involight BEE1915 User manual

19x15W Bee eye moving LED
BEE1915

1. Unpacking
Thank you for choosing our lighting. For your own safety, please read this manual before
installing the device. This manual covers the important information on installation and
applications. Please install and operate the fixture with following instructions. Meanwhile,
please keep this manual well for future needs.
This fixture is made of a new type of high temperature strength of engineering plastics
and cast aluminum casing with nice outlook. The fixture is designed and manufactured
strictly following CE standards, complying with international standard DMX512 protocol.
It’s available independently controlled and linkable with each other for operation. And it is
applicable for large-scale live performances, theater, studio, nightclubs and discos.
4-IN-1 LEDs(RGBW) which features high brightness and stability. Please carefully
unpack it when you receive the fixture and check whether it is damaged during the
transportation. And please check whether the following items are included inside the box:
Moving Head---------One Signal Cable----One
Hanging Bracket-----Two Power Cable----One
Safety Cable---------one User Manual----One
2. Safety Instructions
This device has left the factory in perfect condition. In order to maintain this condition and
to ensure a safe operation, it is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes,
do not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be
earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be
the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does
not necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance

with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat
radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order to
avoid a hazard.
3. Operation Instructions
The moving head is for wash effect for on-site decoration purpose.
Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes. So
make sure to operate the fixture until it is in normal temperature.
This light should be keep away from strong shaking during any transportation or
movement.
Don’t pull up the light by only the head, or it might cause damages to the mechanical
parts.
Don’t expose the fixture in overheat, moisture or environment with too much dust when
installing it. And don’t lay any power cables on the floor. Or it might cause electronic
shock to the people.
Make sure the installation place is in good safety condition before installing the fixture.
Make sure to put the safety chain and check whether the screws are screwed properly
when installing the fixture.
Make sure the lens are in good condition. It’s recommended to replace the units if there
are any damages or severe scratch.
Make sure the fixture is operated by qualified personnel who knows the fixture before
using.
Keep the original packages if any second shipment is needed.
Don’t try to change the fixtures without any instruction by the manufacturer or the
appointed repairing agencies.
It is not in warranty range if there are any malfunctions from not following the user manual
to operate or any illegal operation, like shock short circuit, electronic shock, lamp broke,
etc.
4. Mounting and Installation
Cautions: For added protection mount the fixtures in areas outside walking paths, seating
areas, or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as
an appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture
from a
periodic safety inspection of all installation material and the fixture. If you lack these
qualifications, do not attempt the installation yourself. Improper installation can result in
bodily injury.

Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.
Clamp Mounting: The light provides a unique mounting bracket assembly that integrates
the bottom of the base, the included “Omega Bracket,” and the safety cable rigging point
in one unit (see the illustration below). When mounting this fixture to truss be sure to
secure an appropriately rated clamp to the included omega bracket using a M10 screw
fitted through the center hole of the “omega bracket”. As an added safety measure be sure
to attached at least one properly rated safety cable to the fixture using on of the safety
cable rigging point integrated in the base assembly
Regardless of the rigging option you choose for your 19pcs zoom, always be sure to
secure your fixture with a safety cable. The fixture provides a built-in rigging point for a
safety cable on the hanging bracket as illustrated above. Be sure to only use the
designated rigging point for the safety cable and never secure a safety cable to a carrying
handle

5. DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the
other side to the male 3-pin XLR input of the moving head. You can chain multiple
Moving heads be connected together through serial linking. The cable needed should be
two core, screened cable with XLR input and output connectors. Please refer to the
diagram below.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically
noisy environment, such as in a discotheque, it is recommended to use a DMX terminator.
This helps in preventing corruption of the digital control signal by electrical noise. The
DMX terminator is simply an XLR plug with a 120 Ωresistor connected between pins 2
and 3,which is then plugged into the output XLR socket of the last fixture in the chain.
Please see illustrations below.
1
2
3
PIN 3
PIN 2
120Ω

