INVENTOR MOB-GPC12AF User manual

MOBILE AIR CONDITIONER
MOB-GPC12AF

.................................................................................
1
.....................................................................
................................................................................
.............................................................................
18
............................................................................
.................................................................... 20
19
1
2
.................................
..........
16-17
.......................................................................
3-7
8-10
...............
CONTENTS
SUMMARY
WORKING PRINCIPLE
STRUCTURE
OPERATING METHODS
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER
CARE AND MAINTENANCE
TROUBLESHOOTING
USER NOTICES
AFTER SERVICE
.............................................................
................................................................
OPERATIONOF THE REMOTE CONTROLLER
11-12
13-15
ACCESSORIES AND INSTALLATION OF HEAT EXHAUST HOSE
CIRCUIT DIAGRAM 21
....

SUMMARY
-1-
INVENTOR MOBILE AIR CONDITIONER is a small, moveable air conditioner. It possess
the functions of COOL, DRY and the Separate Ventilation, and depends on different places,
it can be moved as will. It is fit for home and office use, especially fit for the house with many
rooms. With the compact configuration, excellent workmanship, elegant appearance, it is
convenient for moving,energy saving, and low noise.
Note: Please read this manual carefully before operating the unit, the manual is used for
reference, and the technical parameters are subject to change without notice.
WORKING PRINCIPLE
With the help of upper motor, the airflow of indoor passes through the evaporator becomes the
cooling wind, but with the help of lower motor, the airflow of indoor passes through the condenser
becomes the heating wind. It was designed two duct systems in its structure The heating wind is discharged
by the rear outlet, the cooling wind is discharged by the front outlet, flow-guided by the louver, and it
brings the gentle cooling airflow, and the low temperature environment is maintained.
The Working Principle
Cooling wind
Upper motor
Lower
motor
Evaporator
Airflow 1
Airflow 2
Capillary
Heating wind
Condenser

－2－
STRUCTURE
Front
Rear
Air outlet
Controller panel
Handle
Remote box
Upper air inlet grille
Air exhaust outlet
Lower air inlet grille

50cm
50cm
The working range of COOL mode and HEAT modeis16℃-
30℃
At DRY mode,the static pressure range is 0～25 pa.
When operating, the unit should be placed on the horizontal place, more
than 50cm away from the wall or other obstructions.
The working range of COOL
mode,Heat mode and DRY
mode.
Location requirement
Power supply Before the unit is power-on, please check the following:
The power supply is rated voltage ±10%.
The power plugs and the sockets can be supported by the current
that is more than 16A.
The thread section of the lead wires and any continued use lead wire
is no less than 1.5mm2.
The air conditioner must be safety earthed. Earth wire must be
connected to the special device of the building. In order to provide
the good earthing for the air conditioner.
The appliance must be positioned so that the plug is accessible,
If the supply cord is damaged, it must be replaced by the manufacturer
or its service agent or a similarly qualified person in order to avoid a hazard.
The appliance shall not be installed in the laundry.
The minimum clearance from the appliance to combustible surface is 50cm.
When children use the appliance, it must be supervised by adults or supervisors.
Including an air switch with suitable capacity, please note the following table. Air switch
should be included magnet buckle and heating buckle function, it can protect the
circuit-short and overload. (Caution: please do not use the fuse only for protect the circuit)
The appliance shall be installed in accordance with national wiring regulations.
The appliance is for indoor use only.
°
F
°
F
12K 16A
Air switch capacityAir-conditioner (W)
OPERATING METHODS
-3-
.

OPERATING METHODS
● Can not use the steel wire or the brass wire replace the fuse, the
capability of the fuse must be appropriate. In order to avoid the power
cord damaged and electrical leakage, do not fix the power supply on the
knife edge or the sharp object.
● The wiring must be operated by the professional and according
to the national regulations.
－4－

-5-
OPERA TING METHODS
Control paneland the function
1."ON/OFF"key
Press once to start and press once more to stop the unit.
2."MODE" key
Press this button to change the operation mode in order of:
LOOC → DRY→ FAN→ HEAT(No Heat mode for the cooling only unit.)
3. key
In "COOL"and "HEAT" mode,press
"
" once, the SET TEMP. will decrease 1
" once, the SET
TEMP.
"
"
will increase 1 The SET TEMP. can
be selected from 16℃(61 )～30℃(86 ).
Press. " ℃(1 )
°
F
℃(1 ),
°
F
°
F° F
WATE full
ON/OFFkey
MODEkey
COOL mode
Set TEMP.
DRY mode
FAN mode
key
" "" "
→ COOL
""
I1M-12

