IQ-group E-489B Assembly instructions

E-489B
IQ Europe Limited
Sandbeck Lane, Wetherby LS22 7TW.
Visit us at www.iq-europe.co.uk
Installation helpline 0871 717 1100
INSTALLER GUIDE
Bosun "Options" 60W Steel Lantern
V2.0 -1/07
IQ-SNL-SL01-100

MANUFACTURER'S EXTENDED WARRANTY
In addition to your statutory rights relating to this product it is also guaranteed by IQ (Europe)
Limited ("IQ") for 12 months from the date of purchase against faulty materials or workmanship
which affect its designed ability to detect or switch. During this period if the product has a defect
of this nature it will be repaired or replaced free of charge by IQ with the same item, or a similar
one of higher specification, ON CONDITION THAT:-
The buyer takes advantage of any 'return to store' scheme operated by the seller from whom it
is bought.
If the product has a defect outside the period of any seller's 'return to store' scheme it should be
returned to IQ (Europe) Limited at Sandbeck Lane, Wetherby, W. Yorks LS22 7TW, England at
the expense of the buyer together with evidence of the date of purchase (it is the responsibility of
the buyer to prove delivery to IQ).
The product has been bought by the user.
The product has not been misused or handled carelessly, installed incorrectly, or used on a
voltage supply other than that shown on it.
Repairs have not been attempted by anyone other than IQ's staff.
The product has been used for domestic purposes only.
The product has not been installed in any unusually exposed or harsh environmental conditions.
If the buyer is resident in the EU the product or its replacement will be returned to the buyer at
the expense of IQ.
This guarantee excludes liability for discolouration of paint or plastic, or any user replaceable
parts and in particular lamps, glass panels, or globes/lanterns. It does not confer any rights other
than those expressly set out above and does not cover any claims for consequential loss or
damage.
This guarantee is offered as an additional benefit and does not affect your statutory rights as a
consumer.
This contract is subject to the laws of England and Wales.
*** IMPORTANT ***
As of 1 January 2005, changes to the Building Regulations affect domestic electrical installations in
England and Wales. You don't need to be a qualified electrician to make changes to your home's electrical
system, but the work must be done in accordance with the Regulations.
Where you employ an electrician who is a member of a competent person self-certification scheme, they
will be able to certify the work complies with the Regulations.
If you decide to carry out the work yourself we recommend that you make yourself aware of the Regulations
before you begin and if you require any clarification you should contact your Local Authority Building
Control Department.
Details of the Building Regulations can be obtained on the internet via the government website www.odpm.
gov.uk/explanatory-booklet

SECTION ONE
GENERAL INFORMATION
Thank you for buying this IQ OPTIONS light fitting and we hope you will be fully satisfied with
your choice. For your own safety you should read this leaflet before using your unit as it offers
advice and precautions for installation and use.
The OPTIONS range of light fittings are attractive and useful products in their own right but
in addition they also offer you something more than your average light fitting. Each and every
OPTIONS light fitting is manufactured with the capability to accept the OPTIONS Sensor Module;
sold separately. Installation of this Sensor Module converts the light fitting from a manual into an
automatic unit with three different control OPTIONS for you to select from. Without the OPTIONS
Sensor module fitted you will need to manually turn your light fitting on and off as and when you
need it. With the OPTIONS Sensor Module fitted you can forget about having to remember to
switch the unit on or off as the sensor module will do this for you.
The OPTIONS Sensor Module can be fitted at any time, before during or after the installation of
your OPTIONS light fitting. It takes just a couple of minutes to fit, all you need to do is remove
the cap and slide the Sensor Module into place, once inserted it will lock in position. Your next
step is to choose from the three different operating control modes available on the Sensor
Module.
Once the OPTIONS Sensor Module has been installed you can choose from the following
Night Sensor; the unit will illuminate at a level of darkness set by you, and will remain illuminated
throughout the night, switching itself off at dawn. This mode is ideal for use with low energy
lamps but check your OPTIONS Light Fitting to see if Low Energy lamps are capable of being
installed.
Motion Sensor Mode; the unit will begin to operate at a level of darkness set by you,
illuminating only when the sensor detects movement. The unit will then remain illuminated for a
period set by you, returning to the off position when activity ceases. This mode is ideal if you just
want light when its needed.
Night & Motion Sensor Mode; the unit will operate as per the Motion Sensor mode except that
at dusk the unit will illuminate to a dimmed level set by you (0-50%), switching to full brightness
when motion is detected, returning to the dimmed level when activity ceases and switching off
completely at dawn. This mode is ideal if you want a little bit of light to enhance the night time
appearance of your home but with more light being automatically available when movement is
detected.
Your selection of an OPTIONS light fitting was a good choice in its own right, but it can be a
great choice if you combine it with the OPTIONS Sensor Module.
OPTIONS the range of lighting products that provide you with more choice and more control
OPTIONS Allows you to mix and match manual and automatic units, and to switch between any
one of three differing control modes depending on location or preference.
Remember you can install an OPTIONS Sensor Module at any time, so the next time you visit
your local OPTIONS retailer why not convert to automatic.