6. Product Introduction

7. Display instruction

8. Product parameters
Voltage: AC100V～240V 50-60HZ
LED Source: 19x15W high power RGBW 4 in 1 LEDs
Zoom: 4-60°
Strobe: 0-20Hz
With CTO color temperature adjustment
Control Mode: DMX512,Sound-actived,Master/slave Auto, RDM
DMX Channels: 21 CH/23 CH/35 CH/78 CH/92 CH/97 CH/99 CH
Dimmer: 0-100% linear dimmer And16bit dimmering
The lens can be rotated in both directions, and the speed can be adjusted
Pan: 540°+16 bit fine Tilt: 270°+16 bit fine
Display: LCD colorful display
Features
1. Each LED can be controlled individually. Unique honeycomb design lens
2. The front lens can be rotated forward and reverse without limit, creating amazing effects
3. The display screen can be automatically flipped 180° to adapt to the installation in
different positions
4. Can be used as beam, wash or effect light (kaleidoscope effect)
5. The scanning position can be memorized, and it will automatically reset after rotation
without expected movement.
6. Smart fan cooling (the fan will change speed as the temperature changes).
Temperature detection system (if the temperature detection is wrong, the light will stop
working to protect the fixture)
7. Automatic error correction and error reporting function
9. lighting size

10. DMX Channels
21 CH
CH
Function
DMX Value
Details
1
Red
0-255
Red dimmer
2
Red Fine
0-255
Red fine control
3
Green
0-255
Green dimmer
4
Green Fine
0-255
Green fine control
5
Blue
0-255
Blue dimmer
6
Blue Fine
0-255
Blue fine control
7
White
0-255
White dimmer
8
White Fine
0-255
White fine control
9
CTO
0-255
Color temperature linear control
10
Macro color
0-255
Marco color control
11
strobe
0-3
Light up
4-203
Strobe with the same step from slow to fast
204-255
Random strobe
12
Dimmer
0-255
0-100 linear dimmer from dark to bright
13
Dimmer Fine
0-255
Dimmer fine control
14
Pan
0-255
Pan movement control
15
Pan Fine
0-255
Pan fine control
16
Tilt
0-255
Tilt movement control
17
Tilt Fine
0-255
Pan fine control
18
Function
0-255
19
Reset
0-250
No function
251-255
Reset with 5 seconds
20
Zoom
0-255
21
Zoom Rotation
0-127
0 to 60 degree
128-191
Unlimited clockwise rotation from fast to slow
192-255
Unlimited anticlockwise rotation from fast to slow
23 CH
CH
Function
DMX Value
Details
1
Pan
0-255
Pan movement control
2
Pan fine
0-255
Pan fine control
3
Tilt
0-255
Tilt movement control
4
Tilt fine
0-255
Pan fine control
5
Pan/Tilt speed
0-255
Speed from fast to slow
6
ZOOM
0-255
Zoom
7
LENS rotation
0-127
0 to 60 degree

128-191
Unlimited clockwise rotation from fast to slow
192-255
Unlimited anticlockwise rotation from fast to slow
8
Dimmer
0-255
0-100 linear dimmer from dark to bright
9
Strobe
0-3
Light up
4-203
Strobe with the same step from slow to fast
204-255
Random strobe
10
R
0-255
1-100% Red linear dimmer from dark to bright
11
G
0-255
1-100% Green linear dimmer from dark to bright
12
B
0-255
1-100% Blue linear dimmer from dark to bright
13
W
0-255
1-100% White linear dimmer from dark to bright
14
Color
temperature
0-255
Linear color temperature control
15
Marco
0-255
Marco color change
16
Static effect
0-255
Each 5 DMX value is a kind of static effect
17
Dynamic effect
0-255
Each 5 DMX value is a kind of dynamic effect
18
Dynamic effect
speed
0-255
Speed from slow to fast,pls operate against 15
CH
19
Background R
0-255
1-100% Background Red linear dimmer from
dark to bright
20
Background G
0-255
1-100% Background Blue linear dimmer from
dark to bright
21
Background B
0-255
1-100% Background Green linear dimmer from
dark to bright
22
Background W
0-255
1-100% Background Blue linear dimmer from
dark to bright
23
Reset
0-250
No function
251-255
Reset with 5 seconds
35CH
CH
Function
DMX Value
Details
1
Red
0-255
Red dimmer
2
Red Fine
0-255
Red fine control
3
Green
0-255
Green dimmer
4
Green Fine
0-255
Green fine control
5
Blue
0-255
Blue dimmer
6
Blue Fine
0-255
Blue fine control
7
8
White
White Fine
0-255
White dimmer
8
White Fine
0-255
White fine control
9
CTO
0-255
Color temperature linear control
10
Macro colour
0-255
Marco color control
11
strobe
0-3
Light up
4-203
Strobe with the same step from slow to fast
204-255
Random strobe
12
Dimmer
0-255
0-100 linear dimmer from dark to bright
13
Dimmer Fine
0-255
Dimmer fine control
14
Pan
0-255
Pan movement control