-6-
OPERATING METHODS
1). To select a place near the door and window, install the exhaust duct.
2). Press"MODE"key to select"COOL"mode.
3).Press key to set the suitabletemp.16℃(61 )～30 86
℃.
When the unit is running in the COOL mode, in order to keep the good cooling effect,
please paymore attention to:
If there is thedirect sunlight near the window, please use the curtain to shield.
conditioner room.
Please close the door and window, in order to obtain the better dehumidifying effect:
Press"MODE" key, select the "DRY" mode, the unit will run in the "DRY" mode, at the
same time, the upper motor is running at the low speed, it is not adjustable.
COOL mode
CAUTION
DRY mode
When in COOL or DRY mode, the dew water will drain into the tank.
When the tank gets full, the indicator will flash, and the buzzer will sound eight times,
LED window shows error code “H8”,at the same time the unit stop running.
WATER
DRAINAGE
"
"""°F°F
℃(61 )～30 86
℃.
°F°F
1). Press"MODE"key toselect "HEAT"mode.
2).Press key to setthe suitabletemp.16
HEAT mode "
"""
When the unit running in cool mode,do not use other heat sources in the air
Drain cap
Drain port
Install Drain Hose
1.Remove drain cap from drain port.
Drain Cap
2. Attach one end of the drain hose to the drain port with the clamp. See Drain Hose graphic.
3. Insert the drain plug into the other end of the drain hose and secure with clamp. See Drain Hose graphic.
4. Attach the drain hose clip to the back panel of the air conditioner near the drain port with the screw
provided.
Installof drainage hose (as shown in following figure):
Note Drainage hose must be installed before using otherwise block of drain may occur and
affects normal run of unit.
Drain Hose included:
Drainage pipe Clamp Pipe clip Rubber plug Screw
When COOL or DRY is running, condensate will drain to water tank.When water tank is fillbuz-
er will sound 8 timers for warn,water tank green indicated light on panel on with H8 displayed on
fro-m fixing clamp,then drain out water in tank.After that,plug the pipe plug onto pipe to prevent
leaka-ge of condensate and fix drainage pipe fixing clamp as shown in following figure.The unit
will resume running when water filled protect released and compressor stops for 3 minutes.
display window and whole unit stop running.Plug out plug on drainage hose and take off the hose

5. Snap the free end of the drain hose into the drain hose clip.
Drain Hose
Drain Hose Clip
Drain port
fixed clamp with screw
Drain plug
clip clip
drain hose
-7-
OPERATING METHODS

- -
●
AUTO
COOL
DRY
FAN
HEAT
FAN FAN speed button
Press this button once, fan speed will change
as below: Auto
Low speed Middle speed
High speed
Note:Under the Dry mode, the fan speed isn't
●
Simpleness swing mode is defaulted for wireless
remote control, in this mode, press this button,
(＋/－)
16 ～30℃
●
Note: Be sure that there are no obstructions between receiver and remote control; Don't drop
or throw the remote control; Don't let any liquid in the remote control and put the remote control
directly under the sunlight or any place where is very hot
.
Signal transmitter
Remote control
ON/OFF
ON/OFF button
Press this button, the unit will be started or stopped,
which can clear the timer or sleeping function of
last time.
●
.PMET button
(＋/－)
When press +button , the setting temp. will b e
increasedby1 (1 ),When press-button,the
setting temp. will be decreased by 1
The temp. will be changed quickly
the button continuously and setting temp. range
℃
is
by pressing
●
●
●
Swing up and down button
℃
below.
Press this button, the running mode will change as
Mode button
MODE
could turn on or turn off the Up and down
swing function.
When unit is turned off, synchronously press
"+" and Up and down swing buttons, it could
be switched between the simpleness swing
mode and stationary swing mode, at this time,
blinks 2 seconds.
In Stationary swingmode,pressthis button,the
angleforUpanddown swing as showinbelow:
Whenup anddownswing louverisworking,
whenturn offtheunit, thesiwnglouver will
●
immediatelystopat currentposition.
showsupand downswinglouverswings back
andforth as showintheabove figure.
adjustable, low fan speed is imperative,
but whenoperating thisbutton,thewireless
remote control will send this signal.
NAMES AND FUNCTIONS OFTHE REMOTE CONTROLLER
°F(1 )
°F
℃°F°F
FAN
AUTO
OPER
HEALTH
AIR
FILTER
TURBO
ON/OFF
X-FAN
HOUR
HUMIDITY
ON/OFF
MODE
FAN
X-FAN
TURBO
TEMP TIMER
SLEEP LIGHT
signal of heating operation.
)
(Note:no for coolling only unit As for
cooling only unit, it won’t have
any action when it receives the
8