iPixel LED Light XB-808-A User manual

1
XB-808-A master control
一、Master control system features
Salient features:
1. Strong performance, can carry up to 160,000 pixels or 60 sub-controls.
2. Integrate BTS synchronization function, 4G network communication function and offline playback function into one,
which is convenient and reliable to use.
3. Support Bluetooth, RF, remote 4G network communication, can be controlled by PC / mobile APP.
4. Can realize any timing, multi-level encryption function.
5. Have a unique identity code UID.
Conventional features:
1. The playback content is stored in the SD card. The SD card can store up to 32 effect files, it’s capacity supports
4G-32GB. It supports single-effect playback, effect loop playback, and the effect is accelerated and decelerated.
2. The master control can be used for the automatic/manual numbering of the sub-control ID. It can be numbered
together with multiple controllers, or it can be numbered separately.
3, The master control comes with built-in effects, can test the loaded lamps (RGB / RGBW lamps are supported).
4, The controller has DMX512 write address function and address test, single port or all ports support DMX512 IC
write address, and make address test of the lamp.
5, the controller uses the standard TCP / IP network protocol, signal transmission is more stable; optional 100 Mbps /
Gigabit transmission rate.
6, If use together with our T-700K/T-800K for offline use, supports up to 160,000 pixels or 60 controllers.
7, Support timing (holiday) playback.
8. Support BTS base station timing synchronization, GPS satellite timing synchronization.
9, Support a variety of encryption methods.
10. The IC controller for DMX lamps has its own address writing function. In addition, with the latest LedEdit-K
software of our company, one-click address setting function can be set. Press and hold (SET) to write the address with one
click.
二、Support controllers：

2
T-700K/ T-800K
三. Controller pictures
Controller indentification
1.485 control interface
2. Power indicator
3. Status indicator
4.BTS antenna
5.SD card slot
6.BTS signal indicator
7.NET1 signa llight
8.NET1 network port
9.NET2 network port
10.NET2 signal light
11.LCD display screen
12.SET button
13.MODE button
14.SPEED+ button
15.SPEED- button
16.SIM antenna
17.SIM card slot
18.Switch
19. Power interface
四、Indicator and button definition
1.Indicator definition：
POWER
Power indicator
After power on always on
STATUS
Status indicator
Normally extinguished
BTS
BTS signal light
Strobe with BTS signal
NET1
Cascade signal input
Strobe with signal input
NET2
Cascade signal output
Strobe with signal output
2. Port definition
Power supply
AC110-240V input
NET1
Network signal interface
A1/B1
1st channel 485 interface
NET2
Network signal interface
A2/B2
2nd channel 485 interface
BTS
BTS antenna interface
SD
SD card slot
SIM
SIM antenna interface
SIM
SIM card slot
3. Speed level corresponding frame:
Speed level
Frame/second
Speed level
Frame/second
Speed level
Frame/second
Speed level
Frame/second
1
4 frame
5
8 frame
9
14 frame
13
23 frame
2
5 frame
6
9 frame
10
16 frame
14
25 frame
3
6 frame
7
10 frame
11
18 frame
15
27 frame

3
4
7 frame
8
12 frame
12
20 frame
16
30 frame
4. Button function
SET
MODE
SPEED+
SPEED-
Playback mode
/
/
/
/
Numbering mode
Number start button
/
Digital plus
Digital subtraction
Parameter setting
mode
Parameter setting / entry
Project selection
Parameter adjustment +
Parameter adjustment -
Built-in effect playback
Chip selection
Mode selection
Speed +
Spped -
Remarks
Normally boot into normal mode,
the button has no effect
Press “SET”to power on, enter parameter
setting mode/function setting
Press "-" to power on, enter
the numbering mode
5. Display definition:
Display
Definition
Playback mode
MODE: Effect mode TIM timing play
Speed：play speed I_BTS BTSSignal synchronization timing
Numbering mode
Sub-control number Start ID：001
Built-in effect playmode
CHIP: chip 3：light channel
MOD: Built-in effects SPD: play speed
DMX512IC Address writing mode
Refer to DMX512IC address writing mode and test
Light address test mode
Refer to the light address test mode
五、Wiring diagram
1、Single set master control

