IP Camera 3-AXIS User manual

1/42
User Manual
CMOS 2.0 Mega Pixel
3-AXIS IP Dome Camera

2/42
WARINGS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MISTURE.
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION：TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
COPYRIGHT
THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED
TO THEIR RESPECTIVE COMPANIES.

3/42
Content
I. PREFACE....................................................................................................................................... 4
II. PRODUCT SPECIFICATIONS....................................................................................................... 4
III. PRODUCT INSTALLATION ........................................................................................................... 6
A. MONITOR SETTING..................................................................................................................................... 6
B. HARDWARE INSTALLATION AND I/O PIN ASSIGNMENT............................................................................... 7
C. IPASSIGNMENT ....................................................................................................................................... 11
D. INSTALL ACTIVEXCONTROL:................................................................................................................... 13
IV. LIVE VIDEO.................................................................................................................................. 15
V. CONFIGURATION........................................................................................................................ 17
A. SYSTEM ................................................................................................................................................... 18
B. NETWORK ................................................................................................................................................ 22
C. A/V SETTING ........................................................................................................................................... 26
D. EVENT LIST.............................................................................................................................................. 32
VI. NETWORK CONFIGURATION .................................................................................................... 39
VII. FACTORY DEFAULT ................................................................................................................... 41
VIII. PACKAGE CONTENTS ............................................................................................................... 41
APPENDIX I .......................................................................................................................................... 42
V1.1_111229

4/42
I. Preface
3-Axis IP Dome is a professional CMOS Mega Pixel IP Dome. It has built-in web
server which enables user to view real-time video via IE browser. It also supports
simultaneously H.264/JPEG/ MPEG4 (3GPP Only) video compression with CMOS
M-Pixel Sensor which provides smooth and high video quality. The video can be
stored in the SD card, and can be playback remotely.
3-Axis IP Dome is an easy-to-use IP Camera which is designed for security
application.
II.Product Specifications
zSupport Video out
z2M CMOS Sensor
zPower over Ethernet available
z3-Axis Gimbal Adjustments
zH.264/ JPEG/ MPEG4 (3GPP only) compression
zSD card backup
z2-way audio
zSupport Cell Phone/PDA/3GPP
zSDK for Software Integration
zFree Bundle 36 ch Recording Software
Specifications
Hardware
CPU ARM 9 ,32 bit RISC
RAM 256MB
Flash 16MB
Image sensor 1/3” 2M CMOs sensor
Lens Type 1.47mm Fish Eye Lens
FOV 195°
I/O 1 in/ 1 Relay Out
Video Out x1

5/42
Audio In x1
Audio Out x1
Power over Ethernet Yes (Optional)
Power Consumption DC 12V 470mA
Dimensions ∮132 * H 108.4
Network
Ethernet 10/ 100 Base-T
Network Protocol HTTP, TCP/ IP, SMTP, FTP, PPPoE, DHCP, DDNS, NTP,
UPnP, 3GPP
System
Video Resolution
1600x1200, 1280x1024, 1280x960,1280x720,
800x600,640x480, 320x240, 176x144
Video Adjust Brightness, Contrast, Sharpness, BLC, Night Mode
Triple Streaming Yes
Image Snapshot Yes
Full Screen Monitoring Yes
Privacy Mask Yes, 3 different areas
Compression Format H.264/ JPEG/ MPEG4 (3GPP only)
Video Bitrates Adjust CBR, VBR
Motion Detection Yes, 3 different areas
Triggered Action Mail, FTP, Save to SD card, Relay
Pre/ Post Alarm Yes, configurable
Security Password protection
Firmware Upgrade HTTP mode, can be upgraded remotely
Simultaneous Connection Up to 10
Audio Yes, 2-way
SD card management
Recording Trigger Motion Detection, IP check, Network break down (wire
only),schedule, alarm
Video Format AVI, JPEG
Video Playback Yes
Delete Files Yes
Web browsing requirement
OS Windows 7, 2000, XP, 2003, Microsoft IE 6.0 or above
Hardware

6/42
Suggested Intel Dual Core 1.66G,RAM: 1024MB, Graphic card: 128MB
Minimum Intel-C 2.8G, RAM: 512MB, Graphic card: 64MB
*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
III. Product Installation
A. Monitor Setting
i. Right-Click on the desktop. Select “ Properties”
ii. Change color quality to highest (32bit).

7/42
B. Hardware Installation and I/O Pin
Assignment
i. Connect a power adapter and IP Camera to PC or local network
ii. I/O Control Instruction
I/O terminal connector – used in application, for e.g., motion detection, event
triggering, alarm notifications. It provides the interface to:
1 Digital Input (GND+Alarm) – An alarm input for connecting devices that can
toggle between an open and closed circuit, for example: PIRs, door/window
contacts, glass break detectors, etc. When a signal is received the state changes
and the input becomes active.
Relay output (COM +N.O.) / (COM+N.C.) – An output to Relay switch, for
example: LEDs, Sirens, etc
iii. Digital Input
Alarm Input
1. GND (Ground) : Initial state is LOW
2. Alarm : Max. 50mA, DC 3.3V
3.5mm Phone Jack
(
Audio In
p
ut
,
Red
)
3.5mm Phone Jack
(
Audio Ou
t
p
ut
,
Green
)

8/42
Relay Output
1. N.C. (Normally Close): Max. 1A, 24VDC or 0.5A, 125VAC
2. COM: (Common)
3. N.O. (Normally Open): Max. 1A, 24VDC or 0.5A, 125VAC
iv. Relay
1. Digital Input connection
GND
ALARM
N.C.
COM
N.O.
Door/Window
Contacts
ALARM IN
RELAY OUT

9/42
2. Relay Output Connection
Or
GND
ALARM
N.C.
COM
N.O.
GND
ALARM
N.C.
COM
N.O.

