IS5 COMMUNICATIONS iPJ2G User manual

All specifications are subject to change without notice. QIG-iPJ2G-2-EN.docx Page—1
Quick Installation Guide
iPJ2G
Industrial Gigabit PoE Injector
•Supports 10/100/1000Base-T(X) ports for power
and data output
•Fully compliant with IEEE802.3 af /802.3at
•Auto protection for over voltage power input and
over current output
•Supports power output up to 60Watts at 50VDC
•Supports power input range from 12VDC to 57VDC
•High reliability in rigid IP-40 housing
•DIN-Rail and wall-mount enabled
Tel: [phone]
Toll Free : [phone]
Technical Support: [phone]
Email: [e-mail]
www. is5com.com
Features

All specifications are subject to change without notice. QIG-iPJ2G-2-EN.docx Page—2
www.iS5com.com
Introduction
The iPJ2G PoE Injector is an advanced IEEE802.3 af /802.3atcompliant device with intelligent detection
that provides 10/100/1000Base-T(X) PoE output. The device does not turn on power until it detects a
valid PoE signature from the PoE devices attached downstream on the Ethernet cable. This protection
against damage to non-PoE compliant equipment which may be connected to the Ethernet cable.
Because of this intelligent detection, only an IEEE 802.3at/802.3af compliant device can be powered
with the iPJ2G PoE Injector. iPJ2G can accept 12~57VDC power input and convert to 50VDC to meet the
power input requirement of PoE standard. The iPJ2G PoE Injector can function with any PoE P.D.
equipment which is fully compliant with the IEEE802.3 af /802.3atstandards.
Note: The equipment being powered must be fully compliant with IEEE802.3 af /802.3atfor its power
supply to be able to sense the PoE devices signature and apply power. The power is to be connected on
Ethernet pins 1/2(V+) and 3/6(V-).
Power Connection Guide
Power Supply
12 –57VDC
Frame
Ground

All specifications are subject to change without notice. QIG-iPJ2G-2-EN.docx Page—3
www.iS5com.com
Specifications
iS5Com PoE Injector Model
iPJ2G
Physical Ports
10/100/1000 Base-T(X) Port in RJ45 Auto MDI/MDIX
1
10/100/1000Base-T(X) P.S.E. Port in RJ45 Auto MDI/MDIX
1
Operating Voltage
Input Voltage
12 ~ 57 VDC on 4-pin terminal block
Output Voltage
50V / 600mA, 60 Watts max
LED indicators
Power Indicators
PWR / Ready: 1 x LED
Green On: Power is on and functioning normally.
PoE Indicator
LED
Blue On: PoE Device Link
Blue Blinking: Detecting PoE Device
Blue Off: None PoE Device Detected
Protection
Short Circuit Protection
Present
Over Load Protection
Present
High Voltage Protection
Present
Physical Characteristics
Enclosure
IP-40 Galvanized Steel
Dimensions
1.74 (W) x 2.9 (D) x 4.21 (H) inches
Weight (est.)
~ 400 g
Environmental
Storage Temperature
-40 to +85˚C (-40 to 185˚F)
Operating Temperature
-40 to +85˚C (-40 to 185˚F) No Fans
Operating Humidity
5% to 95% Non-condensing
Regulatory Approvals
EMI
FCC Part 15, CISPR (EN55022) class A,
EMS
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT),
EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8,
EN61000-4-11
Shock
IEC60068-2-27
Free Fall
IEC60068-2-32
Vibration
IEC60068-2-6
Safety
EN60950-1
Warranty
Warranty
5Years

All specifications are subject to change without notice. QIG-iPJ2G-2-EN.docx Page—4
www.iS5com.com
Installation
Dinrail Installation Setup

All specifications are subject to change without notice. QIG-iPJ2G-2-EN.docx Page—5
www.iS5com.com
Wall mount Installation Setup