4
2、Online offline integration control
3、Synchronous control of multiple master BTS base stations
4、Multiple master control integration control

5
六、Function intruduction
Master long press “SPEED-” button to power on.
Display interface 1:
○
1Set Slave ID Control number
○
2Set BTS BTS switch
○
3Set TIME Time setting
○
4Set IP IP/ID seting
○
5Read UID UID Number reading
○
6Set 100-BASE Transmission rate setting
○
7ModBus Address Master number (third-party device control)
Mater long press“Set” button to power on. display
interface 2：
○
8PLAY Built-in effect playback
○
9WRITIE ADDRESS: DMX address writing and test
○
10 TEST DMX ADDR DMX address test
○
11 TEST LINE Line test
○
12 RGB,RGBW Lamp channel selection
1、Sub-control number function
The main control and the sub-control are connected through the network cable (using the

6
international standard TCP/IP network protocol, and the network cable is 568B through).
1.1. The master control presses the “SPEED-” button to turn it on, and the “MODE” button adjusts
the arrow to select “Set Slave ID”.
As shown in the figure:
1.2. Press “SET” to enter the sub-control number page. The “Speed+” button and the “Speed-”
button adjust the number of the starting sub-control, as shown below:
1.3. After completing the number setting, press the “SET/Save”button to start the numbering;
1.4. The first step of the controller number is to automatically count the number of sub-controls. The
display “Write OK: 003”(take the 3 sub-control numbers as an example);
1.5. The number is completed, the main control display: As shown in the figure "Write Num: 003", 3
controllers are programmed;
"Last ID: 003" The last controller is numbered 3;
Sub-control display:
The first set: A-01 The second set: A-02 The third set: A-03
1.6. Check the sub-control number. If need to re-number, press and hold the “SPEED-” button to
restart the number. If you do not need to re-number, press any button—the main control
restarts and returns to the play mode.
Note 1: When the controller is numbered, the level networking ports must be connected in strict
accordance with the controller silkscreen prompt (IN/OUT).
2、BTS switch function

7
2.1. The master control long press the “SPEED-”button to turn it on, and the “MODE”button
will adjust the arrow to select “Set BTS”.
As shown in the figure:
2.2. Press the “SET” button again to enter the BTS setting page. The “SPEED+” button and the
“SPEED-” button move the arrow up and down to select the setting, as shown below:
① BTS Turn ON BTS turn on
② BTS Turn OFF BTS turn off
2.3. Press “MODE” button to confirm selection, display as below:
OR
2.4. Confirm that the settings are correct, press “SET” to exit the interface; restart the controller and
return to playback mode.
3、Time settting
3.1. The master control long press “SPEED-” button to power on; “MODE”button adjusts the arrow
to select “Set TIME”.
As shown in the figure:
3.2. Press “SET” again to enter the time setting page; “MODE” button to adjust the cursor position;
“Speed+” button
And the "SPEED-" button to select settings, as shown below:
Year/month/date/hour/minute/second/week
3.3. The time setting is completed and the save settings are restarted.
4、IP/ID setting (4G cloud)
4.1. The master control long presses the “SPEED-” button to power on, and the “MODE” button
adjusts the arrow to select “Set IP”;
As shown in the figure:
4.2. Press the “SET”button to enter the IP settings page;
① Global ID Global ID
② Local ID Local ID
③ User IP IP address
④ Return Return to the main interface

