teko Astra-531 Ver.PIR User manual

Astra-531 Ver.PIR (Surface Lens)
Optic-Electronic PIR Motion Detector
Operation Manual
The present operation manual is intended for studying operation
principle, running conditions and maintenance of PIR motion de-
tector Astra-531 ver.PIR (hereinafter “detector”) (Figure 1).
The manufacturer reserves the right to make alteration regarding
refinement of the product without prior notification. All changes
will be imported into new edition of the operation manual.
1 Function
1.1 Detector is intended to detect
unauthorized access into an enclosed
protected area, and to generate an alarm
notification by opening alarm relay contacts.
1.2 Power supply of detector is performed
from any direct current source with nominal
voltage 12V and pulsation amplitude not
exceeding 0,1V.
2 Principle of Operation
Detector operation principle is based on registration of thermal
background change of the room occurring on crossing sensitive
zones by a man. Detector sensitive zones are formed by Fresnel
lens and bi-areal pyroelectric radiation receiver. Pyroelectric re-
ceiver sends electric signal to microcontroller, which in its turn
generates an “Alarm” notification by opening of output circuit of
optoelectronic relay in accordance with pre-set algorithm.
Figure 2
3 Specifications
Technical Parameters of Optical Channel
Maximal detection range, m .........................................................5
Viewing angle in horizontal plane, deg., not exceeding..............30
Viewing angle in vertical plane, deg., not exceeding..................95
General Technical Parameters
Power supply voltage, V.........................................from 8 up to 15
Current consumption in „Alarm‟ and Stand-by mode, mA, not ex-
ceeding.......................................................................................18
Technical readiness time, s, not exceeding...................................60
Stand-alone mode start duration, s, not exceeding........................10
Permissible current of signaling relaycircuit, A, not exceeding....0.08
Permissible voltage on relay contacts, V, not exceeding..........100
Relay circuit resistance in Stand-by mode, Ohm......from 6 up to 8
TMP circuit permissible current, A, max..................................0.05
TMP circuit permissible voltage, V, max.....................................72
Overall dimension, mm, not exceeding........................... 62х37х27
Detector weight, kg, not exceeding .........................................0.03
Running Conditions:
Temperature range, °C ................................... from - 20 up to + 50
Relative air humidity, %.....................................up to 95 at +35 °С
without moisture condensation
4 Delivery Set
PIR motion detector Astra-531 ver.PIR..................................1 pcs
Bracket ..................................................................................1 pcs
Screw 2,9х25 (or 2-3х30) ......................................................2 pcs
Dowel 5x25............................................................................2 pcs
Jumper...................................................................................2 pcs
User Instruction....................................................................1 copy
5 Structure
Structurally, the detector is designed as a unit, consisting of a
base and a removable cover. Installed inside the unit is a printed
circuit board with radio elements and screw terminals block for
external wire connections (see figure 3).
Figure 3
Figure 1
Indication start
Cover removed
PIR plug
Tamper switch
Mem plug
Mounting
holes
LED
Wire entry hole
PIR sensor
Screw
terminals
Base
Side view
Top view
2.5 m
5 m
5 m
5 m
0
5m

531-ikv5_4_en
6 Information Capacity
Table 1 - Events and notifications to LED and relay
Event type
LED
Relay
Stand-by
mode start
Flashes 1 time per 1s after
power up.
Duration up to 60s
During up
to 60s
Norm
Not lit
Alarm
Lights up 1 time for 4s at
detection of man movement in
detection zone (when
indication is enabled)
Relay
opens for
4s
Alarm in the
“Alarm
memory”
mode
Figure 4
Relay
opens for
4s
Tampering
Not lit
ТМР
Low power
supply
voltage
Flashes 1 time per 5s at vol-
tage decrease below 8V
"" –relay closed, " " –relay opened
Figure 4
7 Operating Modes
Table 2 –Operating modes and settings
Operation mode
Plug name
Jumper position
High detectability
Normal detectability
PIR
+
–
“Alarm memory” ON
“Alarm memory” OFF
Mem
+
–
“+” - jumper is installed on both plug pins
“-” –jumper is removed (or installed on one plug pin)
The “Alarm memory” mode allows registering the fact and
number of zone violations in prortected area, and is reflected in
corresponding notification .
The mode is activated in 1 minute after installation of Mem plug
or in 1 min. after starting of detector stand-by mode with jumper
installed previously on Mem plug. “Alarm” notification is indicated
in 1 min. after violation of protected area. To switch the mode off
and reset indication, remove jumper from Mem plug or switch
power off.
PIR plug allows changing value of actuation threshold with
regard to different operating conditions.
8 Installation Procedure
8.1 Works on installation, mounting, maintenance and operation
of detector should be performed by only qualified persons.
8.2 After transportation in conditions differing from those of oper-
ation keep detector unpacked under supposed operation condi-
tions for at least 4 hours.
8.3 Selection of installation place
8.3.1Installation on ceiling, on a wall, in window openings and
between window frames is allowed.
8.3.2Installation place should avoid exposure to sunlight.
8.3.3Installation over a high-powered source of heat is not al-
lowed.
8.3.4Avoid installation in presence of objects with rapidly chang-
ing temperature (heating, radiators, air conditioners, stoves,
chimneys, etc.).
8.3.5Wires of signaling zones and power supply circuits should
be located far from power cables.
8.3.6While installing the detector one should take into account
that in case of presence of such obstacles as curtains, screens,
large-scale objects, furniture, plants, etc. within detection zone,
non-sensitive zones (“blind zones”) behind those obstacles are
appeared, detector may fail to detect man movement through
such zones.
1s
1s
2s
1s
1s
2s
2s
Door
LED on
LED off
Number of violations (up
to 3)
Reiterated indication
start
2s
2s
2s
2s
2s
2s
0.5s
0.5s
0.5s
Indication start
4s

