IQ-group E-997 Assembly instructions

INSTALLER GUIDE
Lantern Receiver
E-997
IQ Europe Limited
Sandbeck Lane, Wetherby LS22 7TW.
Visit us at www.iq-europe.co.uk
Installation helpline 0871 717 1100
V1.0 - 04/05
IQLA-BC-RX-W
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 1

MANUFACTURER'S EXTENDED WARRANTY
In addition to your statutory rights relating to this product it is also guaranteed by IQ (Europe)
Limited ("IQ") for 12 months from the date of purchase against faulty materials or workmanship
which affect its designed ability to detect or switch. During this period if the product has a defect
of this nature it will be repaired or replaced free of charge by IQ with the same item, or a similar
one of higher specification, ON CONDITION THAT:-
The buyer takes advantage of any 'return to store' scheme operated by the seller from whom it is
bought.
If the product has a defect outside the period of any seller's 'return to store' scheme it should be
returned to IQ (Europe) Limited at Sandbeck Lane, Wetherby, W. Yorks LS22 7TW, England at
the expense of the buyer together with evidence of the date of purchase (it is the responsibility of
the buyer to prove delivery to IQ).
The product has been bought by the user.
The product has not been misused or handled carelessly, installed incorrectly, or used on a
voltage supply other than that shown on it.
Repairs have not been attempted by anyone other than IQ's staff.
The product has been used for domestic purposes only.
The product has not been installed in any unusually exposed or harsh environmental conditions.
If the buyer is resident in the EU the product or its replacement will be returned to the buyer at
the expense of IQ.
This guarantee excludes liability for discolouration of paint or plastic, or any user replaceable
parts and in particular lamps, glass panels, or globes/lanterns. It does not confer any rights other
than those expressly set out above and does not cover any claims for consequential loss or
damage.
This guarantee is offered as an additional benefit and does not affect your statutory rights as a
consumer.
This contract is subject to the laws of England and Wales.
*** IMPORTANT ***
As of 1 January 2005, changes to the Building Regulations affect domestic electrical installations in
England and Wales. You don't need to be a qualified electrician to make changes to your home's electrical
system, but the work must be done in accordance with the Regulations.
Where you employ an electrician who is a member of a competent person self-certification scheme, they
will be able to certify the work complies with the Regulations.
If you decide to carry out the work yourself we recommend that you make yourself aware of the
Regulations before you begin and if you require any clarification you should contact your Local Authority
Building Control Department.
Details of the Building Regulations can be obtained on the internet via the government website
www.odpm.gov.uk/explanatory-booklet
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 2

SECTION ONE
GENERAL INFORMATION
This Lantern Receiver must be used in conjunction with suitable IQ Transmitter units in the IQ
Wirefree range.
Upon detection of a signal from a transmitter (bought separately) this Lantern Receiver will react
as programmed.
PLEASE NOTE:- PLEASE SEE THE SEPERATE INSTRUCTION MANUALS FOR THE
TRANSMITTER PRODUCTS TO UNDERSTAND HOW TO PROGRAM AND ADJUST THAT
SPECIFIC TRANSMITTER.
THIS MANUAL COVERS THE INSTALLATION OF THIS SPECIFIC LANTERN RECEIVER
ONLY
PARTS INCLUDED
- AC Lantern receiver unit
- Instruction manual. Please keep safe for future reference.
The Lantern receiver must be used indoors and can be placed inside any household lamp using
a BC lamp holder. It must be placed within transmission range of the PIR Transmitter. (See later
sections for details).
SECTION TWO
LANTERN RECEIVER:- INSTALLATION
The Lantern Receiver (Rx) must be within transmission range of your PIR transmitter.(Tx). We
suggest that firstly, that the Tx is placed in its optimum position to give the coverage and
detection required, then the Receiver is located indoors at a point where it can receive the Tx`s
signal.
1. Position your PIR Tx in desired area, perform walk tests to confirm detection zones.
2. Chose your preferred location for the Lantern Rx up to 60m away (free air space) from the Tx,
take into account the path between the sensor and receiver to ensure range is acceptable as the
range can be reduced by metal objects, walls etc.
Turn the light fixture OFF and fit the Lantern Rx into the light fixture as you would fit a standard
BC lamp. Fit a 60W BC incandescant lamp or Max 27W Compact Fluorescent Lamp into the
receivers socket.
The Lantern Receiver is designed for both Pendant Lamps (suspended from ceiling) and table or
standard lamps (normal orientation) and can also be fitted to uncontrolled outdoor decorative
lanterns if there is sufficient space. See diagram B
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 3