8
Note: Multiple masters are used at the same time, and the global ID cannot be repeated.
4.3. The “MODE”button adjusts the arrow up and down to select “Global ID”or “Local ID”;
the “SPEED+”button and the “SPEED-”button for ID setting.
4.4. “MODE” button adjusts the arrow position to “User IP”; Press “SPEED+” to enter IP address
setting.
As shown below: (The IP is the factory test IP)
Note: IP address setting, generally change the factory setting IP to the IP address used by the real project.
4.5. The “MODE” button adjusts the cursor position; the “SPEED+” button and the “SPEED-”
button perform IP settings.
4.6. Complete the IP address setting, press “SET”to exit and return to the previous interface.
4.7. Press the “SET”button again to save the previous IP address and ID settings, then the
controller will display:
4.8. After completing the IP/ID setting, the controller display automatically returns to the IP setting
interface; the “MODE” button adjusts the arrow to select “Return”.
Press the “SET” button again to exit and return to the main interface.
4.9. Restart the controller and return to playback mode.
5. UID reading
Each master has a unique UID identity number for use as a wireless connection (RF/Bluetooth)
device identification.
5.1. The main control presses the “SPEED-” button to turn it on, and the “MODE” button adjusts
the arrow to select “Read UID”.
As shown in the figure:
5.2. Press the “SET” button again to enter the UID read page, for example: UID: 001199
5.3. Press “SET” to exit, return to the main interface and restart the controller to return to
playback mode.

9
6、Transmission rate selection
6.1. The master presses the “SPEED-” button to turn it on, and the “MODE” button adjusts the
arrow to select “Set 100-Base”.
As shown in the figure:
6.2. Press the “SET”button again to enter the
transmission rate selection page:
① 100-BASE 100M rate
② 1000-BASE Gigabit rate
6.3. The “SPEED+” button and the “SPEED-” button adjust the arrow to move up and down; press the
“MODE” button to confirm the selection, as shown below:
OR
6.4. Confirm the selection is correct, press the “SET” button to exit, return to the main interface,
restart the controller and return to the playback mode.
7、Master control number（Third party device control）
When using a third-party device to control the master operation, multiple master number
operations are required.
7.1. The master control presses the “SPEED-” button to turn it on, and the “MODE” button adjusts
the arrow to select “ModBus Address”.
As shown in the figure:
7.2. Press the “SET”button again to enter the main control number page:
7.3. Press the “SPEED+” button and the “SPEED-” button to adjust the number; press the
“MODE” button to confirm the selection, as shown below:
7.4. Confirm the selection is correct, press the “SET”button to exit, return to the main
interface, restart the controller and return to the playback mode.
8、Built-in effect playback (Luminaires that support RGB/RGBW channels)
8.1. Press the “SET”button and the controller is turned on. Press the “MODE”button to move

10
the arrow to select “PLAY”.
As shown in the figure:
8.2. Press the “SET”button again to enter the built-in effect playback interface, as shown in the
figure:
①. CHIP chip mode code（Refer to IC mode list）
②. 3Channel selection（3/4）
③. MOD Built-in effects code（Refer to built-in
effects list）
④. SPD Playback speed level（Refer to the speed level corresponding frame list）
Note: When the built-in effect is played, the supported lamp channel is set by the “Lamp
Channel Selection Mode”.
8.3. Button function list
Button silk
screen
SET button
MODE
SPEED+
SPEED-
Function
Chip selection
Mode selection
Speed +
Speed -
8.4. Press “SET” to switch IC model
IC model list
1
DMX (Standard 250Kbps)
5
TM1803
2
UCS1903
6
GS8205
3
SM16703
7
DMX 500K
4
WS2811
8.5.Press “MODE” to switch built-in effects
Built-in effects list
1
Colorful jump
3
Colorful change
2
Colorful gradient
4
White light gradient
8.6. Press "SPEED+" and "SPEED-" to switch the speed:
Speed level corresponding frame list
Speed
Frame/se
cond
Speed
Frame/se
cond
Speed
Frame/se
cond
Speed
Frame/se
cond
1
4 frame
5
8 frame
9
14 frame
13
23 frame
2
5 frame
6
9 frame
10
16 frame
14
25 frame
3
6 frame
7
10 frame
11
18 frame
15
27 frame
4
7 frame
8
12 frame
12
20 frame
16
30 frame
8.7. After the built-in effect playback is completed, shut down and restart, and return to the playback
mode.
9、DMX512 IC Address writing mode and test（Can address a single port of a single controller）
9.1. Press the “SET” button and the controller is turned on. Press the “MODE” button to move the

