Ioimage trk-101 User manual

QuickInstallGuide
trk‐101andtrk‐101‐PAnalyticIPEncoders
1.FromtheLiveViewwindow,accesstheCamera
SetupbyclickingSetup>Camera>Streaming.
2.IntheVideoStandardbox,selecttherequired
videoformat(PAL/NTSC).Bydefault,NTSCisthe
defaultVideoStandardselection.
Oncethestandardhasbeenselected,confirmthat
otherpredefinedsettingswillbedeleted.
3.Whencompleted,clickApplytosavesettings.
1.FromtheSetup>Camera>Type&Modelscreen,selectPan/Tilt/Zoom(PTZ).
2.Selectthecameramodelandcommunicationdetailsfromthedrop‐downlists.
Formoreinformation,seesection5.3.1.2.1intheHTMLEditionUnitsUser’sGuide.
3.ClickStartPTZSetuptorunthewizardtoconfigurePTZsettings.Formore
information,seesection5.3.1.2.1.1intheUser’sGuide.
4.Whencompleted,clickApplytosavesettings.
trk‐101
trk‐101‐P
trk‐101/trk‐101‐P
Network(Ethernet)
Camera/VideoSource
Properlyratedpowersupply
1.ClicktheDNAiconandruntheDNAutility(DNA.exe).
DNAdiscoversalldevicesonthenetwork.
2.Ifthereareauthenticateddevices,ontheDNAtoolbar,clicktheLogin
iconandenterlogincredentialsforthedevices.

3.IftherearedeviceslocatedonaseparateVLAN,addthemmanually
byclickingontheDNAtoolbar.
4.Entertheunit’sdefaultIPaddressinyourbrowser.
5.WhentheLoginwindowopens,enterthedefaultusernameand
password.

Warning:THISGUIDEISFORDEMONSTRATIONPURPOSESONLY.Fordeploymentinliveapplications,suchassecurity,safetyandlossprevention
programs,installers,ownersandusersshouldreadandfollowtheprescribedproceduresprovidedintheinstallationmanualanduser’sguide.
Installationshouldfollowsafety,standards,electricalcodesandsecuritybestpracticesaswellasthelawsthatapplywheretheunitsarebeinginstalled.
Notice:Failureinpartorinwholeoftheinstaller,owner,oruserinanywaytofollowtheprescribedproceduresortoheedwarningsandcautions
providedintheinstallationandusermanualshallabsolveDVTELanditsagentsfromanyresultingliability.
P/NMA0605‐20‐65
trk‐101_101‐P_QIG_Nov19_14
DVTEL, Inc. 65 Challenger Road Ridgefield Park, NJ 07660
Tel: [phone] Fax: [phone] Order Fax: [phone]
[email protected] www.dvtel.com
1.SelecttheLiveViewtab.
2.SelectArm.Thecameraisarmedandreadytouse.The
labeloftheArmbuttonisrenamedDisarm.
FromtheSetuptab,selectAnalytics>Rules.
Arulefordetectinghumansorvehiclesenteringthe
scene(bluemaskedarea)isdefinedbydefault.
Youcanactivaterules,modifysettings,delete,or
addanewrule.
Tocreateanewrule,foreachpreset:
1.ClickNew.
2.Selecttheruletype.
3.Drawonthevideoscenewhereyouwantthe
detectiontotakeplace.
4.Definetheattributesfordetection.
5.Whenfinished,clickApplytosavethesettings.
1.Foreachpreset,fromtheLiveViewwindow,selectSetup>
Analytics>Depth>SoloSetup.Thefollowinginstructionsare
displayedonthescreen.
2.OntheSoloSetupcontrolkeypad,clicktheStartRecordingicon
andselectafolderwheretostoretheclip.
3.PressStopRecording.
4.ProceedtothetabforStep1:Ground&Heighttoplaceground
andheightmarkersandguidelinesintheclip.
5.ClickBrowsetoloadandviewtheclip.Navigatetheclipandadd
humanmarkers.
6.ExitClipmodeandreturntoLivemodebypressingtheroundPlay
buttononthecontrolpanellocatedtotheleftofthemonitor.
ContinuesettingdepthbyproceedingtothetabsforSteps2‐4.
Followtheon‐screeninstructions.ExpandtheHelpsectionincluded
witheachstepfordetailedinformation.
Verifythatthesettingsprovideanaccuraterepresentationofthe
sizesanddistancesinthescene.
Whenfinished,clickApplytosavesettings.