmx84cm(15'x33") 2587 9792 2
457cmx91cm(15'x36") 2822 10681 2
457cmx107cm(15'x42") 3284 12430 2
457cmx122cm(15'x48") 3736 14141 4
488cmx107cm(16'x42") 3754 14209 4
488cmx122cm(16'x48") 4273 16173 4
488cmx132cm(16'x52") 4614 17464 4
549cmx107cm(18'x42") 4786 18115 4 2 2
549cmx122cm(18'x48") 5455 20647 4 2 2
ROUND
METAL
FRAME POOL
457cmx91cm(15'x36") 3282 12422 2
457cmx107cm(15'x42") 3861 14614 4
457cmx122cm(15'x48") 4440 16805 4
488cmx122cm(16'x48") 5061 19156 4
549cmx122cm(18'x48") 6423 24311 6 4 4
640cmx132cm(21'x52") 9533 36082 6 4 4
732cmx132cm(24'x52") 12481 47241 8 6 6
ULTRA FRAME
POOL
488cmx122cm(16'x48") 5061 19156 4
549cmx122cm(18'x48") 6423 24311 4 4 4
549cmx132cm(18'x52") 6981 26423 6 4 4
610cmx122cm(20'x48") 7947 30079 6 4 4
671cmx132cm(22'x52") 10472 39637 8 4 4
732cmx132cm(24'x52") 12481 47241 8 6 6
792cmx132cm(26'x52") 14667 55515 12 8 8
GRAPHITE GRAY
PANEL POOL
SET™
478cmx124cm(15'8"x49") 4440 16805 4
508cmx124cm(16'8"x49") 5061 19156 4 42
569cmx135cm(18'8"x53") 6981 26423 6 4 4
OVAL FRAME
POOL
305cmx549cmx107cm(10'x18'x42")
2885 10920 2
366cmx610cmx122cm(12'x20'x48")
4393 16628 4 2 2
RECT. ULTRA
FRAME POOL
274cmx457cmx122cm(9'x15'x48")
3484 13187 4 2 2
274cmx549cmx132cm(9'x18'x52")
4545 17203 4 2 2
305cmx610cmx132cm(10'x20'x52")
5835 22085 4 4 2
366cmx732cmx132cm(12'x24'x52")
8403 31805 6 4 4
488cmx975cmx132cm(16'x32'x52")
14364 54368 12 8 6
NOTE: The “12” hours timer setting position has an additional 20 minutes over the actual
setting.

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 18
NON-INTEX POOLS OPERATING TIME TABLE
Water Capacity Sand filter pump operating time (For one cycle) / (Hours)
(Gals) (Liters) SF80220RC-1 SF70220RC-1 SF60220RC-1
3000 11355 2
4000 15140 4 2 2
4440 16805 4 2 2
5000 18925 4 2 2
6000 22710 4 4 2
7000 26495 6 4 4
8000 30280 6 4 4
9000 34065 6 4 4
10000 37850 8 6 4
11000 41635 8 6 4
12000 45420 8 6 6
13000 49205 12 6 6
14000 52990 12 8 6
15000 56775 12 8 6
16000 60560 12 8 8
17000 64345 12 8 8
18000 68130 12 12 8
19000 71915 12 12 8
20000 75700 12 8
21000 79485 12 12
22000 83270 12 12
23000 87055 12 12
24000 90840 12 12
25000 94625 12 12
26000 98410 12 12
This table shows the required operating time for average use of the sand filter pump with above
ground pools.

195
GS
SAVE THESE INSTRUCTIONS
(195GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/18/2017
English
Page 19
MOTOR PRE-FILTER CLEANING AND MAINTENANCE
It is essential to change any damaged element or set of elements as soon as possible.
Use only parts approved by the manufacturer.
1. Make sure the filter pump is switched off, then disconnect the power cord from the electrical
outlet.
2. Turn both plunger valve handles fully clockwise until they stop. This closes the valve, prevents
the water from flowing out of the pool.
3. Release the pressure first by opening the sediment
release valve
(19) located on the lower side of the
pre-filter housing
(see drawing 34).
4. In a counter-clockwise motion unscrew the leaf trap
cover (14), then remove the basket (16) and leaf trap
o-ring
(15) from the pre-filter housing (see drawing 35).
5. Empty and flush the basket using a garden hose, may
use a plastic brush to remove deposits from the basket.
Do not use metal brush.
6. Clean and rinse the inside of the pre-filter housing and the leaf trap O-ring with a garden
hose.
7. Reinstall the leaf trap O-ring, basket and leaf trap cover to the pre-filter housing.
8. Close the sediment release valve (19).
All filter and filter media shall be inspected regularly to ensure that there is no build-up
of debris thus preventing a good filtration. Disposal of any used filter media should be in
accordance with applicable local regulation and legislation.
1
2
34
35
19
14
15
16
35