11
arrow to select “WRITE ADDRESS”.
As shown in the figure:
9.2. Press “SET”to enter the address mode interface, as shown in the figure:
①. START CH: Starting channel
（The starting address is set in the range of
0-512, and the regular is 001.）
②. CH MODE: Interval channel
（Interval channel setting in the range of 0-255）
③. IC : Chip model
（Refer to DMX512 IC list ）
④. CONTR NUM Controller number
(ALL controllers/ Single controller number
01-60)
⑤. PORT NUM: Address writing port Refer to the port code list
（ALL ports/single port 1-8）
⑥. RETURN return to main interface
9.3. Press the “MODE”button to move the arrows, and press “SPEED+”and “SPEED-”to set
the start channel/interval channel/IC option/select the address controller/select the address
port.
1.DMX512 IC list
UCS512A*/B*,TM512AL1/AB
WS2821
DMX512AP
UCS512C*，
TM512AC*
SM1651*-3
SM1651*-4
UCS512D*/TM512AD
*
UCS512-E
SM17512*
SM17522*
UCS512-F
TM512AC*
GS8512
SM17500
2. Controller port code list
1
Port OUT1
5
Port OUT5
2
Port OUT2
6
Port OUT6
3
Port OUT3
7
Port OUT7
4
Port OUT4
8
Port OUT8
ALL
All ports OUT1-8
Note: All port addresses of the controller are also supported, and single port
address is also supported.
9.4. Select to complete each item, press “SET” to start writing; at this time, the screen displays
“Writing Add...”, the port indicator flashes, and then “Writing OK!” appears to indicate that the
address is completed.

12
9.5. After the address is written, the controller automatically jumps to the address test function. At
this time, the screen displays:
①. AC: **** Automtic test
②. MC: **** Manual test
③. ALL- ALL All controller all ports
④. CH MODE：Channel (Interval channel is not adjustable）
Note: The address port is set by "CONTR NUM /PORT NUM" before address writing (in this case, all ports of all
controllers)
9.6. Press the “MODE” button to enter the “AC” automatic test mode, the lamps will start to light up in sequence,
and the number will increase automatically;
The controller displays the following picture:
9.7. Press the “MODE” button again to enter the “MC”
manual test mode; “SPEED+” and “SPEED-” can adjust
the pixel points (long press “SPEED+” and “SPEED-” can
quickly increase or decrease), and the lamps will light
up one by one;
Display as shown:
9.8. After the test is completed, press “SET”to exit the channel test and return to the write address
interface.
9.9. Press the “MODE”button to move the arrow to select “Return”, then press “SET”to exit
the address and test, and then restart to return to the playback mode.
10、Lamp address test mode（Test the load on all ports of the controller）
10.1. Press the “SET”button and turn on the controller. Press the “MODE”button to move
the arrow to select “TEST DMX ADDR”.
As shown in the figure:
10.2. Press the “SET”button again to enter the luminaire test mode interface, as shown in the
figure.
①. AC: **** Automatic test
②. MC: **** Manual test
③. ALL-ALL：All controllers all ports
④. CH MODE：Channel