All specifications are subject to change without notice. QIG-iPJ2G-2-EN.docx Page—6
www.iS5com.com
Front Panel
Connector and Pin Definition
1000Base-T
RJ-45 Input (Data Only)
RJ-45 Output (Data and Power)
Symbol
Description
Symbol
Description
1
BI_DA+
Data BI_DA+
BI_DA+ (Vdc+)
Data BI_DA+ and Feeding power (+)
2
BI_DA-
Data BI_DA-
BI_DA- (Vdc+)
Data BI_DA- and Feeding power (+)
3
BI_DB+
Data BI_DB+
BI_DB+ (Vdc-)
Data BI_DB+ and Feeding power (-)
4
BI_DC+
Data BI_DC+
BI_DC+
Data BI_DC+
5
BI_DC-
Data BI_DC-
BI_DC-
Data BI_DC-
6
BI_DB
Data BI_DB-
BI_DB- (Vdc-)
Data BI_DB- and Feeding power (-)
7
BI_DD+
Data BI_DD+
BI_DD+
Data BI_DD+
8
BI_DD-
Data BI_DD-
BI_DD-
Data BI_DD-
10/100Base-T(X)
RJ-45 Input (Data Only)
RJ-45 Output (Data and Power)
Symbol
Description
Symbol
Description
1
Rx+
Data Receive
Rx+ (Vdc+)
Data Receive and Feeding power (+)
2
Rx-
Data Receive
Rx- (Vdc+)
Data Receive and Feeding power (+)
3
Tx+
Data Transmit
Tx+ (Vdc-)
Data Transmit and Feeding power (-)
4
NC
Not Connected
NC
Not Connected
5
NC
Not Connected
NC
Not Connected
6
Tx-
Data Transmit
Tx- (Vdc-)
Data Transmit and Feeding power (-)
7
NC
Not Connected
NC
Not Connected
8
NC
Not Connected
NC
Not Connected
Note: pins 3 and 6 (-Vdc) should not be shorted to ground
Gigabit PoE Port
PoE LED
Power LED
Gigabit Data Port

All specifications are subject to change without notice. QIG-iPJ2G-2-EN.docx Page—7
www.iS5com.com
Accessories (some are ordered separately)
① 4-Pin Terminal block
② Dust Cover (RJ-45)
③Wall-mounted bracket
④DIN-Rail bracket
⑤ Quick Installation Guide QIG
Packing list
Model Name
Model Description
Description
iPJ2G
Industrial 2-port Gigabit High Power PoE Injector,
24V~57V Input Support
①x 1, ②x 2, ③x 1 or ④x 1, ⑤x 1

All specifications are subject to change without notice. QIG-iPJ2G-2-EN.docx Page—8
www.iS5com.com
Communication Connections
1000Base-T Ethernet Port Connection
 RJ45 (8-pin, MDI) Port Pinouts
 RJ45 (8-pin, MDI-X) Port Pinouts
Pin #
MDI
Pin #
MDI
1
BI_DA +
1
BI_DB +
2
BI_DA -
2
BI_DB -
3
BI_DB +
3
BI_DA +
4
BI_DC +
4
BI_DD +
5
BI_DC -
5
BI_DC -
6
BI_DB +
6
BI_DA +
7
BI_DD +
7
BI_DC +
8
BI_DD -
8
BI_DC -
10/100Base-T(X) Ethernet Port Connection
 RJ45 (8-pin, MDI) Port Pinouts
 RJ45 (8-pin, MDI-X) Port Pinouts
Pin #
MDI
Pin #
MDI
1
Tx +
1
Rx +
2
Tx -
2
Rx -
3
Rx +
3
Tx +
6
Rx -
6
Tx -
 RJ45 (8-pin) to RJ45 (8-Pin) Straight-Through Cable Wiring
Switch Port
NIC Port
RJ-45 Connector
RJ-45 Connector
Tx +
3 3
Rx +
Tx -
6 6
Rx -
Rx +
1 1
Tx +
Rx -
2 2
Tx -
 RJ45 (8-pin) to RJ45 (8-Pin) Cross-Over Cable Wiring
Switch Port
(NIC Port)
Switch Port
(NIC Port)
RJ-45 Connector
RJ-45 Connector
(Rx +) Tx +
3 1
(Rx +) Tx +
(Rx -) Tx -
6 2
(Rx -) Tx -
(Tx +) Rx +
1 3
(Tx +) Rx +
(Tx -) Rx -
2 6
(Tx -) Rx -