15
Pan Fine
0-255
Pan fine control
16
Tilt
0-255
Tilt movement control
17
Tilt Fine
0-255
Pan fine control
18
Function
0-255
19
Reset
0-250
No function
251-255
Reset with 5 seconds
20
Zoom
0-255
21
Zoom Rotation
0-127
0 to 60 degree
128-191
Unlimited clockwise rotation from fast to slow
192-255
Unlimited anticlockwise rotation from fast to slow
22
Shape
Selection
0-255
Selecting shape
23
Shape Speed
0-255
Shape speed control
24
Shape Fade
0-255
Shape fade
25
Shape R
0-255
Shape in Red color
26
Shape G
0-255
Shape in Green color
27
Shape B
0-255
Shape in Blue color
28
Shape W
0-255
Shape in White color
29
Shape Dimmer
0-255
Shape dimmer 0-100%
30
Background
Dimmer
0-255
Background dimmer 0-100%
31
Shape
Transition
0-255
Shape change
32
Shape Offset
0-255
Shape offset
33
Foreground
strobe
0-255
Foreground strobe control
34
Background
strobe
0-255
Background strobe control
35
Background
selection
0-255
Background selection
78CH
CH
Function
DMX Value
Details
1
Red
0-255
Red dimmer
2
Red Fine
0-255
Red fine control
3
Green
0-255
Green dimmer
4
Green Fine
0-255
Green fine control
5
Blue
0-255
Blue dimmer
6
Blue Fine
0-255
Blue fine control
7
White
0-255
White dimmer
8
White Fine
0-255
White fine control
9
CTO
0-255
Color temperature linear control
10
Macro colour
0-255
Marco color control
11
strobe
0-3
Light up
4-203
Strobe with the same step from slow to fast

204-255
Random strobe
12
Dimmer
0-255
0-100 linear dimmer from dark to bright
13
Dimmer Fine
0-255
Dimmer fine control
14
Pan
0-255
Pan movement control
15
Pan Fine
0-255
Pan fine control
16
Tilt
0-255
Tilt movement control
17
Tilt Fine
0-255
Pan fine control
18
Function
0-255
19
Reset
0-250
No function
251-255
Reset with 5 seconds
20
Zoom
0-255
21
Zoom Rotation
0-127
0 to 60 degree
128-191
Unlimited clockwise rotation from fast to slow
192-255
Unlimited anticlockwise rotation from fast to slow
22
Red dimmer 1
0-255
LED 1 red dimmer
23
Green dimmer 1
0-255
LED 1 green dimmer
24
Blue dimmer 1
0-255
LED 1 blue dimmer
25
Red dimmer 2
0-255
LED 2 red dimmer
26
Green dimmer 2
0-255
LED 2 green dimmer
27
Blue dimmer 2
0-255
LED 2 blue dimmer
……
………
………
………
…
………
………
………
76
Red dimmer 19
0-255
LED 19 red dimmer
77
Green dimmer
19
0-255
LED 19 green dimmer
78
Blue dimmer 19
0-255
LED 19 blue dimmer
92CH
CH
Function
DMX Value
Details
1
Red
0-255
Red dimmer
2
Red Fine
0-255
Red fine control
3
Green
0-255
Green dimmer
4
Green Fine
0-255
Green fine control
5
Blue
0-255
Blue dimmer
6
Blue Fine
0-255
Blue fine control
7
White
0-255
White dimmer
8
White Fine
0-255
White fine control
9
CTO
0-255
Color temperature linear control
10
Macro colour
0-255
Marco color control
11
strobe
0-3
Light up
4-203
Strobe with the same step from slow to fast
204-255
Random strobe
12
Dimmer
0-255
0-100 linear dimmer from dark to bright
13
Dimmer Fine
0-255
Dimmer fine control