13
10.3. Press the “MODE”button to start the test, as shown in the figure:
10.4. Press the “MODE” button to switch the test channel option.
Press the “SET” button to switch between the manual channel test mode and the automatic
channel test mode;
Press the “SPEED+” and “SPEED-” keys to adjust the lamp number in the manual channel
test mode;
Lamp test vocabulary definition
Automatic mode:AC
Definition
Manual mode:MC
Definition
AC：**** ALL-ALL
CH MODE: RGBW
1 channel automatic test
MC：**** ALL-ALL
CH MODE: RGBW
1 channel manual test
AC：**** ALL-ALL
CH MODE: RG,BW
2 channel automatic test
MC：**** ALL-ALL
CH MODE: RG,BW
2 channel manual test
AC：**** ALL-ALL
CH MODE: R,G,B
3 channel automatic test
MC：**** ALL-ALL
CH MODE: R,G,B
3 channel manual test
AC：**** ALL-ALL
CH MODE: R,G,B,W
4 channel automatic test
MC： **** ALL-ALL
CH MODE:
R,G,B,W
4 channel manual test
Note 1: Automatic and manual test mode switching: AC is the automatic test mode, MC is the manual test mode,
and is switched by the “SET” key;
Note 2: luminaire channel switching, RGBW is a monochrome single-channel luminaire; RG, BW is a two-color
two-channel luminaire; R, G, B are three-color luminaire; R, G, B, W are RGBW four-color luminaire, by
"MODE ”Key switch;
Note 3: **** is the lamp number; in the automatic test mode, after the number is automatically incremented to
the maximum value, the test starts again from 0001; in the manual test mode, the number is manually
adjusted by “SPEED+” and “SPEED-”.
10.5. After the test is completed, the power is turned off and the controller can enter the play mode.
11、Line test TEST LINE
11.1. Press the “SET”button and turn on the controller. Press the “MODE”button to move the
arrow to select “TEST LINE”.
As shown in the figure:
11.2. Press the “SET”button again to enter the line test
interface, as shown in the figure:
①. START ID Starting controller number

14
②. END ID End controller number
③. RETURN Return
Note: Enter the interface default test (No. 1-20 controller)
11.3. Press the “MODE”button to move the arrow to the selection, and press the “SPEED+”
and “SPEED-”buttons to adjust the start controller/end controller number.
11.4. Press the “SET”button to start the test, as shown in
the figure:
11.5. Wait for a while, controller display test results
Press the “MODE” button to move the arrow up and
down to view the data packet loss rate of each
controller.
Loke “LOS :0000” shows the connection is normal,
If the packet loss rate is greater than 0, the line
connection is abnormal；
The packet loss rate is 1700, that is, all data is lost.。
As shown in the figure "019 LOS: 1700" on the right, it is
necessary to check the line connection when the 19th
station is completely disconnected until the test packet loss rate is "0000".
11.6. Press the “SET”button to exit the test result interface.
11.7. Press the “MODE”button to move the arrow to select “Return”, press “SET”to exit
the line test, and shut down to restart the playback mode.
12、Lamp channel selection (Built-in effect playback supports RGB/RGBW IC channel selection)
12.1. Press the “SET”button and the controller is
turned on. Press the “MODE”button to move the
arrow to select “RGB, RGBW”.
As shown in the figure:
12.2. Press the “SET”button again to enter the lamp channel selection interface, as shown in the
figure:
①. RGB Three-channel luminaire
②. RGBW Four-channel luminaire
12.3. Press the “SPEED+”and “SPEED-”buttons to move the arrow up and down to select the
RGB/RGBW channel option.

15
12.4. Press the “MODE”button to confirm the selection, as shown in the two settings:
OR
12.5. Select to complete the lamp channel selection, press “SET” to exit and return to the main
interface.
七、DMX512 One-click address writing
1. One-click address writing：(as picture 1）
When the software writes the program output, click the button to enter the one-click address writing
interface.
2. Interval channel input（As picture 2）
The interval channel is input according to the actual digital input of the luminaire. The number is
the number of channels occupied by a DMX512 IC to control the pixel points of the luminaire.
3.Chip model selection（as picture：2）
Click the drop-down button to select the chip model corresponding to the DMX512 IC on the
luminaire.
4. Complete the one-click address writing setting.
Confirm that the settings are correct and click the OK button to complete the program output.
5. Controller one-click write code operation
① Insert the SD card into the controller;
② Power on the controller；
③Press and hold the “SET”button for 10 seconds, the controller will display Writing Addr...,
until the address is completed, it will display Writing OK;

