IP Camera HLV-1WCF User manual

1/75
User Manual
IP VANDAL DOME
CAMERA

2/75
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MISTURE.
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION：TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
COPYRIGHT
THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED
TO THEIR RESPECTIVE COMPANIES.

3/75
Content
I. PREFACE ............................................................................................................4
II. PRODUCT SPECIFICATIONS.............................................................................4
III. PRODUCT INSTALLATION.................................................................................7
A. MONITOR SETTING..............................................................................................7
B. HARDWARE INSTALLATION....................................................................................8
C. IPASSIGNMENT ................................................................................................14
D. INSTALL ACTIVEXCONTROL:...............................................................................18
IV. LIVE VIDEO.......................................................................................................24
V. IP CAMERA CONFIGURATION ........................................................................28
A. SYSTEM ...........................................................................................................29
B. NETWORK ........................................................................................................34
C.A/V SETTING .......................................................................................................46
D. EVENT LIST......................................................................................................54
VI. NETWORK CONFIGURATION..........................................................................64
VIII. FACTORY DEFAULT.........................................................................................70
IX. UNIVERSAL PASSWORD ..................................................................................71
X. PACKAGE CONTENTS........................................................................................74
XI. MICRO SD CARD COMPATIBILITY..................................................................75
V1.1_20131030

4/75
I. Preface
This is a 5 megapixel IP vandal dome Camera with a web server built in. The user
can view real-time video via IE browser. The IP Camera supports simultaneously
H.264, Motion JPEG & MPEG4 video compression and dual streaming, which
provides smooth and high video quality. The video can be stored in a micro SD
card and playback remotely. With a user friendly interface, it is an easy-to-use IP
Camera designed for security applications.
II.Product Specifications
5 Megapixel Vandal Dome
Support Full HD 1080P Real Time
External Vari-focal Lens Adjustment
3D+2D Digital Noise Reduction
Support Digital Wide Dynamic Range
Power over Ethernet Available
IR LED Built in 15M Available
Mechanism IR Cut Filter Available
H.264/ M-JPEG/ MPEG4 Compression
Micro SD Card Backup(Option)
Support 2-wayAudio
Video Output
Support iPhone/iPad/Android
SDK for Software Integration

5/75
Specifications
Hardware
CPU
ARM 9 ,32 bit RISC
RAM
256MB
Flash
16MB
Image sensor
1/3.2” Megapixel CMOS sensor
Lens Type
Vari-focal Lens 3[email protected]
Sensitivity
B / W: 0.1 Lux (AGC ON)
Angle of View
27.31°~ 75.22°(H)
19.09°~ 54.16°(V)
ICR
Mechanism IR cut Filter (optional)
LED
Built-in 18 IR LED
IR Distance 15M
I/O
1 DI / 1 DO
Video Output
Yes
Audio
G.711(64K) and G.726(32K,24K) audio
compression
Input : External Audio in
Output: External Line out
Power over Ethernet
Yes, PoE Class 0 (IEEE802.3af)
Power
DC 12V Max: 4.8W(IR ON), 6.1W(IR OFF)
PoE Max: 802.3af, 5.8W(IR ON), 7.2W(IR OFF)
Operating Temperature
-10°C ~ 45°C
Dimensions
φ137mm x 102mm (H)
Weight
890 g
Network
Ethernet
10/ 100 Base-T
Network Protocol
IPv6, IPv4, HTTP, HTTPS, SNMP, QoS/DSCP,
Access list, IEEE 802.1X, RTSP, TCP/ IP, UDP,
SMTP, FTP, PPPoE, DHCP, DDNS, NTP, UPnP,
3GPP, SAMBA, Bonjour
System
Video Resolution
2592x1944@15fps, 2048x1536@15fps,
1920x1080@30fps, 1280x720@30fps,
640x480@30fps, 320x240@30fps,
176x144@30fps

6/75
Video Adjust
Brightness, Contrast, Hue, Saturation,
Sharpness, Shutter Speed adjustable, AGC,
Sense-Up, D-WDR, Flip, Mirror, Noise reduction,
Day&Night adjustable, White Balance
Triple Streaming
Yes
Image snapshot
Yes
Full screen monitoring
Yes
Privacy Mask
Yes, 3 different areas
Compression format
H.264/ M-JPEG/ MPEG4(3GPP Only)
Video bitrates adjust
CBR, VBR
Motion Detection
Yes, 3 different areas
Triggered action
Mail, FTP, Save to SD card, DO, SAMBA
Pre/ Post alarm
Yes, configurable
Security
Password protection, IP address filtering, HTTPS
encrypted data transmission, 802.1X port-based
authentication for network protection
Firmware upgrade
HTTP mode, can be upgraded remotely
Simultaneous connection
Up to 10
SD card management
Recording trigger
Motion Detection, IP check, Network break down
(wire only), Schedule, DI
Video format
AVI, JPEG
Video playback
Yes
Delete files
Yes
Client System requirement
OS
Windows 7, 2000, XP, 2003, Microsoft IE 6.0 or
above, Chrome, Safari, Firefox
Mobile Support
iOS 4.3 or above,Android 1.6 or above.
Hardware Suggested
Intel Dual Core 2.8G,RAM: 4GB
*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTIFICATION.