It is recommended that the lamp is fitted before the lantern is fixed to the wall.
Fit the lamp as follows.
Release the hexagonal nuts on the top cover of the lantern see Diagram A and remove the top
cover.
IMPORTANT!
If you intend to benefit from the addition of the OPTIONS module, please refer to the OPTIONS
control module instruction manual for advice on assembly and set up.
If you intend not to use the OPTIONS module,the blanking plate MUST be fitted to maintain
Safety Regulations!
Fit Blanking Plate supplied by simply inserting into the aperture shown on diagram B. Ensure
blanking plate is fully secured to ensure a watertight seal. There will be an audible click and the
cover will fit securely into its circular aperture.
If the blanking plate is missing from this product, DO NOT INSTALL, please contact the
Consumer Helpline below.
SECTION TWO SELECTING THE LOCATION
If it is your intention to use the OPTIONS control module, for best results mount at height of
1.8m. See OPTIONS module instruction manual for more details.
SECTION THREE INSTALLATION
After choosing a suitable location (see previous section) install the unit as follows:
The unit is suitable for connection to a 240V 50Hz electricity supply. It is suggested that
3-core round flexible cable of 1mm² gauge is used. An internal switch should be installed to
switch the power to the unit ON & OFF. This allows the lantern to be easily switched off when not
required or for maintenance purposes.
*** IMPORTANT ***
Switch off the electricity at the fuse box by removing the relevant fuse or switching off
the circuit breaker before proceeding with the installation.
PARTS INCLUDED
- Luminaire
- Instruction manual. Please keep safe for future reference.
- Wall fixing screws and wall plugs
- Blanking Plate
- Wall plate
TOOLS & PARTS NEEDED
- Electric/hand-held drill & bits.
- Terminal or Electricians screwdriver
- Large slotted/philips screwdriver
- Wire cutters
- 1.0mm sq. round flexible cable
- 60W Max GLS ES Lamp (refer to Section 5 for further details)
This lantern is for outdoor use only. Unit must be mounted on a non-flammable surface as a
fixed luminaire, and is not suitable for portable use.The unit can get very hot during use. Ensure
the unit has cooled before handling.Ensure adequate ventilation space is allowed between the
unit and any object above, in front or to either side of the unit. Suggested space is 0.5m above,
0.3m to either side & 1.0m in front. Do not attempt to install during wet weather, if you are
suffering from nausea or dizzy spells or on medication with similar side effects
If in any doubt, consult a qualified tradesperson or electrician.

