iPort CONNECT PRO User manual

User Guide
Gigabit 30W PoE Injector
CONNECT
PRO

Package Contents
Check the following contents of your package:
z PoE Injector x 1
z User Guide x 1
z Power Cord x 1
The label is attached to the bottom of the switch
If any part is lost and damaged, please contact your local agent immediately.
Introduction
PoE Injector
Provides fully complies with IEEE 802.3af/at standard, and can work with all IEEE
802.3af /at PoE compliant PDs (Powered Devices) or PoE Receiver Adapters or other equivalent
product, to expand your network to where there are no power line or outlet, where you
wish to fix device such as AP, IP Camera or IP Phone, etc.
Hardware Description
Front Panel
The front panel composed by PSE output ports with data link port, the relevant indicator, as
shown below:

LED indicator
LED Color Function
PoE Green
Off: No PoE supply.
Light: Indicates the machine has PoE supply
Rear Panel
The rear panel of AC inlet power socket .
- 1 -

Installation
This part describes how to install your machine and make connections to it. Please follow the
following instructions in avoid of incorrect installation causing device damage and security
threat.
zBefore cleaning the machine, unplug the power plug of the machine first. Do not clean the
machine with wet cloth or liquid;
zDo not place the machine near water or any damp area. Prevent water or moisture from
entering the machine chassis;
zDo not place the machine on an unstable case or desk. The machine might be damaged
severely in case of a fall;
zEnsure proper ventilation of the equipment room and keep the ventilation vents of the
machine free of obstruction;
zMake sure that the operating voltage is the same one labeled on the machine;
zDo not open the chassis while the switch is operating or when electrical hazards are present
to avoid electrical shocks.
Desktop Installation
Install the Switch on a desktop, Allow adequate space for ventilation between the device and
the objects around it. The bottom is shown in figure:
- 2 -

Wall-mounted installation
In the first two fixed screw on the wall as shown in the figure below
Aim at the two fixed hole switches, and the machine smoothly on the screw
Note: The appliance inlet is served as disconnect device, the socket-outlet shall be i
nstalled near the equipment and shall be easily accessible
- 3 -

(72106)
(72102)
PoE+
Adapter
PoE+
Injector
PoE+
Injector
IPORT USB-C to
proprietary cable
IPORT Surface Mount
70752, 70754
70755, 70756
70508, 70806
PoE+

Specifications
Model PoE Injector
Port
Data in port:1 x 10/100/1000Mbps RJ45 port
PoE out port : 1x10/100/1000Mbps RJ45 port
Standard
IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3af,
IEEE802.3at
Network Media(Cable)
10BASE-T: UTP category 3, 4, ϱĐĂďůĞ;чϭϬϬŵͿ
100BASE-dyhdWĐĂƚĞŐŽƌLJϱĐĂďůĞ;чϭϬϬŵͿ
1000BASE-T: UTP category 5e ĐĂďůĞ;чϭϬϬŵͿ
Dimensions (L*W*H) 142 *60 *32 mm
mains input
AC 100V-240V 50/60Hz
PoE power output DC 55V Power 30W
PSE Power on RJ-45 Mode A: 1/2 ( +), 3/6 ( -)
PoE Output 30W(Max)
Temperature
Operating Temperature: 0°C ~ 40 °C (32 °F ~104°F )
Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F )
Humidity
Operating Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing
- 5 -

(72106)
(72109)
(72102)
PoE+ Upgrade Adapter or
PoE+ Adapter
PoE+
Injector
PoE+
Injector
PoE+
IPORT CONNECT PRO
BaseStation
72352
72353

(72106)
PoE+
Injector
PoE+
Injector
PoE+
IPORT CONNECT PRO
WallStation
72350
72351
(72109)
(72102)
PoE+ Upgrade Adapter or
PoE+ Adapter