Island Oasis SB3X User manual

S
B
3
X
The Taste of Paradise™
SERVICE MANUAL

1
SERVICE MANUAL PAGE
SECTION I GENERAL INFORMATION............................................ 2
II GENERAL REPAIRS..................................................... 13
III PARTS......................................................................... 32
IV TROUBLESHOOTING ................................................. 41
VDAILY CLEANING PROCEDURES ............................... 43
VI POLICIES..................................................................... 44

2
SECTION I
GENERAL INFORMATION
PART 1. SPECS
2. RECEIVING YOUR SHAVER/BLENDER
3. SET UP AND INSTALLATION
•ICE HOPPER/SAFETY SWITCH
•DRAIN HOSE CONNECTION
•LEG ADJUSTMENT
•DRINK DISPLAY BOARD
• ADJUSTMENTS
•TIMING
•ICE FLOW
4. OPERATION—MAKING A FROZEN DRINK
•MULTIPLE DRINKS
5. MAINTENANCE

3
PART 1.
SPECIFICATIONS
The Shaver/Blender was designed to offer our customer:
1. Speed: Just 9 seconds for a 12 oz. drink
2. Consistency: Produces a perfect drink every time
3. Portion Control: No product waste
4. Versatility: Ability to produce many different drinks without
making special adjustments
DIMENSIONS
Height - 27”
Depth - 16”
Width - 14”
ELECTRICAL
6.7 Amps/115 Volts
(Standard Outlet)
WEIGHT
53 Pounds

4
PART 2.
RECEIVING YOUR SHAVER/BLENDER
Upon receipt of your Shaver/Blender please check that all parts are
included and that no damage has occurred during shipment. Save all
shipping cartons and notify Island Oasis with any problems.
CONTENTS
CARTON #1
•Machine
Total Weight: 59 Pounds
CARTON #2
•Ice Hopper
• Hopper Cover and 3 Screws
•2Blender Cups
•210 oz. Measuring Cups
•Safety Switch Rod
•Drain Hose (5 ft.)
•Cleaner
•Cleaning Instructions
•Operation Manual
•Frozen Drink Guide
Total Weight: 11 Pounds

5
PART 3.
SET UP AND INSTALLATION
1. Prior to installations, check the general operation of the Shaver/
Blender at your office (See #7 Adjustments).
2. When removing the machine from its carton, lift from its base. Do
not lift from the Ice Skirt.
3. ICE HOPPER/SAFETY SWITCH INSTALLATION
As of July, 1990 all Shaver/Blender's will have Safety Switches. This
is a requirement of Underwriters Laboratory. The function of this
switch is to cut power to the machine when the Hopper Cover is
removed.
STEP 1. Remove four Screws securing the Ice Hopper Skirt.

6
PART 3.
SET UP AND INSTALLATION (Cont.)
STEP 2. With Ice Hopper upside down, slide Safety Switch Rod
into Sleeve. Attach Ice Skirt to Ice Hopper.
4. DRAIN HOSE CONNECTION
A. Attach hose to the Drain Port located beneath the base of
the machine.
B. Position Drain Hose downward for maximum water flow
Important! Keep an air space between Hose and Drain
Receptacle. Do not plumb directly to Drain Pipe.

7
PART 3.
SET UP AND INSTALLATION (Cont.)
5. LEG ADJUSTMENT
In order for water to drain properly, position the machine on a
level surface and adjust legs so that the machine will tilt at a slight
angle to the rear.
6. DRINK DISPLAY BOARD
Familiarize yourself with the Drink
Board functions prior to operating.
On/Off Switch: Provides power to the
unit.
Stop Button: When activated,
machine will shut down
and cancel drink cycle.
Drink Buttons: Drink cycle will begin
when any of these
buttons are pushed.
Shaver/Blender Buttons: Use these to manually shave ice and to
manually blend.

8
PART 3. SET UP AND INSTALLATION (Cont.)
7. ADJUSTMENTS
A. Shaver and Blender Motor Timing
Timing on both Shaver and Blender Motors is set at the factory.
Be sure to check these adjustments prior to installation. The
drink cycle will run for a total of nine seconds. The Shaver
Motor will engage at the press of the Drink Button and run for
four seconds. The Blender Motor will engage two seconds after
Drink Button is pushed and run for seven seconds. These
adjustments will vary according to the drink size. (Please refer
to STEP 3 of Ice Flow Adjustment.)
Timing adjustments are very sensitive.
Therefore, only slight turns of the
Adjustment Screws are necessary.
Turn right to increase timing and left
to decrease. (Timing adjustments
should only be used to make the
texture of shaved ice finer, i.e.
smoothies. Not to be used for ice
flow adjustments.)
B. Ice Flow Adjustment
Adjustment of the Ice Flow is key to the function of the Shaver/
Blender, and weighing the ice is the only accurate
measurement. Because ice texture varies, this adjustment must
be made at the time of installation.

