IRO Dashcam A66 User manual

IRO Dashcam
Product Manual
for Tesla Model S AP1

Please read this manual completely before beginning your installation.
®
Thank you for your purchase of the IRO Dashcam.
®
Your lRO Dashcam can record up to 1920x1080 full HD video.
Using your smart phone app, you can connect your phone to your
®
IRO Dashcam using the built-in WiFi. You may use your smart
phone to view real time video from your camera, as well as play video,
®
save video, and download video. The IRO Dashcam may be
completely controlled via the smart phone app.
®
Note: We are always working on updating the IRO Dashcam.
If you find any discrepancy in this manual, please use the information
found with the DVR app.
01
Introduction
Your new IRO Dashcam is only for use in Tesla Model S AP1
(Equipped with Autopilot 1.0 system).

Product Structure
Lens
TF card slot
Button 2 & blue light
Button 1 & red light
Button 3
02
Heat emission hole

The black line pin The red line pin
Product Structure
The pin on the black line connects to the black wire of the car power connector.
The pin on the red line connects to the red/yellow wire of the car power connector.
When inserting the pins into the power connector, be sure the pins are gently pushed all
the way into the connector to assure a good connection.
03

Power supply wiring
Insert the pin on the
end of the red wire
from the camera to
the red/yellow wire of
the car power connector.
Insert the pin on the
end of the black wire
from the camera to
the black wire of the
car power connector.
®
The IRO Dashcam is powered from the car ’s rearview mirror. This avoids having to run
®
power wire throughout the car and into the fuse panel. This method of powering the IRO
Dashcam is more streamline, and avoids having to see ugly wires. The TF card is inserted last.
04

Power supply wiring
After inserting the pins into
the car power connector, use
the provided tape strips to hold
the wires in place. This will
prevent the wires from
separating.
®
Be sure that the pins on the wires from the IRO Dashcam are fully inserted and making good
contact before applying the tape. Once the wires are properly connected, you will hear an
®
audible beep from the IRO Dashcam. You will also see the green light indicating the unit is
powered on. If this doesn’t happen, check your wiring to make sure the pins have good contact
with the car power connector and the wires are not loose.
05

Installation video
Installation Video
06
We strongly recommend that you see our installation video before installing.
Please scan the following QR to watch the installation video.

Installation Steps
Before installing
During installation, be careful when
removingthe plastic shell from the
mirror. You don’t want to slip and
hit your arm on thedashboard.
Use both hands to remove the plastic shell
from the mirror base. You may have to apply
downward pressure to remove it.
To remove the power connector, press it in.
The power connector will spring out and is
easily removed.
See pages 3-5 for proper wiring. Apply wires using diagrams provided on
pages 3-5.
07

Installation Steps
Once the wiring is completed, you will
®
hear the IRO Dashcam emit a beep
and see a red light. This indicates
proper wiring.
Use the provided tape strips to hold the
wires in place. This will prevent the wires
from separating. Wrap the tape around
the wires to hold them together.
Plug the power connector back into the
socket from which it was removed.
®
Align the IRO Dashcam to the mirror
base aligning the plastic hooks.
Firmly press the camera into place making
sure all four of the plastic hooks are fastened.
®
The IRO Dashcam should fit snugly as if
it were the original shell. Insert the TF card.
A class 6 TF card is recommended.
Congratulations! Your installation is
complete. Please be sure to keep the
original shell which you removed.
This will allow you to move the camera
to another vehicle in the future and
put your original shell back in place.
08

09
Operation