Lantern Receiver Controls
B
A
Lantern Receiver orientation
ON TIME
AFTER
DETECTION DUSK TIMER
Program (reset)
Button
LED
Lantern Receiver in
Table/Standard
Lamp
Lantern Receiver in
Ceiling Socket
SECTION THREE
LANTERN RECEIVER OPERATION AND TESTING
Auto Programming
Once the PIR Transmitter (TX) and Lantern Receiver (RX) are installed, the Receiver needs to
learn the coded signal transmitted from the Transmitter.IQ makes this easy with its Auto
Programming function.
See diagram I
1.Set the Lantern Receiver ON TIME DIAL to TEST
2.Set the Lantern Receiver DUSK TIMER to OFF
3. Turn the light fixture ON.
4. When the Lantern receiver first powers up, the light will remain off for a short period. After this
short period the light comes ON to indicate the programming period has begun, the Lantern RX
LED will flash slowly. See diagram I.
5. To activate the Sensor`s signal to the Receiver, walk in front of the Sensor. the Sensor`s LED
flashes red indicating motion has been sensed and a signal has been transmitted. The lamp will
now illuminate for 5 seconds after each detection and the RX LED will flash slowly.
6. The Lantern receiver acknowledges this signal by turning the light OFF. The Receiver is now
programmed to respond to the sensor. The RX LED will remain constantly ON.
REMINDER: the light fixture needs to stay in the ON position for the Lantern Receiver to
remain in AUTO MODE. No other transmitter can activate this light unless you program
another transmitter to do so.
Go to step 8.
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 4

7. If the light did NOT GO OFF, the Lantern Receiver is not picking up a signal from the TX. Check
the radio signal path between transmitter and receiver for any metal obstructions (support beams,
aluminum window casings etc). these can block the radio signals and interfere with signal
transmission. To determine a clear signal path, move the Lantern Receiver to different outlets and
activate the Transmitter. Locate the Lantern Receiver in an outlet where the Transmitter activates
it.
8. Remove the sticker from the photocell on the DC PIR Transmitter.
Lantern Receiver Settings
After Auto Programming is complete, the ON TIME and DUSK TIMER can also be set:-
1.ON TIME
The ON TIME setting determines how long the light will remain ON after motion has been sensed
by the DC PIR TX. Turn the ON TIME dial to 1, 3, 5 or 12 minutes.
PLEASE NOTE THAT THE LANTERN RECEIVER IS DESIGNED TO TURN THE LIGHT ON IN
DAYLIGHT AS WELL AS NIGHT IF MOVEMENT IS DETECTED.
THE LIGHT WILL REMAIN ON FOR THE LENGTH OF TIME SET BY THE USER AND THE LED
WILL FLASH ON/OFF FOR APPROX. 5 SECONDS
IF FURTHER MOVEMENT IS DETECTED WHILST THE LIGHT IS ILLUMINATED, THE LIGHT
WILL BLINK OFF QUICKLY AND THEN TURN BACK ON FOR THE LENGTH OF TIME SET BY
THE USER AND THE LED WILL FLASH ON/OFF FOR APPROX. 5 SECONDS
2. DUSK TIMER.
To set how long the light remains ON after dusk, set the DUSK TIMER dial to 2, 4, 8, hours or
DUSK/DAWN.
After dusk, the light will turn on in DIMMED MODE for the time you set.
If motion is detected by the DC PIR TX, the light turns ON for the length of time you have set using
the ON TIME dial then will return to DIMMED MODE..
WARNING!!
If you decide to use a Compact Fluorescent Lamp (CFL) in the Lantern Receiver, you MUST
set the dials as follows:-
ON TIME DIAL to 3, 5 or 12 minutes. DO NOT SET TO 1 minute as a CFL can be damaged
by short term switching on and off.
DUSK TIMER to OFF position as it is NOT possible to use the dim fuction with a CFL .
In this case the Lamp will remain OFF until it is activated, then will remain on for the
duration set by the ON TIME DIAL.
Manual Override.
To turn the light fixture on manually, flip the mains switch off/on within one second and the lamp
will illuminate permanently at full power.
The return the Receiver to Auto Mode repeat the same action.
ADDING ADDITIONAL TRANSMITTERS TO CONTROL THE LANTERN RECEIVER
The Lantern Receiver can be programmed to operate with up to 16 additional Transmitters. These
products are easily added to expand your system.
To add additional Tx`s, press the Rx PROGRAM button for 1 second while the Rx is powered.
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 5