10/42
v. PoE ( Power Over Ethernet)(Optional) 802.3af, 15.4W PoE Switch is
recommended
Power over Ethernet (PoE) is a technology that integrates power into a
standard LAN infrastructure. It enables power to be provided to the
network device, such as an IP phone or a network camera, using the
same cable as that used for network connection. It eliminates the need
for power outlets at the camera locations and enables easier application
of uninterruptible power supplies (UPS) to ensure 24 hours a day, 7 days
a week operation.
Ethernet
PoE Switch
PoE IP Camera
PoE IP Camera
Ethernet Cable
Ethernet Cable

11/42
C. IP Assignment
i. Use the software, “IP Installer” to assign the IP address of IP CAMERA.
The software is in the attached software CD.
ii. IP installer supports two languages
a. IPInstallerCht.exe：Chinese version
b. IPInstallerEng.exe：English version
iii. There are 3 kinds of IP configuration.
a. Fixed IP (Public IP or Virtual IP)
b. DHCP (Dynamic IP)
c. Dial-up (PPPoE)
iv. Execute IP Installer
v. For Windows XP SP2 user, it may popup the following message box.
Please click “Unblock”.
vi. IP Installer configuration:
vii. IP Installer will search all IP Cameras connected on Lan. The user can
click “Search Device” to search again.

12/42
viii. Click one of the IP Camera listed on the left side. The network
configuration of this IP camera will show on the right side. You may
change the “name” of the IP Camera to your preference (eg: Office,
warehouse). Change the parameter and click “Submit” then click “OK”. It
will apply the change and reboot the Device.
ix. Please make sure the subnet of PC IP address and IP CAM IP address
are the same.
The same Subnet:
IP CAM IP address: 192.168.1.200
PC IP address: 192.168.1.100
Different Subnets:
IP CAM IP address: 192.168.2.200
PC IP address: 192.168.1.100
To Change PC IP address:
Control PanelÆNetwork ConnectionsÆLocal Area Connection
PropertiesÆInternet Protocol (TCP/IP) ÆProperties
Please make sure your IP Camera and PC have the same Subnet. If not,
please change IP Camera subnet or PC IP subnet accordingly.
x. A quick way to access remote monitoring is to left-click the mouse twice
on a selected IP Camera listed on “Device list” of IP Installer. An IE
browser will be opened.

13/42
xi. Then, please key in the default “user name: admin” and “password:
admin”.
D. Install ActiveX control:
For the first time to view the camera video via IE, it will ask you to install the
ActiveX component.
If the installation failed, please check the security setting for the IE browser.
i. IE ÆTools ÆInternet Options… ÆSecurity Tab ÆCustom Level… Æ
Security Settings ÆDownload unsigned ActiveX controlsÆSelect
“Enable” or Prompt.
ii. IE ÆTools ÆInternet Options… ÆSecurity Tab ÆCustom Level…
ÆInitialize and script ActiveX controls not marked as safe ÆSelect
“Enable” or Prompt.

14/42
1 2
3 4
5
When popup the following dialogue box, click “Yes”.

15/42
IV. Live Video
Start a IE browser, type the IP address of the IP camera in the address field. It will
show the following dialogue box. Key-in the user name and password. The default
user name and password are “admin” and “admin”.
When connect to the IP CAMERA。The following program interface shows.
1 2
3
4 5 6 7

16/42
1. ：Get into the administration page
2. ：Video Snapshot
3. Show system time, video resolution, and video refreshing rate
4. Select video streaming source (When streaming 2 setting in『Video Setting』is closed, this
function will not display)
5. IP Camera supports 2-way audio. Click the “Chatting” check box. Then you can
use microphone which connects to the PC to talk to server side, which is IP
Camera side
6. Shows how many people connect to this IP camera
7. Control the relay which is connected to this camera.
Double-click the video, it will change to full screen mode. Press “Esc” or double-click
the video again, it will change back to normal mode.
Right-Click the mouse on the video, it will show a pop-up menu.
1. Snapshot：Save a JPEG picture
2. Record Start：Record the video in the local PC. It will ask you where to save the
video. To stop recording, right-click the mouse again. Select “Record Stop”. The
video format is AVI. Use Microsoft Media Player to play the recorded file.
3. Mute：Turn of the audio. Click again to turn on it.
4. Full Screen：Full-screen mode.

17/42
V. Configuration
Click to get into the administration page. Click to go back to the live
video page.

18/42
A.System
i、System Information
a. Server Information: Set up the camera name, select language, and
set up the camera time.
1. Server Name：This is the Camera name. This name will show
on the IP Installer.
2. Select language：There are English, Traditional Chinese, and
Simplified Chinese to select. When change, it will show the
following dialogue box for the confirmation of changing
language.
b. OSD Setting: Select a position where date & time stamp / text
showing on screen.
Moreover, click Text Edit can entry to adjust the OSD contents
which is including Size and Alpha of text. Finally, click Upgrade
button to reserve the setting.
c. Server time setting：Select options to set up time - “NTP”,
“Synchronize with PC’s time”, “Manual”, “The date and time remain
the same”.

19/42
ii、User Management
IP CAMERA supports three different users, administrator, general user,
and anonymous user.
a. Anonymous User Login：
Yes：Allow anonymous login
No：Need user name & password to access this IP camera
b. Add user：
Type the user name and password, then click “Add/Set”.
c. Click “edit” or “delete” to modify the user.

20/42