531-ikv5_4_en
8.4 Installation procedure
Step-1 Push out cover lock
from base slot.
Remove the cover
Step-2 Unbend hooks
of the base. Remove PCB
Step-3
Extrude plugs of wire entry
hole
Step-4 Choose an appropriate installation option: aor b
Step-5a
INSTALLATION ON A
WALL
Step-5b
INSTALLATION WITH
BRACKET
Step-6а
Make markings on installa-
tion wall surface by applying
the base at an appropriate
height.
Detector base should be
positioned strictly as per
figure of the step 5a
Step-6b
Make markings on installation
place by applying the bracket
at an appropriate height.
Fix the bracket on a wall or
ceiling
Mounting holes
Step-7a
Lead wires from power
supply source and signal-
ing zones through wire
insertion hole in the base.
Fix the base on the wall.
Proceed with step 9
Step-7b
Align the tabs of the base with
the bracket ball slot and partially
screw the screw from the inside
of the base of the detector into
theball.
Choose the appropriate direc-
tion of the detector and tighten
the screw. Bracket provides
for rotation of the detector in
the horizontal and vertical
planes at 40 º
Step-8
Lead wires from power supply source and signaling zones
through wire insertion hole on the base
Step-9
Install the PCB by aligning the
slots of it with the guide tabs of
the base. Push the PCB until it
stops (click)
Step-10
Connect wires led to detector
terminals
Step-11
Remove jumpers from PIR and
Mem plugs
Step-12
Re-install the cover. Power up the
detector.
Step-13
Test the detector. Simulate violator‟s moving with a speed of
0,3 m/s and 3 m/s through detection area. Make sure the
"Alarm" notification is issued with each pass.
Step-14 Remove the cover
Extrude
plugs of
selected
mounting
holes
Extrude the
plug of the
slot for
bracket
attachment
hook
ball
a
b
c
setscrew
screw
slot
tab
ball

531-ikv5_4_en
Step-15 Install jumpers on PIR
and Mem plugs depending on
selected on-site operating mode
Step-16 Re-install the cover
8.5 To provide fail-safe operation of alarm system it is
recommended to carry out testing and maintenance of the
detector at least 1 time per month.
Testing should be carried out as follows:
-Perform moving through detection zone;
-Check output of "Alarm” notification on control panel and on
LED if indication is enabled (LED lights on 1 time for 4s with
every pass).
Maintenance should be performed as follows:
- inspect integrity of the detector‟s body, reliability of wire
connections, detector fixation; clean detector from contamination.
9 Labeling
On the label, pasted to the case, are specified:
–abbreviated name of the detector
–firmware version
–date of manufacture (month and year (last two digits)
–bar code duplicating the textual information.
10 EC Conformity Declarations
This product is in conformity with the provisions of:
EMC 89/336/EEC.
EN 61000-6-3:2005 Electromagnetic compatibility (EMC) –
Part 6-3: Generic standards - Emission standard for residential,
commercial and light-industrial environments.
EN 50130-4/1995 + A1:1998 + A2:2003 + Corrig. 2003 Alarm systems -
Part 4: Electromagnetic compatibility - Product family standard: Immunity
requirements for components of fire, intruder and social alarm systems.
EN 60950-1: 2001+A11:2004+Corrig.2004 Safety of information
technology equipment.
11 Recycling
Detector is not dangerous for life and health of people and is safe for
environment, after termination of service life it should be recycled without
special environment protective measures.
12 Warranty
12.1 Quality Management System meets provisions of ISO 9001-2011.
12.2 The manufacturer guarantees the compliance of the detector to
specifications on condition that user observes required conditions of
transportation, storage, installation and operation
12.3 The storage warranty time is 5 years and 6 months from the date of
manufacturing.
12.4 The operation warranty time is 5 years from the date of operation
start-up but no longer than 5 years 6 months from the date of manufacturing.
12.5 The manufacturer commits to replace or repair the product during
the warranty period.
12.6 The warranty does not come into effect in following cases:
-operation manual is missing;
-mechanical damage of the product;
-repair of the detector by any other party except the manufacturer.
12.7 Warranty applies to the detector only. An equipment of third-party
manufacturers used in conjunction with the detector (including batteries)
is subject to its own warranty terms and conditions
The manufacturer bears no responsibility for death, injury, damage
of property or any other kinds of accidental or premeditated dam-
ages, based on user’s statement that device failed to implement its
function.
Sales:
Controlex GmbH
Warranty service and
technical support:
ТЕКО-TD
Philosophenweg 31-33
47051 Duisburg, Germany
Phone: +49 (0) 203 / 393 91 188
Fax: +49 (0) 203 / 393 91 189
GSM: +49 (0) 178 / 218 48 22
E-mail: [e-mail]
Web: www.controlex.eu
Prospekt Pobedy str. 19
420138 Kazan, Russia
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
[e-mail]
Web: www.teko.biz
Made in Russia
High detectability of
IR channel
Normal detectability
of IR channel
Alarm memory is
ON
Alarm memory is
OFF