iPuray BRT-310 User manual

Product Description of BRT-310 Page 1of 7
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
Smart Ceiling Mount PIR Remote Control
Model #：BRT-310
Features:
BRT-310 is a ceiling mount remote control which utilizes passive infrared (PIR) sensor to detect
the heat (in the form of infrared energy) from people moving within a space. It can determine
when a space is unoccupied and turns off the large loads such as air-conditioners, etc.,
automatically by sending out IR control signals.
Capable of learning and memorizing infrared control codes of all kinds of appliances;
Adjustable delay-off time from 1 minutes to 30 minutes;
Good for all kinds of appliances that have infrared control, such as air-conditioners, TVs,
fans, audios, etc.
Easy installation onto ceiling with or without a holder;
ABS-V0 flame resistance material; and
High quality build.
Front View and Back View:
Fig. 1 and Fig. 2 show the front view and the back view of BRT-310 PIR remote control
respectively.
Fig. 1 Front View Fig. 2 Back View

Product Description of BRT-310 Page 2of 7
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
Specification Parameters:
Input Voltage
220～240V(50Hz/60Hz)
Operation
Environment
No-condensation 20-90% RH，
-20℃～40℃
Control Mode
IR
Control
Distance
7m
PIR Coverage
Range
5m in diameter when
mounted at a height of 2.4m
Mounting Hole
Diameter
68mm
Dimension
(max)
Oval faceplate: 105mm
Circular faceplate: 77mm
Weight
110g
Wiring Diagram:
BRT-310 PIR remote control requires both hot wire and neutral wire for installation:
Hot wire (ACL): Coming from the power line with 220V;
Neutral wire (ACN): Usually coming with the hot wire; and
Fig. 3 BRT-310 Wiring Diagram
Fig. 3 shows the wiring diagram. Wiring must be done according to the diagram and the labelled
ports of the control.
Installation Guide:
There are two ways to install BRT-310 PIR remote control to the ceiling. Fig. 4 and Fig. 5 show
the step-by-step installation instructions, respectively.
Cautions:
1. Avoid mounting the control close to air vents, as the vibration and air flow can reduce its
effectiveness;

Product Description of BRT-310 Page 3of 7
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
2. Avoid installing the control in an electrical circuit which has other frequent on/off switch or
appliance, as those on/off actions could cause false triggers.
1. Installation using a holder
As shown in Fig. 4, a holder is attached to the ceiling using screws first. Then, the PIR remote
control can be easily snapped into the holder.
The holder is specially designed for BRT-310 PIR remote control. Please talk to our sales
representative when placing orders.
Fig. 4 Installation with a Holder
2. Installation without a holder
As shown in Fig. 5, without a holder, an opening in the ceiling needs to be made first. There are
four steps:
Step one: Open a hole of 68mm in diameter in the ceiling;

Product Description of BRT-310 Page 4of 7
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
(Attach the electrical wires as shown in the Wiring Diagram Fig. 3).
Step two: Open the two flexible clamps on the side surface of the remote control;
Step three: Insert the remote control into the hole; and
Step four: The clamps will hold the remote control onto the ceiling tight and steady.
Fig. 5 Installation without a Holder
Operation Guide:
BRT-310 PIR remote control needs a warm-up time about two minutes before it can operate
properly. It has dip switches for adjusting the delay-off time, as shown in Fib. 6. For the first time
operation, BRT-310 PIR remote control also needs to learn and memorize the IR remote control
codes from regular remote control set. BRT-310 PIR remote control has a button for this task as
shown in Fig. 6 as well.

Product Description of BRT-310 Page 5of 7
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
Fig. 6 Dip Switches and Button for Code Learning
As shown in Fig. 7, please rotate the front cover counter-clockwise to remove it so that the dip
switches and the button for code learning are exposed.
Fig. 7 Removing the Front Cover
1. Adjust the delay off time
The 4 dip switches are used to set the delay off time to 8 settings based on different combinations.
Fig. 8 shows all the dip switches are in “off” positions. Each combination corresponds to a delay
off setting.
0000 delay off time = 1 minutes
1000 delay off time = 2 minutes
0100 delay off time = 5 minutes
1100 delay off time = 10 minutes
0010 delay off time = 15 minutes
1010 delay off time = 20 minutes
Fig. 8 Dip Switches in 0000 Positions

Product Description of BRT-310 Page 6of 7
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
0110 delay off time = 25 minutes
1110 delay off time = 30 minutes
0 = off and 1 = on
(Other factory settings are available. Please talk to our sales representatives).
2. Learn the IR remote control codes
Please refer to Fig. 9 and follow the following steps to have BRT-310 PIR remote control learn
and memorize the IR control codes from IR remote controls sets of appliances.
Fig. 9 Learn IR Remote Codes
a. Turn on power to BRT-310 PIR remote control, and set dip switch 4 to ON position.
There is an LED flashing behind the PIR lens;
b. Press and hold the button for code learning until the LED is constantly on;
c. Point the regular IR remote control of appliance to the PIR lens, and start to send OFF
control signals;
d. If the LED quickly flashes a few times, code learning has been successfully completed;

Product Description of BRT-310 Page 7of 7
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
e. To verify if code learning is successful, press the button for code learning to have
BRT-310 PIR remote control send out the control signals it just learned. The appliance
should be turned off accordingly; and
f. Return dip switch 4 to OFF position.
Now, BRT-310 PIR remote control is ready to control the appliance automatically.
Applications:
BRT-310 PIR remote control can be used for automatically turning off various loads which use IR
remote controls, such as lights, fans, appliances, or other kinds of electrical equipment. They are
perfect for saving energy and bringing convenience and safety to our daily life and work.
They have wide applications at various locations such as stairwells, corridors, washrooms, offices,
conference rooms in homes, schools, laboratories, hospitals, offices, etc.
How to Order:
Please contact us: Shenzhen Asia Bright Industry Co., Ltd
Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China
Tel: [phone] [phone]
Fax: [phone] [phone]
Email: [e-mail] Website: www.a-brt.com