CONNECTION
It is recommended that the circuit is protected by a 5A max fuse or circuit breaker.
It is recommended that this product is connected to fixed wiring only.
Connect the cable to the terminal block on the unit as follows (see connection diagram):
LIVE (Brown) L
EARTH (Green/Yellow)
NEUTRAL (Blue) N
Ensure that the connections are secure and the terminal block is securely located on its mounting
posts.
This product uses a fast fix connector and it is imperative the connector is aligned when
assembling the lantern onto the wall plate.
Lift the lantern onto the wall plate, ensure that the screws at either side of the lantern bracket
are aligned with the holes in the wall plate, this will ensure the pin connections of the fast fix
connector are aligned with their receptacles.
Replace the top cover and secure the two fixing screws.
Ensure the decorative "handle" is located in the slot at the rear of the lantern.
Fully secure the lantern fixing screws See Diagram A.
Installation is complete.
The unit is ready for mounting to the wall.
The wall bracket is packed seperately, remove from packaging.
Based on the location of your incoming cable,use the wall plate as a template and mark the
position of the mounting holes. See diagram C.
Ensure the wall plate is in the correct orientation by referring to the to arrow marked "TOP" See
Diagram C, note that the wall plate is placed in a VERTICAL position for this product.
Drill holes and insert wall plugs into the holes.
Pierce and pass the cable through the grommet before securing the wall plate to the wall.
Fit the wall plate to the wall
Do not overtighten, if using a power screwdriver ensure it is set to the lowest torque setting to
prevent damage to the wall plate.
CONNECTION DIAGRAM
Mains
Supply
Isolation
Switch
N
E
L
N
E
L

SECTION FOUR
OPERATION AND TESTING
Turn on the power to the lantern, the lamp should illuminate.
If you have purchased the OPTIONS Module, please refer to the "Operation and Testing section
of the OPTIONS module manual.
If you have any problems, please refer to the troubleshooting guide and Technical Helpine details
below.
SECTION FIVE
TECHNICAL SPECIFICATION
If you experience problems refer to Troubleshooting Guide.
If problems still exist, do not immediately return the unit to store.
Telephone the IQ Customer Helpline
0871 71 71 100 Weekdays 9.00am - 5.00pm
[email protected] www.iq-europe.co.uk
Qualified Customer Support Co-ordinators will be on-line to assist in resolving your query.
SECTION SIX
TROUBLESHOOTING GUIDE
PROBLEM
Lantern did not operate at all. SOLUTION
Check that the power is switched ON at the circuit breaker/
internal wall switch.
Turn OFF the power to the unit and check the wiring
connections as per the diagram (see previous section 3).
Ensure no connections are loose.
Check the lamp. If the lamp has failed, replace. Ensure that
the lamp is seated correctly in the lampholder.
IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN.
IF OPTIONS MODULE IS USED PLEASE REFER TO THE
TROUBLESHOOTING GUIDE IN THE OPTIONS MODULE
MANUAL.
Power Supply
Maximum Switchable Load
Environmental Protection
230 - 240V AC ~ 50Hz
60W GLS or Equivalent CFL ES Energy Saving lamp.
IMPORTANT! If using the OPTIONS Module, please
refer to its instruction manual for important information
when using Energy Saving Lamps
IP44 Suitable for outdoor use

NEL
A
D
C
B
hexagonal cover fixing
nuts and washers x 2
blanking
plate
lantern fixing
screw x 2
fast fix connector
wall fixing hole
wall fixing hole
cable inlet
LEN

?
DID YOU KNOW...
IQ products are designed and manufactured to give many
years of trouble-free service.
The materials used during manufacture have been select-
ed to improve their ability to be recycled when the product
is no longer functional.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling
advice
SAVE MONEY & HELP THE ENVIRONMENT
Consider using smaller wattage lamp. This could save you
up to 40% in running costs, whilst also conserving pre-
cious natural resources.
LIGHT POLLUTION & CONSIDERATE LIGHTING
Please be aware of the annoyance over-lighting an area
can cause to your immediate neighbours.
Light pollution caused by incorrectly installing a lantern or
over-lighting an area can be limited by carefully considering
the location and position of your lantern before installation.
Please try to concentrate the light on your property and
limit the potential inconvenience of the light shining into
your neighbours windows etc.
Please see Selecting a Location for information on choos-
ing the optimum location for your lantern