14
Pan
0-255
Pan movement control
15
Pan Fine
0-255
Pan fine control
16
Tilt
0-255
Tilt movement control
17
Tilt Fine
0-255
Pan fine control
18
Function
0-255
19
Reset
0-250
No function
251-255
Reset with 5 seconds
20
Zoom
0-255
21
Zoom Rotation
0-127
0 to 60 degree
128-191
Unlimited clockwise rotation from fast to slow
192-255
Unlimited anticlockwise rotation from fast to slow
22
Shape
0-255
Selecting shape
23
Shape Speed
0-255
Shape speed control
24
Shape Fade
0-255
Shape fade
25
Shape R
0-255
Shape in Red color
26
Shape G
0-255
Shape in Green color
27
Shape B
0-255
Shape in Blue color
28
Shape W
0-255
Shape in White color
29
Shape Dimmer
0-255
Shape dimmer 0-100%
30
Background
0-255
Background dimmer 0-100%
31
Shape
0-255
Shape change
32
Shape Offset
0-255
Shape offset
33
Foreground
0-255
Foreground strobe control
34
Background
0-255
Background strobe control
35
Background
0-255
Background selection
36
Red dimmer 1
0-255
LED 1 red dimmer
37
Green dimmer 1
0-255
LED 1 green dimmer
38
Blue dimmer 1
0-255
LED 1 blue dimmer
39
Red dimmer 2
0-255
LED 2 red dimmer
40
Green dimmer 2
0-255
LED 2 green dimmer
41
Blue dimmer 2
0-255
LED 2 blue dimmer
……
………
………
………
…
………
………
………
90
Red dimmer 19
0-255
LED 19 red dimmer
91
Green dimmer
0-255
LED 19 green dimmer
92
Blue dimmer 19
0-255
LED 19 blue dimmer
97CH
CH
Function
DMX Value
Details
1
Red
0-255
Red dimmer
2
Red Fine
0-255
Red fine control
3
Green
0-255
Green dimmer
4
Green Fine
0-255
Green fine control
5
Blue
0-255
Blue dimmer
6
Blue Fine
0-255
Blue fine control

7
White
0-255
White dimmer
8
White Fine
0-255
White fine control
9
CTO
0-255
Color temperature linear control
10
Macro colour
0-255
Marco color control
11
strobe
0-3
Light up
4-203
Strobe with the same step from slow to fast
204-255
Randon strobe
12
Dimmer
0-255
0-100 linear dimmer from dark to bright
13
Dimmer Fine
0-255
Dimmer fine control
14
Pan
0-255
Pan movement control
15
Pan Fine
0-255
Pan fine control
16
Tilt
0-255
Tilt movement control
17
Tilt Fine
0-255
Pan fine control
18
Function
0-255
19
Reset
0-250
No function
251-255
Reset with 5 seconds
20
Zoom
0-255
21
Zoom Rotation
0-127
0 to 60 degree
128-191
Unlimited clockwise rotation from fast to slow
192-255
Unlimited anticlockwise rotation from fast to slow
22
Red dimmer 1
0-255
LED 1 red dimmer
23
Green dimmer 1
0-255
LED 1 green dimmer
24
Blue dimmer 1
0-255
LED 1 blue dimmer
25
White dimmer 1
0-255
LED 1 white dimmer
……
………
………
………
…
………
………
………
94
Red dimmer 19
0-255
LED 19 red dimmer
95
Green dimmer
19
0-255
LED 19 green dimmer
96
Blue dimmer 19
0-255
LED 19 blue dimmer
97
White dimmer
19
0-255
LED 19 white dimmer
99CH
CH
Function
DMX Value
Details
1
Pan
0-255
Pan movement control
2
Pan fine
0-255
Pan fine control
3
Tilt
0-255
Tilt movement control
4
Tilt fine
0-255
Pan fine control
5
Pan/Tilt speed
0-255
Speed from fast to slow
6
ZOOM
0-255
Zoom
7
LENS rotation
0-127
0 to 60 degree
128-191
Unlimited clockwise rotation from fast to slow

