IRIS PERFORMANCE Haisen HD05R User manual

Quick programming
User Manual
Remote controller Haisen HD05R (Iris p/n: RC-HD05R)
Default
setting Application
Scene 100% 5s 0s 10% disabl
eGeneral
To switch between microwave technology and
PIR (Passive InfraRed)
To turn On/Off the luminaire or deactivate the motion sensor function
Buttons for saving the chosen settings and applying them to the
luminaires within reach of the remote
Activates detector/programming mode and restores factory default
settings
Description of main functions
"Scene" button brings back factory
default program
1. Press on
2. Press on by pointing the
luminaire to be programmed with
the remote control
Note: it will always be possible to change parameters afterwards
Popular: MW
Stand-by period
Time before the luminaire turns off
Ambient light detection
Allows you to increase or decrease the values
To increase or reduce the lighting level of the luminaire when a
person is present
Stand-by period dim level
Light level during the stand-by period
Normally:
disable
Holding period
Time to first reduction in light level
Note: « Test (2s) key is not used
Popular : 30 min
Populaire : + ∞
( never turns off)
Popular: from 30% to 50%
Motion sensor detection area
25% = narrow; 100% = wide

Phase 1 : In the absence of movement, the luminaire will hold its
maximum intensity for a selectable duration of 5s / 30s / 1min /
3min / 5min / 10min / 20min / 30min. (hold period)
Phase 0 : As long as a person is detected by the sensor, the
luminaire is at its maximum intensity.
Adjustable lighting level with « Power % »
Phase 2 : If no movement is detected during the hold period, the
luminaire will dim to an adjustable intensity of 10% / 20% / 30% /
50% (stand-by period).
The reduced light level will be maintained for a selectable duration
of 0s / 10s / 30s / 1min / 5min / 10min / 30min / 60min / - -
before going off.
Example:
By adjusting the stand-by period to 0s, the luminaire will turn off directly
after the hold period without going through a reduction in lighting.
By adjusting the stand-by period to - -, the light will keep its intensity
reduced indefinitely without ever turning off in the absence of movement.
Principle of operation
User Manual
Remote controller Haisen HD05R (Iris p/n: RC-HD05R)
Detailed programming procedure
5s →30m
50 %
100 %
DIM +
DIM -
50 %
10 %
0s →∞
LIGHT LEVEL
TIME
LAST MOVEMENT DETECTED BY SENSOR
10 %
PHASE 0 PHASE 1 PHASE 2
Select the motion sensor detection area
note: the wider the area, the faster motion is detected
Select the duration of the hold period
note: if no movement, intensity remains at maximum for this duration
Select the stand-by period dim level
Note: lighting level is a % of maximum intensity
Select the duration of the stand-by period
note: length of time the luminaire remains in reduced lighting before switching off
Disable the function « Ambient light detection »
1- Press to activate programming mode
2- Press on « Start » ( flashes) and press the parameter to be modified
(parameter icon flashes)
3- Press once all parameters have been changed
Modify the parameters using the + or - keys
S
4- Select the motion sensor detection area
note: the wider the area, the faster motion is detected
Procedure
Notes

User Manual
Remote controller Haisen HD05R (Iris p/n: RC-HD05R)
Recommendations for the optimum operation of motion sensors
1- Maintain a minimum distance of 3 meters between motion sensors.
2-
Suspended fixtures should be installed on rods instead of chains to prevent fixture movement. Movement of the luminaire may
trigger false motion detection.
3-
The motion sensor does not differentiate between a human and any other moving objects within its detection zone. So,
beware of fans, forced air heating equipment, conveyors or any other equipment that could create movement on objects and
thus trigger a false detection
4- Large reflective surfaces (metal, concrete or glass) near a motion sensor may cause false detections due to microwave
reflection off these surfaces.
5- We recommend a preliminary installation of a few luminaires to validate the performance of the motion sensors in the project
environment.
6- Caution: The installation of a luminaire equipped with a motion sensor does not replace the installation of a night light for
security. Light fixtures with a motion sensor are intended to reduce power consumption, not to replace a circuit breaker.