9
PART 3.
SET UP AND INSTALLATION (Cont.)
B. Ice Flow Adjustment (Cont.)
STEP 1.
Fill Ice Hopper to within one inch
of the top.
STEP 2.
Adjust ice flow for the desired size
drink. Adjustment screw is located
to the right of the ice chute. (Turn
the adjustment nut clockwise for
more ice and counter clockwise
for less ice.)
Use the following chart for
calibrating to the desired size drink.
DRINK SIZE MIX LIQUOR ICE
10 oz. 3.5 oz. 1-11/oz. 6 oz.
12 oz. 4.0 oz. 1-11/oz. 7.0 oz.
14 oz. 4.5 oz. 1-11/oz. 8.0 oz.
16 oz. 5.5 oz. 1-11/oz. 9.0 oz.
The plastic ice container and
Pelouze Scale shown are available
through Island Oasis.
2
2
2
2

10
PART 4.
OPERATION—MAKING A FROZEN DRINK
The following is based on a 12 oz. drink.
STEP 1.
Thaw product completely, shake
well and pour 4 oz. into
measuring cup.
STEP 2.
Pour 1-1/2 oz. of liquor into
measuring cup.
NOTE: When making non-alcoholic
drinks, substitute liquor by
increasing Island Oasis mix by one
ounce.

11
PART 4.
MAKING A FROZEN DRINK (Cont.)
STEP 3.
Pour contents of measuring cup
into Blender Cup.
STEP 4.
Place Blender
Cup on base
and press the
#1 Drink
Button.
STEP 5.
Remove Blender Cup and pour into glass. The finished
product should have a smooth, consistent texture that will
fill the glass to the top.

12
PART 4.
MAKING A FROZEN DRINK (Cont.)
MULTIPLE DRINKS
Once the SB3-X has been calibrated for a particular drink size, it
is important to pour the correct amount of product and liquor
for multiple drinks. The following chart is based on multiple
drink formulations for a 12 oz. drink.
NO. OF DRINKS PRODUCT LIQUOR ICE*
14oz. 1 to 1-1/2 oz. 7 oz.
28oz. 2 to 2-1/2 oz. 14 oz.
3 12 oz. 3 to 3-1/2 oz. 21 oz.
*NOTE: Once the ice flow has been set, no adjustment is needed for
multiple drinks.

13
SECTION II
GENERAL REPAIRS
PART 1. MAIN POWER BOARD
2. DRINK DISPLAY BOARD
3. SHAVER MOTOR
4. BLENDER MOTOR
5. BLENDER BASE BEARINGS
6. MAIN SHAFT BEARINGS
7. ICE SHAVER BLADE
8. RESET SWITCH
9. DRAIN SYSTEM
10. BLENDER CUP
11. SAFETY SWITCH

14
IMPORTANT
When performing interior repairs, begin by following these basic
steps.
1. Turn off Power Switch
2. Disconnect Power Cord
3. Remove Ice Chute
4. Remove Front and Rear Covers*
*Swing Front Cover to the right when removing. This will
avoid damage to Drink Board connections.

15
PART 1.
MAIN POWER BOARD
DESCRIPTION
The main Power Board functions as the control center of the
Shaver/Blender.
TROUBLESHOOTING
A. On occasion, water damage may occur due to condensation
build-up on the Power Board. This will cause the unit to
malfunction.
Main Power Board

16
PART 1.
MAIN POWER BOARD TROUBLESHOOTING (Cont.)
B. If the Main Power Board fuse is blown, there will be a loss of
power to the Shaver/Blender. Replace fuse located at the top
right of Power Board. You may find it necessary to remove
Power Board from its housing. (Fuse rating 0.1 amp).
REPLACEMENT
1. Follow beginning steps.
2. Remove Cover from housing.

17
PART 1.
MAIN POWER BOARD REPLACEMENT (Cont.)
3. Pinch four white spacers in order to
remove Power Board from its
housing.
4. Disconnect wiring to Main Power
Board (see Wiring Diagram).
5. Install new Board by following
reverse procedures.
PART 2.
DRINK DISPLAY BOARD
DESCRIPTION
Serves as the Main Control Center for all functions of the machine.
TROUBLESHOOTING
If Drink Board functions do not work properly, check connections
to Main Power Board and for any condensation build-up on wire
connections. Before replacing Drink Board, plug in a new board
and test functions.
REPLACEMENT
1. Follow basic first steps.
2. Disconnect wire connections to Main
Power Board.
3. Remove top and bottom screws
securing Drink Board.

18
PART 2.
DRINK DISPLAY BOARD REPLACEMENT (Cont.)
4. Remove center nut and bolt. You will have to access center
bolt through front of Board. Remove On/Off Switch and
decal to locate bolt. Be sure to save Drink Board insulator.
5. Make certain Drink Board is placed into position properly.
Note that the connector wires sit to the right of the Board.
6. Do not over tighten center nut, or fastening screws too
tight. Board will not operate correctly.