7/75
III. Product Installation
A. Monitor Setting
i. Right-Click on the desktop. Select “ Properties”
ii. Change color quality to highest (32bit).

8/75
B. Hardware Installation
1. Connector Instruction
Open the cover to find the cable connector inside the Camera.
Connect power adaptor first, then connect the IP Camera to PC or
network, and set up the network configurations according to the network
environment.

9/75
2. Vandal Dome Installation Tips
In order to ensure IP66 waterproof level, please install the vandal
dome according with following instructions.
a. The Unused cable outlet hole must be closed, and the
waterproof connector on the used hole must be locked
closely.

10/75
For keeping the IP, when using separate cables for Power and Internet, please use
silicon in the cable gland, around the cables, just as shown in the following picture,
indicated in yellow color.
b. It is recommended that the bottom of housing be set smooth and
closely flat with the surface.
c. When you mount the camera housing on the ceiling or wall, please use
the screws with the black rubber o-rings. Without the o-ring, the water
may seep into the machine.
Make sure there are no cables around the screws, and slowly lock the
four corners at the same time, applying equal force in every corner. Do
not totally lock one screw at a time; otherwise the closing might not be
equal in all four screws.

11/75
After locking the four screws the space between top-bottom sides will
disappear.
d. Turn and loose the control stick, shift right and left to adjust the
vari-focal lens until the image becomes clear, then turn and tighten
the stick to fix it.
e. Use the 3-Axis bracket to adjust the camera to appropriate angle.

12/75
f. Before you close the dome cover, make sure that the black rubber
band sticks to the inside of the cover completely. Crook or uneven
rubber band may cause the waterproof defective.
g. Lock tightly the screws on the dome cover to ensure there's no
gap between the lid and base.

13/75
3. PoE (Power Over Ethernet)(Optional) 802.3af, 15.4W PoE Switch is
recommended
Power over Ethernet (PoE) is a technology that integrates power into a
standard LAN infrastructure. It enables power to be provided to a
network device, such as an IP phone or a network camera, using the
same cable as that used for network connection. It eliminates the need
for power outlets at the camera locations and enables easier application
of uninterruptible power supplies (UPS) to ensure 24 hours a day, 7 days
a week operation.

14/75
C. IP Assignment
i. Use the software, “IP Installer” to assign the IP address of IP CAMERA.
The software is in the attached software CD.
ii. IP installer supports two languages
a. IPInstallerCht.exe：Chinese version
b. IPInstallerEng.exe：English version
iii. There are 3 kinds of IP configuration.
a. Fixed IP (Public IP or Virtual IP)
b. DHCP (Dynamic IP)
c. Dial-up (PPPoE)
iv. Execute IP Installer
v. For Windows XP SP2 user, it may popup the following message box.
Please click “Unblock”.

15/75
vi. IP Installer configuration:
vii. IP Installer will search all IP Cameras connected on LAN. The user can
click “Search Device” to search again.
viii. Click one of the IP Camera listed on the left side. The network
configuration of this IP camera will show on the right side. You may
change the “name” of the IP Camera to your preference (e.g.: Office,
warehouse). Change the parameter and click “Submit” then click “OK”. It
will apply the change and reboot the Device.

16/75
ix. Please make sure the subnet of PC IP address and IP CAM IP address
are the same.
The same Subnet:
IP CAM IP address: 192.168.1.200
PC IP address: 192.168.1.100
Different Subnets:
IP CAM IP address: 192.168.2.200
PC IP address: 192.168.1.100
To Change the PC IP address:
Control PanelNetwork ConnectionsLocal Area Connection
PropertiesInternet Protocol (TCP/IP) Properties
Make sure your IP Camera and PC have the same Subnet. If not, change the
IP Camera subnet or PC IP subnet accordingly.

17/75
x. A quick way to access remote monitoring is to left-click the mouse twice
on a selected IP Camera listed on “Device list” of the IP Installer. An IE
browser will be opened.
xi. Then, please key-in the default “user name: admin” and “password:
admin”.

18/75
D. Install ActiveX control:
1. To users of IE 6.0 above:
In the first time you access the camera via IE, it will ask you to install the
ActiveX component. If the installation failed, please check the security setting
for the IE browser.
1. If the installation failed, please check the security setting for the IE browser.
i. IE Tools Internet Options… Security Tab Custom Level… 
Security Settings Download unsigned ActiveX controlsSelect
“Enable” or Prompt.
ii. IE Tools Internet Options… Security Tab Custom Level…
Initialize and script ActiveX controls not marked as safe Select
“Enable” or Prompt.

19/75
1
2
3
4

20/75
5
When pops up the following dialogue box, click “Yes”.
2. You can choose another way:
Go to: IE→Tools → Internet Options… → Security Tab → Trusted sites → Add the
IP address and click "OK".
In the site list you can key one single IP address or a LAN address. For example,
if you add "192.168.21.*", all the IP address under .21 LAN will be regarded as
trusted sites.