192-255
Unlimited anticlockwise rotation from fast to
slow
8
Dimmer
0-255
0-100 linear dimmer from dark to bright
9
Strobe
0-3
Light up
4-203
Strobe with the same step from slow to fast
204-255
Random strobe
10
Red
0-255
1-100% Red linear dimmer from dark to
bright
11
Green
0-255
1-100% Green linear dimmer from dark to
bright
12
Blue
0-255
1-100% Blue linear dimmer from dark to
bright
13
White
0-255
1-100% White linear dimmer from dark to
bright
14
CTO
0-255
Linear color temperature control
15
Marco
0-255
Marco color change
16
Static effect
0-255
Each 5 DMX value is a kind of static effect
17
Dynamic effect
0-255
Each 5 DMX value is a kind of dynamic effect
18
Dynamic effect
speed
0-255
Speed from slow to fast, pls operate against
15 CH
19
Background R
0-255
1-100% Background Red linear dimmer from
dark to bright
20
Background G
0-255
1-100% Background Blue dimmer from dark
to bright
21
Background B
0-255
1-100% Background Green dimmer from
dark to bright
22
Background W
0-255
1-100% Background Blue dimmer from dark
to bright
23
Reset
0-250
No function
251-255
Reset with 5 seconds
24
Red dimmer 1
0-255
LED 1 red dimmer
25
Green dimmer 1
0-255
LED 1 green dimmer
26
Blue dimmer 1
0-255
LED 1 blue dimmer
27
White dimmer 1
0-255
LED 1 white dimmer
……
………
………
………
…
………
………
………
96
Red dimmer 19
0-255
LED 19 red dimmer
97
Green dimmer
19
0-255
LED 19 green dimmer
98
Blue dimmer 19
0-255
LED 19 blue dimmer
99
White dimmer 19
0-255
LED 19 white dimmer

11.Illumination data:
LUX Data of 4 degree beam angle:
R 83700LUX@2.5m 2550LUX@5m 1150[email protected]
G 13800LUX@2.5m 3800LUX@5m 1780LUX@7.5m
B [email protected]m 4460LUX@5m [email protected]
W [email protected]m 5300LUX@5m [email protected]
RGBW 50400[email protected] 15500LUX@5m 6680LUX@7.5m
10. Maintenance and Cleaning
The following points have to be considered during the inspection:
1. All screws for installing the devices or parts of the device have to be tightly connected
and must not be corroded. 2. There must not be any deformations on the housing, color
lenses, fixations and installation spots (ceiling, suspension, trussing) . 3. Mechanically
moved parts must not show any traces of wearing and must not rotate with unbalances. 4.
The electric power supply cables must not show any damage, material fatigue or
sediments.
Further instructions depending on the installation spot and usage have to be adhered by a
skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a regular
cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakeness of the lights due
to accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make sure
that the circuit contacts are in good condition, prevent the poor contact of circuit from
overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth.
Never use alcohol or solvents. There are no serviceable parts inside the device. Please
refer to the instructions under“Installation instructions”. Should you need any spare parts,
please order genuine parts from your local dealer