IsoLux IsoLED PLUS User manual

1
IsoLux llc, 1045 Collier Center Way, Naples, Florida USA 34110 phone: [phone]
fax: [phone] email: [e-mail] web: www.isoluxllc.com
OPERATION MANUAL
IsoLED PLUS
PORTABLE LED HEADLIGHT

2
IsoLux llc, 1045 Collier Center Way, Naples, Florida USA 34110 phone: [phone]
fax: [phone] email: [e-mail] web: www.isoluxllc.com
The IsoLED Plus system consists of:
•2 Re-chargeable control units (Battery
Pack) with belt clip
•LED Illuminator with variable spot
control
•Choice of dual adjust ratchet or soft
headband
•2-meter Cable Assembly
•Wall mounted Battery Charger
IsoLED Control Unit (Battery Pack)
•Weighs only 190 grams
•On/Off Intensity Control Knob (3-100%
adjustability)
•On indicator
•Re-Charge Plug-in Connector
•Belt clip
•Additional units can be purchased separately
IsoLED Illuminator
•Variable spot, 10-100mm diameter at 400mm/16” or 20-230mm diameter at 1m/39”
•Flexible linkage for infinite positional control
•Removable/sterilizable positioning joystick
•Attached to dual adjustable ratchet headband or soft Velcro headband
Battery Charger
•Universal AC input, 100 to 240 VAC
•Indicator light, goes from red to green when fully charged
•Wall mounted unit
1.0 SPECIFICATIONS
Illumination
> 31,000 lux @ 30 cm
LED Life
> 50,000 hours
Color Temperature
4,500 °K
Color Rendition Index (CRI)
96 Typical, with R9 > 90
Light Degradation
None
Spot Size
10mm to 100mm at 400mm/16” working distance
Intensity Range
20% to 100%
Operating Time
>3.5 hours typical at maximum intensity; 7 hours with 2 Power Packs
Normal Recharge Time
3.6 hours
Quick Recharge Time
2 hours, for 3 hours of maximum intensity
Headband
Dual ratchet or soft Velcro
Weight (headlight)
290 grams (LED, headband, cable and optics)
Weight (battery)
190 grams
Size (control unit/battery pack)
4.25” x 2.7” x 1.1”

3
IsoLux llc, 1045 Collier Center Way, Naples, Florida USA 34110 phone: [phone]
fax: [phone] email: [e-mail] web: www.isoluxllc.com
2.0 OPERATING INSTRUCTIONS
2.1 Charging the Battery
1. Plug the charger’s male connector into the receptacle on the Battery Pack.
2. Plug the AC connection into a 100-240 VAC source.
3. The charger indicator light will illuminate red while charging and turn green when charging is
complete (approximately 3.6 hours).
4. An 85% partial charge may be performed in 2 hours.
5. Disconnect the charger from the AC source and unplug the charger from the control unit.
2.2 Illuminator and Headband Operation
1. Plug the Cable Assembly into the illuminator unit receptacle. There are red orientation dots that
must be aligned.
2. The cable should be routed and snapped into place through a set of two cable clips. For dual ratchet
headsets one is located on the top on the crown and one on the rear of the headband. The user has
the choice of using the set on the left or the right.
3. For softband/velcro headsets, the cable should be routed through two clips along the circumference.
4. The illumination spot size may be adjusted by turning the grooved dial on the headlight.
5. The linkage assembly on the headband allows for personal positioning control. The joystick is used
to further adjust the position of the light beam.
2.3 Control Unit / Battery Pack Operation
1. Assure the Cable Assembly is plugged into the illuminator unit receptacle. There are red orientation
dots that must be aligned.
2. Plug the other end of the Cable Assembly into the Control Unit/ Battery Pack receptacle, once again
aligning the red dots.
3. Clip the control unit where desired or place in a pocket.
4. Turn the ON/OFF and intensity control knob clockwise to turn unit On (switch will close). This knob
also controls the intensity.
5. To turn unit Off, turn control knob counter-clockwise until switch opens.
6. When battery has discharged to a level too low to maintain operation, the Illuminator will dim or
flicker and the green LED on the control panel will turn off.
7. The unit’s operational time could be extended from 3½ hours at full intensity to greater than 7 hours
by using the illuminator at half intensity.
Figure 1 - Control Unit / Battery Pack
ON Indicator
ON/OFF &
Intensity
Control
Charge Plug-in
Connector
Control Unit
Cable Receptacle