16
④After the address is written, the controller will also enter the channel test mode (same as the
channel test after manual address).
⑤After completing the channel test, press the “CHIP”button to exit the test mode, and the
controller returns to the play mode to work normally.
八、Bluetooth control
The controller has a built-in Bluetooth receiver module that can be controlled using the mobile
APP.
1. Mobile phone installation Bluetooth debugging APP；
2. The phone turns on the Bluetooth function, click on the APP, search for the controller, as shown in
Figure 1；
3. Select and click the Bluetooth number of the controller to enter the control page, as shown in
Figure 2；
图1图2图3
①Program selection area：Select the effect program in the SD card; click on the program in the drop-down
menu；
②Color debug area：Instantly adjust the luminaire to display the clicked color;
③Speed adjustment area：16-speed level adjustment；
④Play operation area：Play/pause, cancel (control), loop (play), save (set) four selection options;
⑤Other operation area: Device management, built-in effects, channel brightness, dimming settings, DMX write
code, test DMX address, restart master, as shown in Figure 3；

17
4. Equipment management (Figure 4)
Add node: The phone controls multiple controllers simultaneously by adding nodes (controllers)
①UID：Fill in the new node (controller) UID number - obtained by manually reading the master UID
number;
②Name: Write the node name
5. Built-in effects （As figure 5）
Click “Built-in effect” to select relevant options through the phone settings, and the master will
control the built-in effects to play the program;
①Play / Pause：Built-in effects play/pause
②Speed：1-16
③Program number：Program 1- program 4 are effective
④IC model：DMX 250K /UCS1903 / DMX500K
⑤Channel: 3 / 4
6. Channel brightness（figure 6）
Channel brightness: The brightness of each channel of the luminaire can be adjusted, and the
brightness setting parameters will be written into the controller (the setting will
be fixed after the brightness is set)
Figure4 Figure 5 Figure 6
7. Dimming settings（Figure 7）
Dimming setting: dimming test on the luminaire (to adjust the special color settings)
①IC model：DMX/ UCS1903

18
② Channel number：3 / 4
③Brightness adjustment：Red/green/Blue（0-255）
8. DMX code writing (Figure 8）
①Address writing mode：according to channel / the number of lights;
②Start channel：Manually input（1-4096）；
③Channel spacing：Fill in the actual interval channel（0-255）；
④Chip model：UCS512-A/B、WS2821、DMX512AP-N... Select according to the actual lamp carried IC;
⑤Designated controller: Select the sub-control number to write the address for the controller;
⑥Designated port：Select the sub-control port to specify the port address of the controller;
9. Test DMX address（Figure 9）
Test the lamp address is correct (lights are bright white)
①Channel spacing: actual interval (0-255);
②Lamp number: Click “+” and “—” to test when testing manually; when auto test, the number is
automatically increased (1-1536);
③Designated controller: Select the sub-control number to test for the controller;
④Designated port：Select the sub-control port to specify the port test of the controller;
Figure 7 Figure 8 Figure 9
九、Specific parameters
Memory Card：

19
Type: SDHC card
Capacity：4GB-32GB
Format：FAT32
Storage files：*.BIN
Physical parameter:
Operation temperature: -30℃—85℃
Operation power: AC 110-240V
Consumption: 5W
Weight: 1.2Kg
Data transmission interface: network port
Size: L356mm * W178mm * H45mm
十、SD card formatting
1、 The SD card must be formatted before copying the file to the SD card (note that it is formatted before each copy).
2、Formatting process
①SD card settings - "File System", "FAT" format
②SD Card Settings - "Assign Unit Size", click the drop down button
to select "Default Configuration Size" or click the "Restore Device Defaults"
button.
③Start formatting.
As shown below:
3、The SD card cannot be hot swapped, that is, the power of the
controller must be disconnected each time the SD card is inserted or removed.
十一、Precautions：
1. Controller and controller, controller and master, controller and computer, between two nodes use
super five network cable or above. The maximum cascading is 100 meters, beyond which the
switch or fiber can be added for long distance transmission.

20
2. Network cable crimping method is 568B straight through