DO NOT PRESS FOR LONGER THAN 2 SECONDS AS YOU MAY ERASE ALL EXISTING
CODES.
The light will turn ON, indicating the Lantern RX is in PROGRAM MODE and will remain ON up to
5 minutes. During this time, activate the Transmitter you are adding to send its code to the Lantern
Receiver and the light will go off. This code is stored in the Lantern Receiver along with existing
codes and the Lantern Receiver will now respond to the additional Transmitter.
Erasing All Codes.
Tx codes can be erased for reprogramming. To erase codes, while RX is powered, press and hold
the PROGRAM button for more than 5 seconds. The light will turn on, go out briefly then turn on
again. This will clear the Rx of all programmed codes and place it into the AUTO PROGRAMMING
Mode.
Note:- to prevent inadvertent programming by other transmitters, remove then gradually add
batteries or turn on power to the Tx you want coded to the Chime Rx during the AUTO
PROGRAMMING Mode.
SECTION FOUR
TECHNICAL SPECIFICATION
LANTERN RECEIVER
Power Supply
Maximum Switchable Load
Time On Adjustment
Dusk Timer Adjustment
Dimmer
Transmission Range
230/240 V AC ~ 50Hz
75W Max BC GLS or 23W Compact Fluorescent Lamp
(CFL)
1, 3, 5, 12 minutes (3, 5, 12 minutes for CFL)
2, 4, 8, hours and Dusk to Dawn.
Fixed at 30% of full power(
(NO DIM function if using a CFL)
Up to 60m (varies with surrounding structures)
If you experience problems refer to Troubleshooting Guide.
If problems still exist, do not immediately return the unit to store.
Telephone the IQ Customer Helpline
0871 7171100 Weekdays 9.00am - 5.00pm
[email protected] www.iq-europe.co.uk
Qualified Customer Support Co-ordinators will be on-line to assist in resolving your query.
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 6

SECTION FIVE
TROUBLESHOOTING GUIDE
PROBLEM
oLamp stays ON all the time at
night.
oPIR keeps activating for no
reason / at random.
oPIR sensor will not operate at
all.
oThe PIR sensor will not
operate at night.
oPIR coverage is poor/sporadic
o Detection range varies from
day to day
SOLUTION
The unit may be suffering from false activation. Cover the
sensor lens completely with a thick cloth. This will prevent the
sensor from "seeing" anything. If the unit now switches off
after the set time duration and does not re-activate, this
indicates that the problem was caused by false activation. The
problem may be solved by slightly adjusting the
direction/angle of the sensor head (see previous section).
You may not be allowing the unit time to complete it's
warm-up period. Stand well out of the detection range and
wait (the warm-up period should never exceed 1½ minutes).
Occasionally, winds may activate the sensor. Sometimes
passages between buildings etc. can cause a "wind tunnel"
effect.
Ensure the unit is not positioned so as to allow detection of
cars/people using public thoroughfares adjacent to your
property.
Check that the batteries are in good condition and fitted
correctly
Unit may be poorly located. See previous section - ‘Selecting
The Location’ and re-locate the unit.
PIR sensors are influenced by climatic conditions. The colder
the ambient temperature, the more effective the sensor will
be. You may need to make seasonal adjustments to the
sensor head position to ensure trouble-free operation all year
round.
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 7

Problem
oChime/light did not activate when motion is
sensed.
o Chime/light activates in daylight
LANTERN RECEIVER IS DESIGNED TO
OPERATE IN DAYLIGHT.
oDC PIR TX LED flashes on and off 5 times
when activated.
oLantern receivers light flashes on and off twice
when activated.
oTone/Light activates for no apparent reason
Possible cause/solution
1. Socket switch is turned off.
2. Re-aim sensor to cover desired area.
3. Turn Sensitivity Knob to maximum
4. Photocell determines it is daylight.
Move away from light source.
5. Sensor is too far from Receiver.
Move closer.
6. Metal on building, chain link fence, etc.
blocking path of Sensor’s signal
transmission. To check signal path, set
Receiver’s on time dial to Test. Remove
Sensor from bracket (recover photocell if
daylight). As you walk the Sensor around
the Receiver, wave your hand in front of
Sensor. Note when it turns the Receiver
ON. Remount Sensor in that area.
7. Check the lamp. If the lamp has failed,
replace.
The level of ambient light in the area may be
too bright to allow operation Relocate in a
darker area.
For Chimes
1. Sticker not removed from sensors photocell.
Remove label
2. Sensor installed in dark location. Reposition
Sensor
This is the low battery signal. Replace
transmitter batteries.
This is the low battery signal. Replace
transmitter batteries.
Check area for false activation from heat or
reflective source. Re-aim sensor
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 8

?
DID YOU KNOW...
IQ products are designed and manufactured to give many
years of trouble-free service.
The materials used during manufacture have been select-
ed to allow the product to be easily recycled when no
longer functional.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling
advice
LIGHT POLLUTION & CONSIDERATE LIGHTING
Please be aware of the annoyance over-lighting an area
can cause to your immediate neighbours.
Light pollution caused by incorrectly installing a unit or
over-lighting an area can be limited by carefully considering
the location and position of your unit before installation. The
light spread on all halogen floodlights can be reduced by
angling the floodlight downwards on the mounting bracket.
This will also concentrate the light on your property and
limit the potential inconvenience of the light shining into
your neighbours windows etc.
Please see Selecting a Location for information on choos-
ing the optimum location for your security light.
SF-LA-BC-RX-W.qxd 13/04/2005 13:36 Page 9