4
IsoLux llc, 1045 Collier Center Way, Naples, Florida USA 34110 phone: [phone]
fax: [phone] email: [e-mail] web: www.isoluxllc.com
Figure 2 - Headlight Assembly with Illuminator
3.0 CARE & MAINTENANCE
3.1 Headlight, Headgear and Cable
DO NOT AUTOCLAVE!
Exterior surfaces of headlight, headgear and cable can be wiped clean with any of these solutions:
•Banicide
•Cidex, Cidex Plus, Cidex 7
•Metracide
•10% Wescodyne
•10% bleach
•70% isopropyl alcohol
•Wavecide-01
•Mild soap
Headbands and headlight modules can not be immersed into disinfecting liquids or sterilizers.
Keep ends of cable clean by wiping with a damp cloth. Allow to dry before use.
Clean the optics only with lens tissue available at any camera store. Follow the instructions on the
package.
To insure long life for the headgear, cable and power source, store them in a cool dry environment.
3.2 Joystick
Joystick can be sterilized after unscrewing from headlight.
DO NOT AUTOCLAVE ANY OTHER PARTS OF THE HEADLIGHT SYSTEM !

5
IsoLux llc, 1045 Collier Center Way, Naples, Florida USA 34110 phone: [phone]
fax: [phone] email: [e-mail] web: www.isoluxllc.com
4.0 WARNINGS AND CAUTIONS
4.1 Warnings
Users of this headlight should be trained in the appropriate surgical procedures.
They should read and understand the owner’s manuals for this Headlight and all equipment used
in conjunction with it.
4.2 Cautions
Do not look directly into headlight when illuminated. Eye injury may result.
Do not use at distances closer than 10in(25cm) for extended periods. Erythema
may result.
Service must be performed only by IsoLux authorized repair personnel.
5.0 Color Rendition Index (CRI)
The color rendering index (CRI), with a scale from 0 to 100 %, is a quantitative measure of
the ability of a light source to reveal the colors of various objects faithfully in comparison
with an ideal or natural light source like the light from the sun. Light sources with a high
CRI are desirable in color-critical applications such as neonatal care, medicine and
surgery, as it shows the true colors of tissues and skin, thereby reducing the time to
diagnosis and surgery.
The IsoLED Plus unit has a high CRI of 96, which brings it close to the optimum value of
100, and is one of the few units in the global market with this specification.

6
IsoLux llc, 1045 Collier Center Way, Naples, Florida USA 34110 phone: [phone]
fax: [phone] email: [e-mail] web: www.isoluxllc.com
6.0 WARRANTY AND SERVICE
6.1 Headlight
The IsoLux IsoLED Plus Headlight System is guaranteed against all defects in materials and
workmanship. All surgical Headlight Optical Modules and Connecting XYZ Mechanisms are
warranted for the lifetime of the purchaser.
This warranty coversthe replacement of the parts only and does not include any on-site labor costs.
This warranty is void if service is performed by persons other than authorized IsoLux llc distributors
or representatives or if equipment is interconnected with components not manufactured by IsoLux
llc and/or have not been approved by IsoLux llc for compatibility.
6.2 LEDs
IsoLux llc warrants the LED’s a full five (5) years, by normal use only. IsoLux reserves the right to
void this warranty if any non authorized power source is used in conjunction with the head set or if
liquids are allowed to ingress the optical head or control unit.
7.0 ORDERING PARTS AND COMPONENTS
The IsoLux llc IsoLED Plus Headlight is designed for use with the IsoLux llc power source
only.
Accessories Order #
DC Rechargeable Control Unit/Power Pack IL-2295
Headlight Illuminator IL-2298
Cable Assembly FO-2068
Battery Charger IL-2187
Replacement Sweatbands (pack of four sets): IL-2297
Replacement Joysticks (pack of 2): FO-0911
Replacement Head Gear FO-2072