IR Dor-O-Matic 96000 Series User manual

Series 96000 Slide Control
Installation Instructions
Dor-O-Matic
DOR - O – MATIC ®
7350 W. Wilson Ave.
Harwood Heights, IL 60706
Toll Free: 1-800-543-4635
In Illinois: 708-867-7400
Sales FAX: [phone]
www.doromatic.com
96010-084 REV. H December 2002 DA-309

INSTALLATION
1. Preparation: Refer to Series 96000 Slide Installation Manual (DOM #96000-984) for header preparation instructions.
2. Final Wiring Connections:
The Series 96000 header comes from the factory “pre-wired” to minimize installation time at the job site. Connect main power to the terminal block
at the end of the header (Figure 1). Connect accessories to the terminal block on the safety beam bracket or the appropriate harnesses as needed
(Figure 2). Refer to the instruction manual of the accessory for complete wiring details.
A. Use a 115 volt, 60Hz, fused, 15 amp, 3-wire power supply. NOTE: Always disconnect
main power to operator prior to
servicing or cleaning.
B. Secure all conductors and connections against physical damage.
C. Route all wiring away from moving parts, sharp edges and heat sources.
D. Use copper conductors only.
FIGURE 1: POWER WIRING DIAGRAM
96010-084 REV. H December 2002 DA-309

FIGURE 2: ACCESSORY WIRING DIAGRAM
3. Operational Check and Adjustments:
NOTE: Refer to the latest revision of ANSI/BHMA A156.10-1999 Standard for Power Operated Pedestrian Doors for all settings and adjustments.
A. Sizing:
If the 4-Position Switch is used, be sure it is in the “2-WAY” position before proceeding. Apply power to the system using the main power
switch on the header/cover. Give the system an activation signal. The door should open and close once, after which it is ready for normal
operation. If the door does not size to the fully open position, first check for binds, then increase the sizing speed by rotating P6 counter-
clockwise just enough to overcome the door weight, etc. Caution: If the door sizing speed is set too fast, blown fuses and/or a tripped
circuit breaker may occur if the doors are activated when manually locked.
B. Opening Speed:
The opening speed is adjusted by rotating P2 (CW=SLOWER, CCW=FASTER). It is recommended that the door be operated as slow as is
practical for the traffic conditions.
C. Closing Speed:
The closing speed of the door is adjusted by rotating P4 (CW=SLOWER, CCW=FASTER) and must not exceed 1 ft/sec.
NOTE: Reset power to the system after setting the opening and closing speeds. This must be done before making any other adjustments.
D. Back Check Location:
The back check location is selected using SW2 (0=MINIMUM, F=MAXIMUM).
E. Back Check Speed:
The back check speed is adjusted by rotating P3 (CW=SLOWER, CCW=FASTER).
F. Latch Location:
The latch location is selected using SW1 (0=MINIMUM, F=MAXIMUM) and must be at least 2 inches from the fully closed position.
G. Latch Speed:
The latch speed is adjusted by rotating P5 (CW=SLOWER, CCW=FASTER).
H. Time Delay/Hold Open Time:
The time delay is adjusted by rotating P1 (CW=LESS DELAY, CCW=MORE DELAY). The adjustment range is 1 to 30 seconds. If a presence
sensor is not installed, the time delay must be at least 4 seconds.
I. Normal/Delayed Activation:
The activation is selected with SW3. In the normal position, the door opens immediately upon reception of the activation signal. In the delayed
position, when the door is fully closed, there is a 1 second delay between reception of the activation signal and the actual opening of the door.
This delay allows most electric or magnetic locks time to retract before the door opens.
J. Auto Reverse in Closing:
The amount of force required to reverse the door when closing is adjusted by rotating P7 (CW=MORE FORCE, CCW=LESS FORCE) and
must not exceed 30 lbs.
K. Auto Reverse in Opening:
The amount of force required to reverse the door when opening is adjusted by rotating P8 (CW=MORE FORCE, CCW=LESS FORCE).
L. Reset Power:
After setting all of the adjustments, reset power to the system. Cycle the door to verify all of the settings are correct. If any settings need to be
changed, be sure to reset power again. Power must be reset after any adjustments are made.
96010-084 REV. H December 2002 Page 3of 5

FIGURE 3: CONTROL BOX & TRANSFORMER BOX ADJUSTMENTS
4. Operational Walk-Through Test:
NOTE: It is assumed that during the installation process, any problems would have been found and corrected before this point. However, it is
recommended that a complete walk-through test now be performed.
A. Give the system an activation signal. The door should open smoothly and silently to the back check point, where it should slow down rapidly
and drift into the fully open position without slamming.
B. Maintain the activation signal to verify that the door does NOT time out and close while being activated.
C. If a door safety device is used, step into the door opening. Remain in the door opening making sure that the door does NOT close.
D. Step out of the door opening. After both the activating area and door opening are clear, the door should time out at the pre-set time delay and
begin to close. The door should close quietly and smoothly to the latch point, where it rapidly slows down and drifts into the fully closed
position without slamming.
5. Release of the System for Use:
A. Remove all tools and installation equipment, and clean any debris from the vicinity of the door.
B. Install all safety, traffic control, and instruction decals to the door as required. THIS IS VERY IMPORTANT! Failure to do this leaves the
installer LIABLE for any accident that might occur. THIS MUST BE DONE!
C. Verbally explain the proper operation of the door system to the owner or to the person in charge.
6. For Doors that are manually/mechanically secured:
A. Locking: 1) Place switch in “OFF” 2) Allow door to close completely 3) Secure door
B. Unlocking inside: 1) Unsecure door 2) Place switch in “1-WAY” or “2-WAY” 3) Activate door once
C. Unlocking outside: 1) Unsecure door 2) Activate morning entry or manually open door 3) Place switch in “1-WAY” or “2-WAY”
96010-084 REV. H December 2002 Page 4of 5

FEATURES
1. Easy Open: When the door is fully closed and manually opened a few inches, it will automatically open the rest of the way.
2. Adjustable Automatic Reversing: If the door is stalled during the closing cycle, it will automatically stop and reverse to the fully open position. Then
the door will close to the point of obstruction and drop to slow speed, looking for the obstruction. This cycle will occur 5 times until the obstruction is
removed. After the fifth cycle, the door will stop, requiring an activation signal or manual opening to re-start the system. If the door is stalled during
the opening cycle, it will automatically stop and reverse to the fully closed position. The door will remain closed until the next activation signal, at
which point it will open normally. Reversing forces should be adjusted in accordance with all applicable safety codes.
3. Weatherwise: The weatherwise feature allows the customer to reduce the opening size. When the weatherwise switch is set to “NARROW”, the
door will only open to about 75% of the normal door opening. (Default = ”WIDE” or 100% opening)
4. Safety Beam Shut-Off: When the door is fully closed, the safety beam signal is disregarded so that it cannot be used to open the door. Once the
door is activated, the safety beam signal is allowed to re-open the door if either safety beam is interrupted during the closing cycle.
5. 4-Way Operation:
When the 4-Position Switch is set to:
“OFF”, interior and exterior activation will not open the door. The morning entry switch will open the door.
“1-WAY”, only interior activation will open the door. Exterior activation will not open a closed door but will re-open a door in the closing cycle.
“2-WAY”, interior and exterior activation will open the door.
“HOLD OPEN”, the door will remain open.
If the 4-Position Switch is not used, Default = “1-WAY”.
DO’S AND DON’TS
1. Do NOT try to use this operator on large, heavy doors without checking with the factory first.
2. Do NOT connect any remote activating device to the door unless it is located within the ”line of sight” of the door.
3. Do NOT attempt to use a fuse larger than specified.
4. Do NOT attempt to modify the factory wiring or connect any wiring into an existing electrical circuit or any other electrical device.
5. Do make certain that the operator is connected to a dedicated 115 volt circuit from the main circuit breaker panel.
6. Do make certain that the operator is properly grounded with a separate green wire.
7. Do make certain that all connections are proper and secure before turning the power on.
8. Do make certain that all wires are properly dressed and secured to prevent any interference.
9. Do make certain that all safety labels and instruction decals relating to door operation are properly applied to the door before leaving the job.
10. Do verbally instruct the owner or person in charge of the proper operation of the door.
11. Do disconnect main power to the operator prior to servicing or cleaning.
12. Do instruct the owner or person in charge of his responsibility of inspecting the door for the following:
A. Occasional damage
B. Developing problems
C. Minor preventative maintenance
Page 5of 5
If the door package operates improperly, turn off main power. Re-adjust all potentiometers to the middle of their range and turn main power on.
Activate the operator to allow the door to re-size. Repeat adjustment procedure as required.
D. Who and where to call for service when required
96010-084 REV. H December 2002